Posts by Abdullahkhan.007

Quote from master G

oscam.keys & oscam.constant.cw are only used with oscamymod.

You get that error because oscam-emu doesn`t know what to do with the files or readers you added for oscamymod.

I removed these from your previous configs because they are not compatible with oscam-emu.

But for some reason you still decide to use your old configs ??

I never installed oscamymod. I am using the old configs because of my lack of experience and because I was scared that I might lose powervu channels if I changed anything in the keys folder.

So what can I do now to eliminate the problem?
What should I edit and of which file?

5d2dcb0c882473fcc5f.jpg

Can someone confirm that has the AFN package on 9 east changed its encryption from Power VU to another system? If not then kindly attach a screen shot of the channels so that I can learn the "prov" and "chid" as shown in the picture below because I think that something is wrong in my script.

If anyone of you has AFN Package of 9 east running on their enigma2 receivers so either paste its screen shots it in this thread or message it privately to me. I`ll be very thankful for your cooperation.

Thank you all in advance :)a86b1290b86b03bd81.jpg

Can someone help me who has 9 east on...???

Can someone point out where the problem is???c99f82923d565287de0.jpg

Can Someone for the love of God help me once...a7361b5c410cfaccd6.jpg

ec43cb.jpg

Can you paste a link in which the method for changing the keys is shown.

Help me only this time with AFN package. I will never ask about any kind of Power VU problem...
The keys keep on changing but no images are shown. What might be the problem? I tried to change the keys in a lot of ways but none worked.
16cefebc3dfb753eb7.jpg

Quote from master G

For CSA encrypted channels you don`t need stream relay.

For DES encrypted channels you need stream relay.

AFN uses DES encryption.

Use the drivers that joeuser has provided and you won``t need stream relay -> HDMU_16560_E2_spark_217_git_581 + HW DES Drivers

why is there /usr/libexec/keys/SoftCam.Key after SoftCam.Key?

Shouldn`t the script end on /usr/keys/keys/SoftCam.Key?

Stop making things difficult buddy.

Open the file Your-Softcam-Key-Location, remove anything thats inside and add this:

/usr/keys/SoftCam.Key

Now place the SoftCam.Key file in /usr/keys

simple.

Did what you said and the problem still remains...5902610a03e276f4.jpg

b00fc7232a82166f9bed9c09f.png

Quote from master G

Going from your screenshot the keys are correct, but the channel isn`t opening because you need to setup stream relay.

What is wrong with my stream relay?

I guess something is wrong with the script and that I need to write an id just underlined below so that the keys can be linked... Am I right?
e1db9e.png

You did not modify the Soft Cam file. Are all the keys mentioned for AFN 9.0 East alright? Why don`t the picture come, the keys change constantly but no picture comes.fd803c64e6aaca83c11cf3.jpg

A Friend of mine is asking this question:

"How to install latest cccam 332 version in Spark.sh4 i.e. Amiko Alien 2 ( Star Track 2020 HD+) for E2 for Open ATV 6.0.

He is saying that in our Spark boxes our latest version of cccam is 2.1.3 is it a modified version of .sh4?

He is asking that why haven`t any other latest version come for our
.sh4 boxes. Can we put the latest cccam file in .sh4 by changing the
script of cccam"

Quote from master G

I really hope you didn`t attach live server details (c line) in your last post.

If you did let me know, as i will need to put an example in your configs.

There were no c line in that files they were only given as an example.

Quote from master G

Keep it simple, only run OsCam-PowerVU.

Move the [reader] you have configured for CCcam into the oscam.server you are using for OsCam-PowerVU.

One version of oscam-emu running powervu and cccam at the same time.

Below is attached the .rar file in which are the files in the OsCam-PowerVU keys folder due to which the Power VU channels run. How can I put my c line in these files without disturbing the power vu channels.

And one thing more, the Cartoon channels that run on power vu on 105.5 east and the AFN package on 9 east do not run, some one told me that the cartoon channels of 105.5 east don`t run on Open ATV image. Is it true?

And why isn`t the AFN package being opened? I tried a lot but the AFN package doesn`t run, is there something wrong with these files? Can you check what script or setting is wrong in these files due to which the AFN package of 9 east and the Cartoon channels of 105.5 east don`t run.

