Posts by cazuela

I would go as far as saying the most common Fline is F: xxxxx xxxxxx 2 0 0 { 0:0:2 } reason being that not many cards want to recieve emms from others and not many peers use hop3,unless there is a specific hard to get card..
Curious123 :
If the boxes are internal , intranet , then you only need F: xxxxx xxxxxx 3 0 0 { 0:0:1 } meaning that you use the main box( pc) as server then give a line out to each other box as clients,,so all will recieve from the main box/pc server only one hop down from the main server .
example: in main box/pc you recieve "xyzcard" in hop1 then you pass it on to your bedroom box it will recieve it in hop2 and so on down the chain hop2 in mainbox is recieved as hop3 in bedroom,etc..

The LNB in question was phased out a couple of years ago..the dish is still intact and workin perfectly,
but the braces are now discoloured and well faded .. if thats what you mean ¿¿¿???

¿ Tired of that automated high pitched whistle or BEEP when trying to find sats??
I did ,,so for the summer,I found an alternative,,

:40_002:

SUBJECT: Failure of the dish motor.

SYMPTOM: The LED motor lights but the dish/motor will not turn.

CAUSE: No power to the control circuitry.

EXPLANATION: For the antenna cable running from the decoder to the motor and dish are two signals, the high frequency of the LNB and feeding + / -15 (14/18)VDC feeds the control circuitry and the motor.
The two feeds are spread across the coil L1. This does not pass the high frequency signal (behaves like "open circuit" at high frequencies) but lets the DC no problem.
In this case, because moisture has entered the interior of the motor housing, the coil(bobina) has rusted. The rust has eaten up the copper up to cut the cord, preventing the passage of current to the control.

REPAIR: As we do not know the inductance of the coil, you can not buy a new one. We must repair the defective coil. The coil is cut by a loop near one end. Desoldering nearest end and remove the piece of copper excess, this means removing a few twists/turns, but functionally not affected. Solder the copper end (where it was cut) to pin the coil that is free ,check with the multimeter and you´ll find that between ends of the coil resistance is practically zero. Again the coil is soldered on the card. The engine will run correctly.
Before closing the casing ,there is a spray sold in most decent electrical stores that will "waterproof" the circuitry then seal with silicon the casing ensuring waterproofing ( in this case it was humidity not rain that caused the oxidation( rusting))
NOTE: this is only one possibility of motor failure.
BOBINA = COIL
This is the internal image of an ilusion motsat3 motor ( I imagine most are similar)

exactly ..with YES in an Fline ,there is no control over shares or distances....... in some cases up to 11 downhops...
If you add a YES in the cline you pass then the peer would be able to recieve EMMS from your card(hops)
As I understand it ..you have passed a Cline and your peer has passed ¿¿an Nline??
¿ Have you read any of the posts about Nlines in this forum?????? Not to sound too cautious but there is very little if none difference in ecm speeds,etc.. (as you say glitchfree) and Nlines are easily abused(not saying that this is the case) BUT have you paired up the fline to the host of the nline?? you´d be surprised by the amount of peers who simply don´t bother with minimal security..

merry-go-round

Quote from scoot1690

you could always put a piece of blutack on it and a piece of black tape over it mate

already suggested in post #5 by shamonemf ;;;)))

As new2 says, it´s not true whatsoever.. caminfo is only a "passive" reader..it cannot influence the server ,, but can confuse the peer if he/she becomes obsessed with updating it so often,,meaning the readings will always be different but thats all...

¿ can you encase it? meaning cover the front of the shelf with a plastic/glass sheet??either that or raise it over the tv.....

Educate the mommy to educate the baby not to touch Or lift it ( the box) out of reach of baby and mommy!!!
I imagine you are talking about the on/off button?? it would need unsoldering as I haven´t seen anything soft to disable it ,,will keep lookin!!

dreambox edit or dreamset are the progs to play around with..there are tuts on both,,use the search bar...
or if its raining and you have nothing else to do ,delete one by one....better than lookin at the rain ,i suppose!!

debian server has much more capacity so I can´t see why you should have any problems,
maybe somebody with experience with this could help you more with details, but I cant see why not..
of course you won´t be able to "duplicate" using the same peers in both at the same time.

Apart from all that has been said , have you turned the lnb clockwise/anticlockwise ? ¿have you revised the F connections to the cable??
have you updated the providors/channel list ??could be simply pids/frequencies are off (software) but sounds more like the dish/lnb isn´t correctly aligned..

I suppose you mean joining your 2 servers together in one debian server?? ¿ have you got different hosts? then I imagine different external IPs...
What doesnt make sense is that you have 45 servers yet only 19 clients :0:83::02:
I can´t see any relevance in whether your clients have 1 ,2 or 10 boxes unless they are all going to feed off your debian????= naturally the more connections to the server, more traffic you create....
Could you clarify a little more what you want to do exactly...

I have one too,but haven´t found anything "worthwhile" ... lets know if you do !!

Just got the infamous "watermark 7601" on w7 x64 bits ,,had noticed the net connections slowing down page opening..
this has been out since March 2011 apparently and here is the solution that worked for me :
write this in

CMD : BCDEDIT -SET LOADOPTIONS ENABLE_INTEGRITY_CHECKS
BCDEDIT -SET TESTSIGNING OFF

If you notice something failing to work then you can just do the same ending in:

CMD: BCDEDIT -SET LOADOPTIONS ENABLE_INTEGRITY_CHECKS
BCDEDIT -SET TESTSIGNING ON

I imagine ,like most recievers/images , there would be a default frequency,,but why not install a providors list/channel list and look for it then,, I think BBC world news, was about one of the strongest freqs..but like annie12 said you shouldnt have any probs dragging in the signal ,remember you have to bypass 19º before you get to 13º...
ah,,the pleasure of sat hunting ,few things can beat it ;)
good luck

the elevation is higher for 13º than 28º..remember from 0º it starts from highest point of arc ......so not just rotate dish from side to side but up a little also..
theres plenty of tuts to help you find it..

GM 4.70 :
SHOW TIMING : yes
MINI OSD : yes
ZAP OSD TIME : 3

unlimited reshare is limited by the card ..you can certainly reshare it as long as the cardholder permits you to... naturally the more users viewing the same channel at once will eventually drain the card saturating it with petitions and eventually cause glitching..