Posts by 4Him

Quote from s3n0

Hello.

Where are the other configuration files ? A single "oscam.server" file is not enough.

Is AU (Auto-Update : https://wiki.streamboard.tv/wiki/OSCam/en/AU) enabled in Oscam ? And is it configured correctly ?

I don't know CONAX coding systems very well, but if I'm not mistaken, one EMM command is enough to write Entitlemens for CONAX cards, once in a long time (1 hour; 1 day; 1 week; etc.). Then the Entitlements are valid for a long time. So you probably don't have AU enabled in your Oscam ? I dont know. Is it possible that the AU function in your Oscam is not active ? In the file "oscam.conf" and "oscam.user" you need to use the user dvbapi , when it comes to writing EMMs packets via Oscam, to the same Oscam (that is, Oscam serves as both a client and a server at the same time ... and also needs to send EMMs to its card reader).

Display More

hello and thank you for your reply.

I put oscam.server only because I'm not very practiced with oscam so I don't know really what files have an "impact" on the system

I will check if I have AU enabled and I will add .conf and .user files

could you explain why these other files are important please?

thank you again

best regards

Hello

I have AX HD 61 with openatv 6.3 and OSCam r11678-798

I have 3 smartreaders connected via usb hub with three cards

One of these is MTVA Hungary conax card

Sometimes it doesn't work and I need to put it in an official Conax receiver and seems the card "refresh" the right.

This happened also for ANTIKSAT card (that is not listed in oscam file I attach)

can somebody see if I need to set something in my oscam reader file?

thank you best regards

Hello,

I've tried to download tbs drivers but my tbs5980 is not recognized

I have openatv 6,4

I remeber same tuner works on octagon4008 and satdream gr image (but I haven't this receiver anymore)

Can someone help me please? I can't change my image on ax hd 61

thank you very much

best regards

hello,

I've a problem with enigma2 receiver (ax hd61) when I use 2 conax subscritption simultaneously through cam module.


for example digitalb and antiksat.

Digitalb works anyway

antiksat works just when digitalb cam is unplugged.


I've tried to assign antiksat caid in "common interface assignment" but it doesn't work.



is the same with nagravision maxtv croatia subscription:

Arena Sport 1 croatia is scrambled both in conax and nagravision and it doesn't work

arena sport 2 croatia no problem (just nagravision flag)

and with nc+ and other cam is the same

for example i put viaccess cam for tv slovenia and nc+ cam and when I tune a nc+ channel the receiver "use" viaccess cam showing "no right for video, no right for audio"

thank you for your kind help



best regards

hello,

I've a problem with enigma2 receiver (ax hd61) when I use 2 conax subscritption simultaneously through cam module.



for example digitalb and antiksat.

Digitalb works anyway

antiksat works just when digitalb cam is unplugged.



I've tried to assign antiksat caid in "common interface assignment" but it doesn't work.



is the same with nagravision maxtv croatia subscription:

Arena Sport 1 croatia is scrambled both in conax and nagravision and it doesn't work

arena sport 2 croatia no problem (just nagravision flag)



thank you for tour kind help



best regards

hello I use oscam-emu in ax hd61

I'm not very good with it

I set in oscam.server internal card reader for a conax hungarian tv card and it works

then i set the same for ar irdeto "fotelka" card and it works only if I switch off the "hungarian reader" through a pc connected via ftp

I've tried to change "group" in both cards reader with no success.

what do I miss?

thank you

best regards

hello do you know if is it possible to flash dr hd F 15 firmware on blade bm7000s?

thank you

regards

hello can someone help me please?

I don't understand

I have followed the guide, the software says: "waiting for rom"

It seems I have not the right usb to rs-232 cable

what do I have to do?

what do I have to buy to try to let this receiver work again?

thank you

regards

hello

I've installed softcam universal feed.ipk on openatv 6.4 (ax hd 61 receiver)

but i can't find softcam in plugin section anyway

why? thank you

best regards

have you find astra.conf with missing tp of 54,9 ?

