Sorry for my english but what do you means for "an intro mate"? I was looking on google for a solution on my issue and I have found this forum. Unfortunately I don't know any one?
So If I can, I will try to explain every single detail.
I have two decoder:
* VU+ Ultimo with BH 1.7.4 (2 dvb-s, 1 dvb-t)
* ipbox910HD with Sifteam image r13736
On ipbox910 I have mgcamd 1.35 and oscam where all works well
2012/05/20 19:09:56 552F20 r >> OSCam << cardserver log switched, version 1.20-unstable_svn, build #5879 (sh4-amino-linux
2012/05/20 19:09:56 552F20 r version=1.20-unstable_svn, build #5879, system=sh4-amino-linux, nice=-1
2012/05/20 19:09:56 552F20 r client max. idle=120 sec, debug level=0
2012/05/20 19:09:56 552F20 r max. logsize=100 Kb, loghistorysize=4096 bytes
I have just buy VU+ and I'm tring to connect to oscam on ipbox.
I have these more information:
* PIP works well on two dvb-s channel not crypted (tuner should be correctly configured)
* mgcamd hang on fourth channel change; to restart viewing correctly the channel I need to restart mgcamd or BH GUI
* using mgcamd 1.35a or 1.38, I have the same issue.
* when I see the blank screen on VU+, on ipbox I have correct "found" key message
* when I have restart the BH GUI I had these message log on ipbox
2012/05/20 19:42:21 55A728 c user (***): found (103 ms) by ***italia (of 1 avail 1)
2012/05/20 19:42:23 555558 c user (***): found (106 ms) by ***italia (of 1 avail 1)
2012/05/20 19:42:33 555558 c user (***): found (103 ms) by ***italia (of 1 avail 1)
2012/05/20 19:42:43 555558 c user (***): found (104 ms) by ***italia (of 1 avail 1)
2012/05/20 19:42:44 55A728 c WARNING: invalid client tcp_conn_close()
2012/05/20 19:42:44 55A728 c user disconnected from 192.168.1.12
2012/05/20 19:42:44 55A728 c thread 2C6D94E8 ended!
2012/05/20 19:42:44 55EF60 c client connected to 11500 port
2012/05/20 19:42:44 55EF60 c encrypted newcamd:11500-client 192.168.1.12 granted (user, au=on (1 reader))
2012/05/20 19:42:44 55EF60 c user user authenticated successfully (mgcamd)
2012/05/20 19:42:44 55EF60 c AU enabled for user user on reader ***italia
2012/05/20 19:42:51 55EF60 c user (09CD&000000/0FD6/B7:38E1): found (108 ms) by ***italia (of 1 avail 1)
2012/05/20 19:42:53 555558 c user (***): found (102 ms) by ***italia (of 1 avail 1)
Display More
All the config files are these:
newcamd.list
CWS_KEEPALIVE = 300
CWS_INCOMING_PORT = 21000
CWS = 192.168.10.3 11500 user pass 01 02 03 04 05 06 07 08 09 10 11 12 13 14 lan server1
mg_cfg
# EMM messages
# 00 don't show any EMMs (default)
# 01 show only valid EMMs
# 02 show valid and bad EMMs with complete data display
M: { 00 }
# ECM messages
# 00 don't show anything about ecm
# 01 normal mode, show pids processed, decoded ecm and cw
# 02 verbose mode, show valid and bad ECMs with data
C: { 01 }
# AU
# 00 disable, no emm pids processed
# 01 enable, emm pids always processed for soft-au and shared cards
# 02 auto, emm started only if channel cant be decoded
# 03 process emm pids for network cards update only
A: { 00 }
# key update (sum 01 or 02 with 04)
# 01 update only new keys, default setting
# 02 update all keys (used for valid PMK checking)
# 04 enable TPS au
# + tps SID, which pmt pid contains au pid
U: { 02 } 0x12c0
# config files folder (softcam, autoroll, ignore/priority)
# 00 files in /var/keys
# 01 files in /tmp
T: { 00 }
# network mode, use summ for several clients
# 00 no network (default)
# 01 newcamd netclient
# 02 radegast netclient
# 04 camd3 netclient
# 08 gbox netclient
# 32 cccamd netclient, card list saved as /tmp/cccamd.info
# (ECM only, supported server version up to 2.1.1, later not work)
G: { 01 }
