Posts by ahmed gazye
-
-
Dear brother / Worldcup
This is a very old version and the team has stopped supporting our devices i am have the latest version of the team for our devices
ViX4E2PROJECT-4.2-003-blue+-amikoalien_usb
-
My friend / BextrH
error Event
curls for my version
then
i Install curls from the menu
two appeared error
-
My friend / BextrH
Firstly, we thank you for this work
But we need more information, for example, is this applet for all devices or for specific devices for all copies or for specific copies The type of processor that plugin works on
I installed it and it was very easy to install
But it did not work with me to bring the servers and those are some error messages that appeared
Good luck
-
My friend / aa7590
Advice do not carry on the internal flash of the device, a developed copy, you do not know its source or belong to another device This happens many problems What is the type of your device so I guide you to a topic that solves you problem
-
Truman top box - spark sti 7162- rescue-image-1.2.65
First, remove any external flash that is installed on the device
Second, start with this solution and implement what is contained in it
Close the device from the power button in the back and Click on the ok from the front of the receiver for 5 seconds, then not leave ok, and
open the device from power button in the back,Until it Appears on the screen is forc supported you from Ok, then you Click on the channel buttons next to it until the word spark appears on the Ok wait a little while Boot appears and the device will run.
As it did not respond So it needs a suitable rescue soft
This file was presented by the professor master G
Follow the steps carefully and try more than once Do not give up
- Now another important factor is when using the rescue image, you must use the rear USB port, not the front.
- CREATE a folder on your desktop and call it spark
- UNZIP the spark rescue image.
- UNZIP userfsub.img.tar.gz & “mImage.tar.gz files.
- Now place the "mImage" and the "userfsub.img" files into the "spark" folder (Not userfsub.img.tar.gz & “mImage.tar.gz).
- FORMAT your USB Pen Drive in FAT32, DO NOT choose the quick format as it will not work
- TRANSFER the "spark" folder onto the USB Pen Drive
- SWITCH off the receiver at the rear and insert the USB Pen Drive
- PRESS and HOLD the OK key at the front of the receiver and switch it back on at the rear
- FORC will appear on the display after a couple of seconds
- PRESS the RIGHT key FACT should appear on the display
- PRESS OK key
- YOU should now see U LD flashing on the display
- WAIT a good 10 Minutes for the receiver to be back to original factory state (some information on the internet claims that the restore process takes about five minutes, I left mine a bit longer and it worked, so be patient)
Added to our supervisor's professor master G comments above
- Rescue Soft must be installed while you are on the Spark system, not a system enigma2 Until it is accepted
- It is possible not to accept Soft Rescue from the first times, meaning that you repeat the process once, two and three until it ends and the receiver accepts the software even if it did not succeed. Download another copy of Softrescue until you succeed, God willing,
Files
-
GI Russia_1.2.65_rescue_image_UpRachidcool77- spark7111& 1.2.73
First, remove any external flash that is installed on the device
Second, start with this solution and implement what is contained in it
Close the device from the power button in the back and Click on the ok from the front of the receiver for 5 seconds, then not leave ok, and
open the device from power button in the back,Until it Appears on the screen is forc supported you from Ok, then you Click on the channel buttons next to it until the word spark appears on the Ok wait a little while Boot appears and the device will run.
As it did not respond So it needs a suitable rescue soft
This file was presented by the professor master G
Follow the steps carefully and try more than once Do not give up
- Now another important factor is when using the rescue image, you must use the rear USB port, not the front.
- CREATE a folder on your desktop and call it spark
- UNZIP the spark rescue image.
- UNZIP userfsub.img.tar.gz & “mImage.tar.gz files.
- Now place the "mImage" and the "userfsub.img" files into the "spark" folder (Not userfsub.img.tar.gz & “mImage.tar.gz).