Quote from saragusa

Hi ciefp . Can you add in astra.conf RTRS tp at 54,9e: 12648V, 5120, 3/4, 8PSK, T2-MI?

hello do you have it?

hello master g

finally I managed to put and read another card on smartmouse. problem is the same. after 1 minutes it stops descrambling:

• 2020/05/11 21:39:20 1471EEEC r (reader) TVR [conax] Warning: needed try nr 2, next ECM has some delay
• 2020/05/11 21:39:20 14B1D6F4 c (ecm) dvbapi (0B1D@000000/0000/0068/67:5367FDC576610EC4B29D9858C22A3D7F): timeout (5000 ms) by TVR

the thing is that there's the same problem that comes over with 2 different card can that give you a solution about it?

If this can help you: i'm unable to update my usb smargo argolis smartreader. If I plug into my notebook and I launch the update tool It doesn't find it

thank you

please just tell me for now how to let biss working

Quote from master G

Quote from 4Him

More than everything now ABERTIS on 30west don't work anymore

Did you not read that i removed the readers and anything to do with oscam emu to get the cards working first ?

Its maybe best you go back to your original configs and setup because we seem to be going around in circles here.

sorry it's because i'm totally new and unable with these things. so I missed it

what do i have to do to let biss works again?

and do you know why smartmouse don't work?

I promise i will not disturb you anymore:)

thank you

Quote from master G

You had no accounts setup for the cards in oscam.user.

I`ve removed all configs and files related to OSCam EMU to make sure your cards work properly without the extra configurations.

Insert TVR_S into the internal card slot and MTVA_I into the smargo.

Show another log if it doesn`t work.

internal card reader works. smartmouse (MTVA) not: this is the log:

• 2020/05/05 21:54:31 266576B6 r (reader) MTVA_I [mouse] Warning: needed try nr 2, next ECM has some delay
• 2020/05/05 21:54:51 266576B6 r (reader) MTVA_I [mouse] card system not supported
• 2020/05/05 21:54:51 266576B6 r (reader) MTVA_I [mouse] Normal mode failed, reverting to Deprecated Mode
• 2020/05/05 21:54:52 266576B6 r (reader) MTVA_I [mouse] ATR: 3B 34 94 00 30 42 30 30
• 2020/05/05 21:54:53 266576B6 r (reader) MTVA_I [mouse] type: Conax, caid: 0B1D, serial: ##########, hex serial: ########, card: v64
• 2020/05/05 21:54:53 266576B6 r (reader) MTVA_I [mouse] Providers: 1
• 2020/05/05 21:54:53 266576B6 r (reader) MTVA_I [mouse] Provider: 1 Provider-Id: 000000
• 2020/05/05 21:54:53 266576B6 r (reader) MTVA_I [mouse] Provider: 1 SharedAddress: ########
• 2020/05/05 21:54:53 266576B6 r (reader) MTVA_I [mouse] found card system conax
• 2020/05/05 21:54:53 266576B6 r (reader) MTVA_I [conax] THIS WAS A SUCCESSFUL START ATTEMPT No 1 out of max allotted of 1
• 2020/05/05 21:54:54 266576B6 r (reader) MTVA_I [conax] Package: 1, id: 1070, classes: 01FFFFFF, date: 1990/01/01 - 1990/01/01, name: Preview 1
• 2020/05/05 21:54:54 266576B6 r (reader) MTVA_I [conax] Package: 2, id: 1070, classes: 01FFFFFF, date: 1990/01/01 - 1990/01/01, name: Preview 1
• 2020/05/05 21:54:54 266576B6 r (reader) MTVA_I [conax] Package: 3, id: 1080, classes: 01FFFFFF, date: 1990/01/01 - 1990/01/01, name: Preview 2
• 2020/05/05 21:54:54 266576B6 r (reader) MTVA_I [conax] Package: 4, id: 1080, classes: 01FFFFFF, date: 1990/01/01 - 1990/01/01, name: Preview 2
• 2020/05/05 21:54:54 266576B6 r (reader) MTVA_I [conax] Package: 5, id: 1010, classes: 010001FB, date: 2020/05/01 - 2020/05/31, name: Zone 01
• 2020/05/05 21:54:54 266576B6 r (reader) MTVA_I [conax] Package: 6, id: 1010, classes: 010001FB, date: 2020/04/01 - 2020/04/30, name: Zone 01
• 2020/05/05 21:54:54 266576B6 r (reader) MTVA_I [conax] Package: 7, id: 1020, classes: 01000001, date: 2020/03/01 - 2020/03/31, name: Zone 02
• 2020/05/05 21:54:54 266576B6 r (reader) MTVA_I [conax] Package: 8, id: 1020, classes: 00000000, date: 1990/01/01 - 1990/01/01, name: Zone 02
• 2020/05/05 21:54:54 266576B6 r (reader) MTVA_I [conax] ready for requests
• 2020/05/05 21:54:54 00000000 s (main) init for all local cards done
• 2020/05/05 21:54:54 74502B76 c (client) plain dvbapi-client granted (linuxsatsupport, au=on (1 reader))
• 2020/05/05 21:54:54 74502B76 c (dvbapi) dvbapi channelcache loaded from /etc/tuxbox/config/oscam-emu/oscam.ccache
• 2020/05/05 21:54:54 74502B76 c (dvbapi) Detected /dev/dvb/adapter0/demux0 Api: 0, userconfig boxtype: 1 maximum number of filters is 64 (oscam limit is 64)
• 2020/05/05 21:54:54 74502B76 c (dvbapi) ERROR: ioctl(CA_GET_DESCR_INFO): Invalid argument
• 2020/05/05 21:55:00 74502B76 c (dvbapi) Demuxer 0 ecmpid 0 CAID: 0B1D ECM_PID: 0130 PROVID: 000000
• 2020/05/05 21:55:00 74502B76 c (dvbapi) Demuxer 0 found 1 ECM pids and 6 STREAM pids in CA PMT
• 2020/05/05 21:55:00 74502B76 c (dvbapi) Demuxer 0 no suitable readers found that can be used for decoding!
• 2020/05/05 21:55:05 74502B76 c (dvbapi) Demuxer 0 no enabled matching ecmpids -> decoding is waiting for matching readers!

