Posts by rhinoranger

you can enter a Newcamd or CCcam line manually

hello.i loaded that same firmware yesterday and could not get the 9991 menu,BUT i have just this minute sussed out if the MENU button is pressed before entering 9991 the server details appear,("menu THEN 9991") the server stuff appears,i have a blade combo 8000 and a blade 7000s and 7000combo before that so i was always going for 9991 input straightaway,i cannot believe it was that simple, i hope it will save somebodys head being done in,thanks

hello recently bought the blade neo satellite receiver loaded firmware but still no 9991 option,i've been told that i might want a config file loading anybody know were there is the config file for the blade neo,any help appreciated

- - - Updated - - -

hello.i loaded that same firmware yesterday and could not get the 9991 menu,BUT i have just this minute sussed out if the MENU button is pressed before entering 9991 the server details appear,("menu THEN 9991") the server stuff appears,i have a blade combo 8000 and a blade 7000s and 7000combo before that so i was always going for 9991 input straightaway,i cannot believe it was that simple, i hope it will save somebodys head being done in,thanks

hello,i have ordered the ariva 153 and downloaded the 153 'patch',could you please tell me when i load the patch do i use the all ("software + bootloader ") option i'm only guessing the box has this option also could you please tell me how i 'back up' the channel list from the 153,is there a usb dump on the menu,any help appreciated

ok thanks for the reply, mgcamd will be ok,thanks again for the info, appreciated

hello very grateful for the reply,could you please tell me if the oscam emu is also on the patch for the 153, thanks

hello,can anybody please tell me if the ferguson 153 will work ok on the United Kingdom cable channels and does the 153 have the mgcamd emu and can the ( lines ) be entered manually with the remote control,also i have spotted some firmware for the 153 on the forum does the firmware have the emulator,any help will be appreciated

hello, i have just bought an amiko impulse cable receiver and i am having difficulty in connecting it on wifi, in the ethernet menu on the impulse there is a section called -: (pptp vpn settings) in there it has places for username and password which i have entered from the router, in another section on the ethernet menu there is a section called -: ("ap connect") in there there is -: network ssid-> signal level ->encrypt mode->ipv4 address->key->show key ")there is only key that anything can be entered so i have entered everything that is written on my router numbers ect but no joy with connection, the amiko is pickin up the signal from my router cos it shows around the 80% signal strength and on the ssid it states my suppliers name,i have entered different things thats on my router but when i scroll and press for connection no joy,any help that can be given to me would be greatly appreciated,thanks

hello, i am about to buy amiko Full HD Compact Size Digital T2 Terrestrial / Cable Receiver & Media Player,could anyone please tell me what firmware i need to load onto the receiver to enable me to enter C or N lines from server,any help appreciated

the DR D15 was new out of the box,there was power on the box till i loaded the firmware that i put in the reply earlier,after i loaded the firmware there was no power,if its not called bricked what should we call it ? any suggestions f*cked maybe ?

hello, i have tried what you have written but there is no power coming on the box

hello, thanks for the reply, i got the the firmware from a deiseldo "information" thread the firmware was posted by digi 247 on the 10-12-2012 in DR D15 (support) can you tell me how do i load the firmware you recommend onto a dead box through the RS232 port ---- -:
Following on from my previous post you are in luck the Patched firmware for the D15 has now been released, I am unsure if you need to flash the Module_002p as well as my Grand triple has everything built into the main patch. But this could be sue to the size for the F15 the firmware patches where around 5mb the Grand triple are around 60mb.

Anyway here it is please let us know how you get on.

Regards

Attached FilesD15_wifi_101p.rar (3.67 MB, 73 views)

i loaded the D15_wifi_101.stb file from this site ,the box is now bricked

hello, i have downloaded the D15_wifi_101.stb file for the (press green button) and CCcam and newcamd line entry could any
one please tell me how i load the file onto the box,any help appreciated

hello,diesldo did you load the file via usb,thanks in advance for any reply

hello, i am thinkin of buying the DRHD-15 and i have read that the receiver has ("Upscale function for viewing of normal SD channels upscaled up to 1920x1080p") is that correct guys,because i am on s*y UK and the HD channels have gone awol, is the picture that good ! ! !,any opinions valued and appreciated

hello, can anyone please tell me how do i get an omnikey 3121 card reader working on the vu+solo,any help appreciated

in my humble opinion if you want a cheap reliable sat receiver a ***box F3 is the one if you want to pay out a bit more for a bit of decent quality a blade 7000s would be my choice

hello, can you tell me if there is a loader for the 'rom reset' file so i can load it through the rs232 port as i cannot gain entry to the usb on the menu,thanks

hello, i could not my eagle 800 box to connect with cccam tried it on test and and said success but still did not connect and i tried flashing with different firmware but ended with it being bricked, there is just a blue screen now no access to menu, is there any firmware i could flash it with through the rs232 port to bring it back to life,any help appreciated