- FORMAT your USB Pen Drive in FAT32, DO NOT choose the quick format as it will not work
- TRANSFER the "spark" folder onto the USB Pen Drive
- SWITCH off the receiver at the rear and insert the USB Pen Drive
- PRESS and HOLD the OK key at the front of the receiver and switch it back on at the rear
- FORC will appear on the display after a couple of seconds
- PRESS the RIGHT key FACT should appear on the display
- PRESS OK key
- YOU should now see U LD flashing on the display
- WAIT a good 10 Minutes for the receiver to be back to original factory state (some information on the internet claims that the restore process takes about five minutes, I left mine a bit longer and it worked, so be patient)
Added to our supervisor's professor master G comments above
- Rescue Soft must be installed while you are on the Spark system, not a system enigma2 Until it is accepted
- It is possible not to accept Soft Rescue from the first times, meaning that you repeat the process once, two and three until it ends and the receiver accepts the software even if it did not succeed. Download another copy of Softrescue until you succeed, God willing,
-
Truman primier 1+ spark sti 7111- rescue-image-1.2.65
First, remove any external flash that is installed on the device
Second, start with this solution and implement what is contained in it
Close the device from the power button in the back and Click on the ok from the front of the receiver for 5 seconds, then not leave ok, and
open the device from power button in the back,Until it Appears on the screen is forc supported you from Ok, then you Click on the channel buttons next to it until the word spark appears on the Ok wait a little while Boot appears and the device will run.
As it did not respond So it needs a suitable rescue soft
This file was presented by the professor master G
Follow the steps carefully and try more than once Do not give up
- Now another important factor is when using the rescue image, you must use the rear USB port, not the front.
- CREATE a folder on your desktop and call it spark
- UNZIP the spark rescue image.
- UNZIP userfsub.img.tar.gz & “mImage.tar.gz files.
- Now place the "mImage" and the "userfsub.img" files into the "spark" folder (Not userfsub.img.tar.gz & “mImage.tar.gz).
- FORMAT your USB Pen Drive in FAT32, DO NOT choose the quick format as it will not work
- TRANSFER the "spark" folder onto the USB Pen Drive
- SWITCH off the receiver at the rear and insert the USB Pen Drive
- PRESS and HOLD the OK key at the front of the receiver and switch it back on at the rear
- FORC will appear on the display after a couple of seconds
- PRESS the RIGHT key FACT should appear on the display
- PRESS OK key
- YOU should now see U LD flashing on the display
- WAIT a good 10 Minutes for the receiver to be back to original factory state (some information on the internet claims that the restore process takes about five minutes, I left mine a bit longer and it worked, so be patient)
Added to our supervisor's professor master G comments above
- Rescue Soft must be installed while you are on the Spark system, not a system enigma2 Until it is accepted
- It is possible not to accept Soft Rescue from the first times, meaning that you repeat the process once, two and three until it ends and the receiver accepts the software even if it did not succeed. Download another copy of Softrescue until you succeed, God willing,
-
-
Dear Friend / gorski
The two methods are similar With little difference, as they unzip Image and load the Enigma2 file
in Spark System by load it in usb to the device & use a plugin_e2upgrade.s to install the Image.
Then Cross over it from the system >bisic setting >factory defauit > boot to E2
Possible risks are download Software for a different processor Can be treated by rescue_image
Good luck -
Dear Friend / gorski
Generally, your team version one of the best Images currently
I suggest increasing the discussion to include the internal flash of the Receivers This is just a suggestion if you like it
Good luck
-
Dear bro. / Worldcup
You can install enigma2-plugin-extensions-e2iplayer from the topic of the professor / enigma1969
On the following link
E2iPlayer aka IPTVPlayer plugin - DOWNLOAD ONLY DO NOT POST QUESTIONSIn order to work Well, your copy must have / ffmpeg
If you do not have it, you can download it from the feed link by the following commands telnet
opkg update
opkg upgrade
opkg install ffmpeg
Good luck
-
Truman_Spark7162_U-Boot & u-boot 131-11 for spark Truman sti 7111
Advice when using U-boot in spark boxs
Of course Some understood the U-boot wrong
The U-boot is used if the device is completely dead and passed through the JTAG
Then the device takes off on the boot mode, and then it can be resurrected with soft-rescue a suitable one soft rescue 7111 or 7162 Depending on your processor
Most of the brothers whose devices stopped on boot They updated the U-boot this is a mistake
As long as the device appears on the screen of the device Boot meaning that the device originally does not lose the U-boot or boot loader it is the Valid
And the device does not lose the U-boot or boot loader without the result of damage to the flash or charging the flash with a different dump
Use at your own risk!
-
-
Truman top box 7162 _rescue_image 1.2.58
First, remove any external flash that is installed on the device
Second, start with this solution and implement what is contained in it
Close the device from the power button in the back and Click on the ok from the front of the receiver for 5 seconds, then not leave ok, and
open the device from power button in the back,Until it Appears on the screen is forc supported you from Ok, then you Click on the channel buttons next to it until the word spark appears on the Ok wait a little while Boot appears and the device will run.
