My friends
new Spark devices sti7111 for amiko8900-PurE2-6.5 for test as at 6/3/2020
Download from official website ...
http://www.pur-e2.club/OU/imag…ex.php?dir=6.5test/fulan/
Good luck
Posts by ahmed gazye
-
new Spark devices sti7111 for amiko8900-PurE2-6.5 for test as at 6/3/2020
-
My friends
new Spark devices sti7162 for amikoalien-PurE2-6.5 for test as at 6/3/2020
Download from official website ...
http://www.pur-e2.club/OU/imag…ex.php?dir=6.5test/fulan/
Good luck
-
GM_Spark_990_Reloaded-Rescue-Image.1.2.65 for sti 7111
First, remove any external flash that is installed on the device
Second, start with this solution and implement what is contained in it
Close the device from the power button in the back and Click on the ok from the front of the receiver for 5 seconds, then not leave ok, and
open the device from power button in the back,Until it Appears on the screen is forc supported you from Ok, then you Click on the channel buttons next to it until the word spark appears on the Ok wait a little while Boot appears and the device will run.
As it did not respond So it needs a suitable rescue soft
This file was presented by the professor master G
Follow the steps carefully and try more than once Do not give up
- Now another important factor is when using the rescue image, you must use the rear USB port, not the front.
- CREATE a folder on your desktop and call it spark
- UNZIP the spark rescue image.
- UNZIP userfsub.img.tar.gz & “mImage.tar.gz files.
- Now place the "mImage" and the "userfsub.img" files into the "spark" folder (Not userfsub.img.tar.gz & “mImage.tar.gz).
- FORMAT your USB Pen Drive in FAT32, DO NOT choose the quick format as it will not work
- TRANSFER the "spark" folder onto the USB Pen Drive
- SWITCH off the receiver at the rear and insert the USB Pen Drive
- PRESS and HOLD the OK key at the front of the receiver and switch it back on at the rear
- FORC will appear on the display after a couple of seconds
- PRESS the RIGHT key FACT should appear on the display
- PRESS OK key
- YOU should now see U LD flashing on the display
- WAIT a good 10 Minutes for the receiver to be back to original factory state (some information on the internet claims that the restore process takes about five minutes, I left mine a bit longer and it worked, so be patient)
Added to our supervisor's professor master G comments above
- Rescue Soft must be installed while you are on the Spark system, not a system enigma2 Until it is accepted
- It is possible not to accept Soft Rescue from the first times, meaning that you repeat the process once, two and three until it ends and the receiver accepts the software even if it did not succeed. Download another copy of Softrescue until you succeed, God willing,
When the installation is complete, you can download the latest softwares from the forum to the your device
-
AMIKO_ALIEN2_1.2.83_app for spark sti 7162
This is an old version, Not available for many
use kingston or sandisk usb 4 or 8 GB
Make sure that the folder is not inside another folder, and there is no any Foldr it except Foldr plugin only.
After unzip the attached file, transfer the file to the usb and place it in the device. & so on as you Learn to install
-
My friends / amrsalah45
The image works without problems with the Video as you see the image from my device
After unzip the attached file mytest
Delete the first file mytest From the device , then transfer the new file mytest , then restart the device
the path / usr / lib / enigma2 / python
If the method does not work, reinstall the copy again
-
Orginal-Firmware 1.2.83 für den Amiko SHD-8900 Alien for spark sti 7111
This is an old version, Not available for many
use kingston or sandisk usb 4 or 8 GB
Make sure that the folder is not inside another folder, and there is no any Foldr it except Foldr plugin only.
After unzip the attached file, transfer the file to the usb and place it in the device. & so on as you Learn to install
-
My friend / Octa8on
After unzip the file,move it by program dcc
To the extension var / emu or user / emu & gave emu Authorization 755
Good luck
-
spark_rescue_image_Amiko_Alien2_v1.2.65 for sti 7162
First, remove any external flash that is installed on the device
Second, start with this solution and implement what is contained in it
Close the device from the power button in the back and Click on the ok from the front of the receiver for 5 seconds, then not leave ok, and
open the device from power button in the back,Until it Appears on the screen is forc supported you from Ok, then you Click on the channel buttons next to it until the word spark appears on the Ok wait a little while Boot appears and the device will run.
As it did not respond So it needs a suitable rescue soft
This file was presented by the professor master G
Follow the steps carefully and try more than once Do not give up
- Now another important factor is when using the rescue image, you must use the rear USB port, not the front.
- CREATE a folder on your desktop and call it spark
- UNZIP the spark rescue image.
- UNZIP userfsub.img.tar.gz & “mImage.tar.gz files.
- Now place the "mImage" and the "userfsub.img" files into the "spark" folder (Not userfsub.img.tar.gz & “mImage.tar.gz).
