I notice that there is new version released today 6.4.10 rel so l updated by box an will monitor
Thanks for all you help fingers crossed it’s been resolved
I notice that there is new version released today 6.4.10 rel so l updated by box an will monitor
Thanks for all you help fingers crossed it’s been resolved
Thank you for your input
I will have another look for the setting as l have previous loook for a setting
I have an octagon Sf8008 with openvix running however about every 2 hours l need to reboot GUI. Is there a setting to prevent having to reboot and keep live
Hi
I can confirm that CCcam 2.3.1 is working on on Technomate twin 4k
thanks for your help
I have tried loading the vix version "enigma2-plugin-softcams-cccam-2.3.1_vix_armv7ahf-neon.ipk" on the Technomate twin 4k. It was unsuccessful
On the installation it indicated that there was a collection error with the load file. I initially tried with 5.1.016 but upgraded and now using Openvix 5.1.019
but same error
thanks Mckee25 but i copied CCcam to the usr/softcams and config to /ect when loading which enable me to test but would not activate and as indicated the config is working on another box
The CCcam.cfg file in /etc is good use with Mipsel but not with openvix "enigma2-plugin-softcams-cccam-2.3.1_atv_armv7ahf-neon.ipk" on Technomate twin4k
Tried installing the atv version on technomate twin4k openvix and it load but does not run
Can anyone advise where can i find a cccam 2.3.1 for technomate 4k openvix
Thanks
Thanks for your response but l am not sure where that is. Have looked at latest oscam 11398? arm patched download but dont see the download for the technomate twin 4k?
Hi
Thanks for viewing. That was my first place to view but they are older version and l think the latest is 11398 but can't find the location to download
Hi
Can you help l am looking for the latest OSCAM ipk for twin 4k
Thanks
Hi
i am looking for enigma2-plugin-softcams-oscam.emu-11399-r766_openvix_armv7ahf-vfp-neon.ipk for technomate twin 4k
can you advise where to download
Thanks
Hi
Do you have the latest Oscam for Technomate twin 4k PowerVu stream relay
Hi
Thanks for the new version enigma2-plugin-softcams-oscam.emu-11399-r766_openatv_armv7ahf-vfp-neon.ipk
I can confirm it working on the Technomate twin 4k
One quick question does this have Power VU , stream relay ?
Tried installing the Openatv oscam - emu 11392 armv7 on Technomate twin 4k without success
It loads ok and configuration it as installed on a TM-Namo m3 (oscam - emu 11392)
Have looked for an earlier version or a later version with out success
any help welcome
Hi
Thanks for the downloads however when installing them and loading dreamplex it identified others:
grateria-core, libpython 2.7-1.0, python-core, Python-1.0, python-re, python-stringolda dn LIBc6
Not sure if there are other dependencies? but appreciate your help
Hi
I am new to Enigma 2 and have a IPbox 9000hd installed running E2 Hyperion 5.3.1
I have installed Dreamplex with “enigma2-plugin-extensions-dreamplex_2.1.3_all.ipk” and when installing and using the system check it advised that “can’t satisfy as the python-pyopenssl, python-textutils and curl”
Looked back at previous version and these were added to release “enigma2-plugin-extensions-dreamplex_2.0.1_all.ipk” but l am unable to load this release as you don’t seem able to downgrade?
Have they been left out of this plugin release? How can l get these dependencies?
Any help appreciated