As it did not respond So it needs a suitable rescue soft
This file was presented by the professor master G
Follow the steps carefully and try more than once Do not give up
- Now another important factor is when using the rescue image, you must use the rear USB port, not the front.
- CREATE a folder on your desktop and call it spark
- UNZIP the spark rescue image.
- UNZIP userfsub.img.tar.gz & “mImage.tar.gz files.
- Now place the "mImage" and the "userfsub.img" files into the "spark" folder (Not userfsub.img.tar.gz & “mImage.tar.gz).
- FORMAT your USB Pen Drive in FAT32, DO NOT choose the quick format as it will not work
- TRANSFER the "spark" folder onto the USB Pen Drive
- SWITCH off the receiver at the rear and insert the USB Pen Drive
- PRESS and HOLD the OK key at the front of the receiver and switch it back on at the rear
- FORC will appear on the display after a couple of seconds
- PRESS the RIGHT key FACT should appear on the display
- PRESS OK key
- YOU should now see U LD flashing on the display
- WAIT a good 10 Minutes for the receiver to be back to original factory state (some information on the internet claims that the restore process takes about five minutes, I left mine a bit longer and it worked, so be patient)
Added to our supervisor's professor master G comments above
- Rescue Soft must be installed while you are on the Spark system, not a system enigma2 Until it is accepted
- It is possible not to accept Soft Rescue from the first times, meaning that you repeat the process once, two and three until it ends and the receiver accepts the software even if it did not succeed. Download another copy of Softrescue until you succeed, God willing,
-
Dear friends
Please note that a daily update of this version is issued by the team, the last of which was yesterday 9/3/2020
Good luck
-
spark7162_GI Russia_1.2.65_rescue_image_UpRachidcool77
First, remove any external flash that is installed on the device
Second, start with this solution and implement what is contained in it
Close the device from the power button in the back and Click on the ok from the front of the receiver for 5 seconds, then not leave ok, and
open the device from power button in the back,Until it Appears on the screen is forc supported you from Ok, then you Click on the channel buttons next to it until the word spark appears on the Ok wait a little while Boot appears and the device will run.
As it did not respond So it needs a suitable rescue soft
This file was presented by the professor master G
Follow the steps carefully and try more than once Do not give up
- Now another important factor is when using the rescue image, you must use the rear USB port, not the front.
- CREATE a folder on your desktop and call it spark
- UNZIP the spark rescue image.
- UNZIP userfsub.img.tar.gz & “mImage.tar.gz files.
- Now place the "mImage" and the "userfsub.img" files into the "spark" folder (Not userfsub.img.tar.gz & “mImage.tar.gz).
- FORMAT your USB Pen Drive in FAT32, DO NOT choose the quick format as it will not work
- TRANSFER the "spark" folder onto the USB Pen Drive
- SWITCH off the receiver at the rear and insert the USB Pen Drive
- PRESS and HOLD the OK key at the front of the receiver and switch it back on at the rear
- FORC will appear on the display after a couple of seconds
- PRESS the RIGHT key FACT should appear on the display
- PRESS OK key
- YOU should now see U LD flashing on the display
- WAIT a good 10 Minutes for the receiver to be back to original factory state (some information on the internet claims that the restore process takes about five minutes, I left mine a bit longer and it worked, so be patient)
Added to our supervisor's professor master G comments above
- Rescue Soft must be installed while you are on the Spark system, not a system enigma2 Until it is accepted
- It is possible not to accept Soft Rescue from the first times, meaning that you repeat the process once, two and three until it ends and the receiver accepts the software even if it did not succeed. Download another copy of Softrescue until you succeed, God willing,
-
The latest released of Spark devices for amiko8900 - purE2-6.3
The new released as 09/ 03 /2020
Download from offiaial website ...
http://pur-e2.club/OU/images/index.php?dir=6.3/fulan/
PurE2-6.3
user = root
password = pure2
-
Latest released of Spark devices sti7162 for amikoalien-PurE2-6.3
The new released as at 09 /03/2020
Download from official website ...
http://pur-e2.club/OU/images/index.php?dir=6.3/fulan/
PurE2-6.3
user = root
password = pure2 -
My friend / hooka9999
Was the previous version deleted? by plugin WLTool.v02 before the installation and was the installation successful and the message appeared to you that the installation was successful the version has no problems and was previously installed by members of the forum try and did it happen before that when installing the previous versions or is it new you can install a copy Other for another team to try to find out if this problem is general to the device or it is specific to this version
Good luck