- FORMAT your USB Pen Drive in FAT32, DO NOT choose the quick format as it will not work
- TRANSFER the "spark" folder onto the USB Pen Drive
- SWITCH off the receiver at the rear and insert the USB Pen Drive
- PRESS and HOLD the OK key at the front of the receiver and switch it back on at the rear
- FORC will appear on the display after a couple of seconds
- PRESS the RIGHT key FACT should appear on the display
- PRESS OK key
- YOU should now see U LD flashing on the display
- WAIT a good 10 Minutes for the receiver to be back to original factory state (some information on the internet claims that the restore process takes about five minutes, I left mine a bit longer and it worked, so be patient)
Added to our supervisor's professor master G comments above
- Rescue Soft must be installed while you are on the Spark system, not a system enigma2 Until it is accepted
- It is possible not to accept Soft Rescue from the first times, meaning that you repeat the process once, two and three until it ends and the receiver accepts the software even if it did not succeed. Download another copy of Softrescue until you succeed, God willing,
-
Dear Friend / amrsalah45
I will search for an appropriate way to this problem, God willing, you know that I have a lot of copies just try the copy to install before making a topic for it so that it does not represent a problem for friends then leave it and do not work on it as time is limited with me
A temporary solution, I know that you work on the external flash, cross over to it from any copy on the external flash, add what you like, then go back to it and work
-
-
openvix-5.4.000.release-sparkreloaded_usb for spark 7111 & can used in 7162 built by ahmedmoselhi (great pain)
In the beginning The owners of the Spark devices must give thanks and greetings to Professor / Ahmed Moselhi and Like him because they
give us copies we did not expect to work on our devices because the teams of these copies stopped supporting our devices and if their expertise And their courage we would not be working on these copies
Note that the team does not support Spark devices
This is not an official version . There is no feed.
A raw versionThe image was built on 7/3/2020 built by ahmedmoselhi (great pain)
our thanks and appreciation For you
The version is dedicated to the 7111 processor you can set on the external flash & internal flash
plugin NFR4XBoot or plugin imagemanager
But suitable for processor 7162 as you will see later
The version works both internally and externally flash with the following in mind
First / the version is large in size and it is raw with additions. It will increase the size and fill the internal flash completely and will become heavy while dealing with it.
Secondly / a general rule. It is desirable that the installation of the developed versions and not the original on the external flash be protected for the device because it is less good in construction than the original version because the developed version is usually built by an individual. The original is built by a team with great experience.
For the owners of the processor 7162 You can install the copies on your device On external flash only by Nvr4X Multiboot
the developer making a single copy of processor 7111 accordingly you can use it as stated in my topic
Pictures from my machine which processor 7162
-
Dear Friend / gorski
he is supervisor's in Forum
Registration to the forum is extremely difficult it use for the Russian language
Good luck
-
alien2.u-boot.S25FL016A.bin
Advice when using U-boot in spark boxs
Of course Some understood the U-boot wrong
The U-boot is used if the device is completely dead and passed through the JTAG
Then the device takes off on the boot mode, and then it can be resurrected with soft-rescue a suitable one soft rescue 7111 or 7162 Depending on your processor
Most of the brothers whose devices stopped on boot They updated the U-boot this is a mistake
As long as the device appears on the screen of the device Boot meaning that the device originally does not lose the U-boot or boot loader it is the Valid
And the device does not lose the U-boot or boot loader without the result of damage to the flash or charging the flash with a different dump
Use at your own risk!
-
GM_Spark_ONE_Triplex_Rescue-image_1.2.65 for sti 7162
First, remove any external flash that is installed on the device
Second, start with this solution and implement what is contained in it
Close the device from the power button in the back and Click on the ok from the front of the receiver for 5 seconds, then not leave ok, and
open the device from power button in the back,Until it Appears on the screen is forc supported you from Ok, then you Click on the channel buttons next to it until the word spark appears on the Ok wait a little while Boot appears and the device will run.
As it did not respond So it needs a suitable rescue soft
This file was presented by the professor master G
Follow the steps carefully and try more than once Do not give up
- Now another important factor is when using the rescue image, you must use the rear USB port, not the front.
- CREATE a folder on your desktop and call it spark
- UNZIP the spark rescue image.
- UNZIP userfsub.img.tar.gz & “mImage.tar.gz files.
- Now place the "mImage" and the "userfsub.img" files into the "spark" folder (Not userfsub.img.tar.gz & “mImage.tar.gz).
