Take a software update after installation.
Currently stable now, so long, after software update.
Take a software update after installation.
Currently stable now, so long, after software update.
unstable
Including Softcam downloads
openpli-6.0-dm500hd-20170702.nficc098d6049eaddbc1c86c.jpg
Then it is important that .server file refers to the location of softcam.key
Blue button / device manager
There is probably what is added to config.files that essentially determines what a softcam can read, and not the softcam version.
Now I'm unsure.
My Oscam.server file is intended for tuners with 1 card reader
"2017/08/23 16:32:25 58F782A1 r reading key file: /etc/tuxbox/config/oscam/SoftCam.Key". It seems to stop here.
Is this the correct location of softcam.key ev oscam.server ?
I use: /etc/tuxbox/config/SoftCam.Key" and
/etc/tuxbox/config/oscam.server".
Try editing this in your oscam.server file.
If you use softcam.key
[reader]
label=emulator
protocol=emu_2
device=/etc/tuxbox/config/SoftCam.Key
fallback=1
detect=cd
group=2
emmcache=1,1,2,1
opendroid-6.3-dm500hd-20170711
Hi...
Ftp over cccam.cfg file to / var / etc /
There is a cccam.cfg there from before which you should confirm overwriting.
Oscam and Ncam are going to / var / etc / tuxbox / config /
Which tuner you have and what image do you use?
Update.
Installed 1.5 spark form first entry, renamed it ncam and set 755. My configs are in var keys and I renamed them all to ncam.xxx etc.
Still cant web browse using ip:8181. My box is alien mini chip 7111 and running Vix 4.
Mystery.
I have not tried Vix imaget with alternative softcam manager, I have tried out on OpevATV, OpenESI and OpenPLI
Try OpenESI 5.0 for Spark. I think it's best to Spark off the images I've tried
You must install ncam from my first entry, Ncam1.7.sh4.
These two downloads belong together
You do not have to rename it, just 755.
Hi Wika,
I am booting my spark / enigma alien in enigma mode. Are the above only to be used when booting to spark. Do I need a different Ncam for running in enigma2.
Thanks in advance.
In enigma2
Hi..
You must use the ncam version in the first entry. Other ncam versions do not work.
Follow the explanation.
Softcam Manager will be installed and available in plugins.
I use it daily on my shd8900
This is no secret so I'll post it here.
Copy and paste this into the oscam.server file.
I have not tested, but this should also work with Ncam
With me it works with all the oscam versions I've tried on the conax Nordic.
[reader]
label=Canal_Digital_Nordic
enable=1
protocol=internal
device=/dev/sci0
detect=cd
group=1
emmcache=1,3,15
audisabled=0
mhz=357
cardmhz=2700
ratelimitecm=4
ratelimittime=9000
ecmunique=1
srvidholdtime=2000
cooldown=30,600
plse power vu ecm emu
I have no knowledge of Power VU
It is possible I misunderstand the question, but it is config.fil which determines which card to read?
I have conax nordic channels, all read by oscam
Ncam1.7 sh4-spark file. For alternative softcam manager.
First install alternativesoftcammanager_20140213-r2_sh4.ipk
FTP over NCAM17.sh4 to / usr / bin / cam. Restart GUI.
FTP Ncam config files and softcam to / usr / keys.
my dear, how to use wlan on this image, or how to activate it?
Thanks for this nice image
I run only on wired networks and can therefore nothing about WLAN.
Non riesco ad aggiungere la lingua italiana....Chi mi da na dritta?
Press the blue button to get to the TS panel.
Select OK softcam.
Then press the blue button again "Install / remove" to load the desired softcams.
There you will find all the softcams for download.