And in the .rar file there are other cams too. Kindly remove all the cams that are not required other than for c line channels and power vu. As I am a newbie to enigma and my enigma knowledge is not that much.

Thank you in advance. :)

???

Awaiting your reply...

Quote from master G

By moving your configs from cam1 into cam2.

Then only running oscam-powervu

I didn`t get you.

Do you want me to only watch Power VU channels?

Quote from master G

Why the need for 2 versions of oscam-emu ?

One version should do everything you need.

How?

I have corrected the permissions but the problem now is that even though Softcam Panel V2.0 supports both the cams but the problem still is the same i.e. when I open a Power VU channel it runs flawlessly but when I switch back to a cccam channel it doesn`t play, I have to go to the Softcam Panel V2.0 and restart the oscam emu v9963 then the cccam channel plays.0c5c6f896987c413701be.jpg

How can I make both the cams work in a way that when I switch from power vu to cccam channels I do not have to go and restart the oscam emu v9963 to play the cccam channel again.

caf67.png

this is the script of the cam that is working i.e the cam in which I use cccam:

1.emuname = oscam emu v9963
2.binname = oscam_emu
3.startcam = /usr/bin/oscam_emu -b -r 2 -c /usr/keys/oscam_emu
4.stopcam = killall -9 oscam_emu

Did everything you said, it seems like the softcam panel is not accepting it, why might be the reason?

04e26119189.jpg

Quote from master G

It won`t until you put a script for it in /etc

You need a script named OsCam-PoweVU.emu in /etc with 755 permissions.

Contents of the script will be this:

Code

emuname = OsCam-PoweVU
binname = OsCam-PoweVU
startcam = /usr/bin/OsCam-PoweVU -c /usr/keys
stopcam = killall -9 OsCam-PoweVU

What does 755 permissions mean?

and should I write OsCam-PoweVU or PowerVU you haven`t written "r", is it deliberate?

Quote from master G

Quote from Abdullahkhan.007

show me where the folder or path is located so that I can put the other emulator in it

You can put the emulator anywhere you want.

Then tell the start/stop script where to look for it.

For example, you have ncam.sh4 in /usr/bin folder:

emuname = ncam_1.6
binname = ncam.sh4
startcam = /usr/bin/ncam.sh4 -c /usr/keys
stopcam = killall -9 ncam.sh4

Where is the start/stop script located?

I put the oscam-powervu emulator in /usr/bin but it did not show in the softcam panel V2.0. So what can I do to put the emulator in softcam panel 2.0 so that I can have both the oscam- power vu and oscam emulator in Softcam Panel 2.0?
c601e59.png

I have tried the alternate softcam manager and it worked but the problem is that I want my power vu channels to run on Softcam Panel 2.0 because there is an option of selecting 2 cams so in one cam I`ll put my c line and the other will run Power VU channels so whenever I change the channel from cline channels to power vu channels so they`ll run smoothly. Now I have to go and restart the cam in softcam panel 2.0 to start the c line channels when I change from power vu to c line channels.

Nowt the problem is that I can not find the folder or the path of softcam panel 2.0 so can you show me where the folder or path is located so that I can put the other emulator in it i.e in which to put the emulators like ncam or wicard, gcam and oscam etc.
I hope you got my question.

Quote from man-s2

oscam-ymodv1856-sh4
mgcamd1.38_srf.sh4

2fa143f619a2a6b52622c3a1.jpg

openatv

usr/bin/cam
var/keys

Display More

I`m using Open ATV 6.0 and "/usr/keys/oscam_emu" this is where my configuration files are there is no bin and cam and var folders in my Open ATV 6.0 image. So where should I put these "oscam-ymodv1856-sh4 mgcamd1.38_srf.sh4" files and where should I put the softcam file?

I am working on it since almost 12 hours straight and I also installed wicard but still no luck. Can you just pinpoint to what exactly is wrong because I know that 99% is right just point out the 1% so that I can finish this project and cross it off of my list.

I`ll be supremely thankful to you, just 1% help is required, just pin point me to what exactly should i do right.