- FORMAT your USB Pen Drive in FAT32, DO NOT choose the quick format as it will not work
- TRANSFER the "spark" folder onto the USB Pen Drive
- SWITCH off the receiver at the rear and insert the USB Pen Drive
- PRESS and HOLD the OK key at the front of the receiver and switch it back on at the rear
- FORC will appear on the display after a couple of seconds
- PRESS the RIGHT key FACT should appear on the display
- PRESS OK key
- YOU should now see U LD flashing on the display
- WAIT a good 10 Minutes for the receiver to be back to original factory state (some information on the internet claims that the restore process takes about five minutes, I left mine a bit longer and it worked, so be patient)
Added to our supervisor's professor master G comments above
- Rescue Soft must be installed while you are on the Spark system, not a system enigma2 Until it is accepted
- It is possible not to accept Soft Rescue from the first times, meaning that you repeat the process once, two and three until it ends and the receiver accepts the software even if it did not succeed. Download another copy of Softrescue until you succeed, God willing,
-
spark_rescue_image_Amiko_SHD-8900_v1.2.65 for sti 7111
First, remove any external flash that is installed on the device
Second, start with this solution and implement what is contained in it
Close the device from the power button in the back and Click on the ok from the front of the receiver for 5 seconds, then not leave ok, and
open the device from power button in the back,Until it Appears on the screen is forc supported you from Ok, then you Click on the channel buttons next to it until the word spark appears on the Ok wait a little while Boot appears and the device will run.
As it did not respond So it needs a suitable rescue soft
This file was presented by the professor master G
Follow the steps carefully and try more than once Do not give up
- Now another important factor is when using the rescue image, you must use the rear USB port, not the front.
- CREATE a folder on your desktop and call it spark
- UNZIP the spark rescue image.
- UNZIP userfsub.img.tar.gz & “mImage.tar.gz files.
- Now place the "mImage" and the "userfsub.img" files into the "spark" folder (Not userfsub.img.tar.gz & “mImage.tar.gz).
- FORMAT your USB Pen Drive in FAT32, DO NOT choose the quick format as it will not work
- TRANSFER the "spark" folder onto the USB Pen Drive
- SWITCH off the receiver at the rear and insert the USB Pen Drive
- PRESS and HOLD the OK key at the front of the receiver and switch it back on at the rear
- FORC will appear on the display after a couple of seconds
- PRESS the RIGHT key FACT should appear on the display
- PRESS OK key
- YOU should now see U LD flashing on the display
- WAIT a good 10 Minutes for the receiver to be back to original factory state (some information on the internet claims that the restore process takes about five minutes, I left mine a bit longer and it worked, so be patient)
Added to our supervisor's professor master G comments above
- Rescue Soft must be installed while you are on the Spark system, not a system enigma2 Until it is accepted
- It is possible not to accept Soft Rescue from the first times, meaning that you repeat the process once, two and three until it ends and the receiver accepts the software even if it did not succeed. Download another copy of Softrescue until you succeed, God willing,
-
Amiko SHD-8900 Alien U-Boot 1.3.1 (Oct 19 2010 - 180850)
Advice when using U-boot in spark boxs
Of course Some understood the U-boot wrong
The U-boot is used if the device is completely dead and passed through the JTAG
Then the device takes off on the boot mode, and then it can be resurrected with soft-rescue a suitable one soft rescue 7111 or 7162 Depending on your processor
Most of the brothers whose devices stopped on boot They updated the U-boot this is a mistake
As long as the device appears on the screen of the device Boot meaning that the device originally does not lose the U-boot or boot loader it is the Valid
And the device does not lose the U-boot or boot loader without the result of damage to the flash or charging the flash with a different dump
Use at your own risk!
These are the instructions for the programmer
Emergency HowTo: Overwrite boot loader
=======================================
Use only in an emergency!
- Switch off the box, then connect to a PC / laptop using a null modem cable (RS232)
- Start HyperTerminal and create a new connection
-> select correct Com interface
-> Bits per second: 115 200
-> Flow control: none
- Then transfer> send file
- choose correct uboot-xxx.bin
- Protocol: Ymodem
- Click send!
> now switch on the box!
- When switching on, keep the [OK] key pressed until [FORC] appears
- then press the left arrow key [<]
- R232 appears on the display
Now the transmission takes place, which should take about 2 minutes.
Under no circumstances switch off prematurely or other maneuvers in this phase!
LG
Googgi
-
Dear Friend / gorski
First, we thank you for this addition to my humble topic, which is the addition of professionals. You are One of the members PurE2 Team and you are professional but I'm still a beginner trying to learn.
The addition came in a professional form, unlike my humble explanation and my weak English language.
But not all recipients or followers of the topic are professionals and they have full knowledge of the professional language.
Some expressions may not be clear to them.
Many have followed it objective and have succeeded in working with its modest content
In general, we thank you for this addition, as the topic has become more beautiful and clear to all those who follow him,
Good luck
-
Dear Friend / gorski
My dear friend, there are no Thank you between friends.. This is a duty we all listen and learn from each other. Opinion and advice are important in our lives i are still Beginner and learn I am not a professional like you....
This is another program for dividing the flash Admin_Tool_Morly . This section is called Swap fat 32
-
Dear Friend / gorski
I did not call this name the programs that divide the flash it calls it Should Format fat 32
SWAP is a Linux system
I work on 2 external flashes for each flash Everyone has a Partition SWAP or a Linux system
Otherwise, the flash did not work
-
Dear Friend / gorski
This is another program for dividing the flash cteate mini . This section is called Swap fat 32
