Thank you very much for your support, I will buy it next week and will contact you in case I can't do it myself. Love and peace!
Posts by brutus1979
-
-
Excuse my ignorance but if I download the entire channel list ( m3u ) , let's say...0.8W from webif (enigma2) will it work? As far as I know it's not a simple url...but I hope you'll help me when I get the device. Thanks again!
-
Thank you very much for the information, I will do a test but first I have to buy it. Thanks again.
-
Thanks for the reply, I need to look for some tutorials, I'm not familiar with this.
-
Hello everyone, it's been a while since I've been on the forum (personal issues) so....excuse the question. Can someone explain to me how I could restream enigma2 bouquet outside my home network? Thank you!
-
solved, I installed openatv 7.4 beta clean image, enigma2_plugin_extensions_multi_stalkerpro_1_1+git92+9846d680+9846d68c94.ipk then command opkg install --force-depends /tmp/*.ipk and restart
-
Hello Ziko, when I try to access http://192.168.x.xxx/multi-stalkerpro/portals I get this error < Error 404: Not found >
What could be the cause of this error? Thank you!
-
Thanks Ziko
-
Hello Ziko, can you explain to us how to load srt from file? Thank you.
-
thanks for the reply seagen. does that mean I have to pull another cable from dish to 2 tuner on master stb? if so, I don't think it's possible, I only have one cable, it already makes diseqc on the dvb-s2x tuner. I don't think I can split a single cable into 2 tuners, the frequencies will be divided as well. anyway, thanks again.
-
Hi pauldb, Master stb has 2 tuners, Slave stb has 1 tuner. So, Master stb {Edition os mio plus 4k}, slave stb {Octagon SF8008 4k}. The settings in master stb are as follows: [Tuner 1] Dvb-s2x, Diseqc 1.1, 8 lnb. [Tuner2] Dvbs2 nothing connected. The settings in slave stb are the same as in master. {Diseqc 1.1, 8 lnb} I managed to connect the remote channel stream converter, I managed to load all the bouquets I was interested in and it works. The problem is that I don't see the channels separately, individually from stb to stb. Example: if I look at a channel [dazn1 bar stb master] I also see [dazn1 bar stb slave], the problem occurs when I change the channel. If I change the channel on stb master I can no longer see dazn1 bar on stb slave. Instead, I see all the channels on that Tp. I hope I expressed myself well. Thank you!
-
Hello everyone, my question is: why do I only see channels on the same Tp? Where am I wrong ? How can I show all channels {independently of each other} without putting Stb on standby? Thanks in advance and I hope to receive a little help from you.
-
I succeeded, I made a mistake in the DNS settings, it works perfectly! Thanks for the tutorial!
-
-
Regards Gorsky, first of all I want to thank you for the tutorial, it is very educational and auspicious for our protection, however, it does not work for me, I followed step by step everything that is written in the tutorial but does not want to connect. I mention that I have Enigma2 Pure2 Image v.6.3. What other options do I have? Thanks!
-
For gulli and tmc channels and a few other channels in the direction of astra 19 degrees, should this model be added or are they different?
use it
linuxsat-support.com/filebase/file/583/Hi, I don't see the download link, where is it?, thank you.
if you click on config the link will open.:rasta2bigsmoke0gf1:
-
Do I understand did the light at the end of the tunnel is finally visible?
-
To be honest, I had a lot of the range from Amiko (less viper) but ... I do not want to know about them anymore. Better put a penny on one side and buy a good receiver. I took Edision OS Mio 4K, is very good and makes good team with Enigma2 Pure2.
-
Advantage for Amiko Viper Combo 4K. It has a DVB-S2X tuner, if you like Enigma2. If you prefer Android, you can buy A5 or ... Maybe A6.
-
If you use Enigma 2 Pure2 image you will have the softcam.key updater plug-in
