thanks master g for the reply wish to know if you know any oscam that can read conax card
Which oscam can read conax card
-
- General OSCam
- johnkiema
- Thread is marked as Resolved.
-
-
Depends which card / provider it is. Give us a clue..
-
provider startimes
-
This card isn`t on the oscam cards list wiki -> http://www.streamboard.tv/oscam/wiki/CardsList
If it is possible, the configuration isn`t public.
-
hi master g thanks for the reply i wish to know do you have oscam config for card reader on vu solo
-
No, sorry i don`t.
-
It is possible I misunderstand the question, but it is config.fil which determines which card to read?
I have conax nordic channels, all read by oscam -
wika i need the configs and oscam can you send to me
-
plse power vu ecm emu
send me powervu emulator
-
This is no secret so I'll post it here.
Copy and paste this into the oscam.server file.
I have not tested, but this should also work with Ncam
With me it works with all the oscam versions I've tried on the conax Nordic.
[reader]
label=Canal_Digital_Nordicenable=1
protocol=internal
device=/dev/sci0
detect=cd
group=1
emmcache=1,3,15
audisabled=0
mhz=357
cardmhz=2700
ratelimitecm=4
ratelimittime=9000
ecmunique=1
srvidholdtime=2000
cooldown=30,600
plse power vu ecm emu
I have no knowledge of Power VU
-
thanks brother will try it and update you results and thanks alot for response and setting
-
hi wika i tried the settings you gave me it read like this
2017/08/23 16:32:24 6F2A9884 r (reader) upper_card [internal] card detected
2017/08/23 16:32:24 02A49800 r (reader) lower_card [internal] card detected
2017/08/23 16:32:25 58F782A1 r (reader) emulator [emu] found card system emu
2017/08/23 16:32:25 58F782A1 r (reader) emulator [emu] THIS WAS A SUCCESSFUL START ATTEMPT No 1 out of max alloted of 1
2017/08/23 16:32:25 58F782A1 r reading key file: /etc/tuxbox/config/oscam/SoftCam.Key
2017/08/23 16:32:30 6F2A9884 r (reader) upper_card [internal] ERROR: no characters found in ATR!
2017/08/23 16:32:30 6F2A9884 r (reader) upper_card [internal] Deactivating card
2017/08/23 16:32:30 6F2A9884 r (reader) upper_card [internal] Read ATR fail, attempt 1/7 fs = 9
2017/08/23 16:32:35 02A49800 r (reader) lower_card [internal] ERROR: no characters found in ATR!
2017/08/23 16:32:35 02A49800 r (reader) lower_card [internal] Deactivating card
2017/08/23 16:32:35 02A49800 r (reader) lower_card [internal] Read ATR fail, attempt 1/7 fs = 9
2017/08/23 16:32:40 6F2A9884 r (reader) upper_card [internal] ERROR: no characters found in ATR!
2017/08/23 16:32:40 6F2A9884 r (reader) upper_card [internal] Deactivating card
2017/08/23 16:32:40 6F2A9884 r (reader) upper_card [internal] Read ATR fail, attempt 2/7 fs = 8
2017/08/23 16:32:45 02A49800 r (reader) lower_card [internal] ERROR: no characters found in ATR!
-
Which tuner you have and what image do you use?
-
the box is pro v3 solo enginma 2 the image is openpli4 this is the info about tuner
main:
1. DVB-S2/S Tuner
2. BCM7358 752MHZ MIPS Processor
3. 512MB RAM (2*256MB DDR3)
4. Image Support: Openpli,Openvix,OpenATV,OpenHD,Blackhole,Italy7 and so on -
Now I'm unsure.
My Oscam.server file is intended for tuners with 1 card reader
"2017/08/23 16:32:25 58F782A1 r reading key file: /etc/tuxbox/config/oscam/SoftCam.Key". It seems to stop here.
Is this the correct location of softcam.key ev oscam.server ?
I use: /etc/tuxbox/config/SoftCam.Key" and
/etc/tuxbox/config/oscam.server".
Try editing this in your oscam.server file.
If you use softcam.key
[reader]
label=emulatorprotocol=emu_2
device=/etc/tuxbox/config/SoftCam.Key
fallback=1
detect=cd
group=2
emmcache=1,1,2,1
-
thanks for the respond brother i will try it now and I wish to ask if you have a good oscam that can read oscam card will appreciate conax
-
There is probably what is added to config.files that essentially determines what a softcam can read, and not the softcam version.
-
oh okay because I am using oscam emu and softcam with emu keys
-
Then it is important that .server file refers to the location of softcam.key
OSCam Support Forum
Configs, discussion, downloads and guides for OSCam Softcam.
Participate now!
Don’t have an account yet? Register yourself now and be a part of our community!