and now ABERTIS on 30west as long as other BISS don't work anymore

Quote from master G

Oh dear.. Attach all your configs so i can can see what the problem is.

sorry to bother you and big thanks for your kind help :)test.zip

Quote from master G

Is this working ? If not show a log.

this is for tvr

mtva is fta at the moment and i can not check it

i put your file. i have tvr in the internal reader. mtva on smartmouse

• 020/05/05 19:55:07 134A0F5C c (ecm) dvbapi (0B02@000000/0000/0002/67:F3E8AD3C6B3412BE7B11C7BE48E579CB): rejected group (1 ms) (no matching reader)
• 2020/05/05 19:55:07 134A0F5C c (ecm) dvbapi (0B02@000000/0000/0002/67:F3E8AD3C6B3412BE7B11C7BE48E579CB): rejected group (0 ms) (no matching reader)
• 2020/05/05 19:55:07 134A0F5C c (dvbapi) Demuxer 0 restarting decoding requests after 0 ms with 1 enabled and 0 disabled ecmpids!
• 2020/05/05 19:55:07 134A0F5C c (dvbapi) Demuxer 0 trying to descramble PID 0 CAID 0B02 PROVID 000000 ECMPID 0B02 ANY CHID PMTPID 1B5A VPID 00C8
• 2020/05/05 19:55:08 134A0F5C c (ecm) dvbapi (0B02@000000/0000/0002/67:F3E8AD3C6B3412BE7B11C7BE48E579CB): rejected group (0 ms) (no matching reader)

Quote from master G

Quote from 4Him

if so can you modify my oscam file in order to do that please?

Modified oscam.server attached.

Edit the accounts for these cards in oscam.user

TVR_S is now group = 1

MTVA_I is now group = 2

in oscam server i have this how to modify?

and sorry I don't understand have you put tvromania has internal reader?

hello nothing change setting mhz 500

since i have changed oscam dvapi I have no video neither for few seconds also if I have removed P: 0B02:000000

any other suggestion?

do you suggest to change smartmouse reading from tvr card to mtva card?

then I will switch tvr to internal reader

maybe in this way it will work

if so can you modify my oscam file in order to do that please?

thank you very much best regards

hello it's a smargo argolis smartreader

here in the attachment oscam file

I don't know where to catch other log more than what I've posted above

thank you

oscam.zip