# network retry, use summ for several options
# 00 disable
# 01 retry every new ecm
# 02 try to connect to offline shares every Q: seconds
# 04 try to detect and fast reconnect to lost (and not used atm) server
# + XX messages number and YY seconds to reconnect
# mg will reconnect to server, if no answer to last XX ecm/keepalive or
# if no answer for last ecm or keepalive sent for YY seconds
# set to 0 to disable
N: { 07 } 360 3600
# network ecm timeout in seconds
K: { 07 }
# newcamd dead routes connect retry, sec
Q: { 60 }
# network shares priority
# 00 gbox, newcamd, cccamd, radegast, camd3 (default)
# 01 camd3, radegast, cccamd, gbox, newcamd
# 02 cccamd, newcamd, camd3, gbox, radegast
P: { 00 }
# on screen display type
# 00 No OSD (default)
# 01 neutrino
# 02 enigma
# 03 relook
# + user password for http auth
O: { 02 } root password
# on screen display Options, summ of:
# 01 show emu ecm
# 02 show network shares messages
# 04 show decoding failed / fta
# 08 show emm keys update
# + web port to use for osd
S: { 03 } 80
# Log option, summ of:
# 00 off
# 01 network udp log
# 02 log to console
# 04 file, appended ! delete it by yourself, before it eat all your hdd
# + IP udp-port log-file-name
L: { 02 } 172.16.1.1 28007 /tmp/mgcamd.log
# keep ecm cache, seconds
# every cache entry takes 28 bytes, so 24h cache will take *only* 240-400kb of memory,
# for openbox/elanvision users with remote shares make sense to set it higher than default value,
# to not hammer cards while timeshifting or playing crypted recordings.
E: { 00 }
# cache option, summ of:
# 00 Off (default)
# 01 Ecm pids cache, store pids used to decode in /tmp/ca_cache.list at exit, load at startup, same syntax as restore.list
# 02 Ecm data cache, remember CW for (E:) time
# 04 Emm cache for network cards, do not resend the same emm twice, cache not cleared until restart
H: { 00 }
# reread files, summ of:
# 00 No (default)
# 01 reread config file on channel change (including priority and ignore, but not replace/cache)
# 02 reread SoftCam.Key on channel change
# 04 reread SoftCam.Key if file changed
R: { 00 }
# debug, summ of
# 00 off (default)
# 01 debug ecm
# 02 debug emm
# 04 debug network ecm
# 08 debug network emm
# 16 debug network login
# 32 show mem/cpu stats every 1 min
# 64 add timestamp to log messages
D: { 31 }
# box type
# 00 autodetect, change only if you think wrong type detected.
# 01 dbox2
# 02 dreambox
# 03 triple-dragon
# 04 relook
# 05 openbox
# 06 dreambox/mips
# 08 stapi/kathrein
# 09 stapi/ipbox
# 11 stapi/openbox
B: { 00 }
# map all 180x nagra caids to 1801
# default is 01
F: { 00 }
Display More
oscam.conf
#
# main configuration
#
[global]
nice = -1
WaitForCards = 1
# logging
pidfile = /var/run/oscam.pid
logfile = /var/log/oscam/oscam.log
usrfile = /var/log/oscam/oscamuser.log
cwlogdir = /var/log/oscam/cw
#maxlogsize = kbytes
maxlogsize = 100
# monitor
[monitor]
port = 988
aulow = 120
monlevel = 0
# protocols
[newcamd]
key = 0102030405060708091011121314
port = 11500@09cd:000000
#key = 0102030405060708091011121314
#port = 34000@093b:000000
#[radegast]
#port = 20000
#user = user1
#allowed = 192.168.0.0-192.168.255.255
#[cs378x]
#port = 30000@0100:FFFFFF;30001@0200:FFF000,FFFF00;30002@0300:FFFFFF
#[gbox]
#password = password1
#maxdist = 4
#cardinfos = card.infos
#ignorelist = ignore.list
#onlineinfos = online.infos
#locals = 01000000,02000000,0300FFFF
#[serial]
#device = user2@/dev/ttyS0?delay=1&timeout=300
Display More
oscam.server
#
# reader configuration
#
# serial reader
[reader]
Label = ***Italia
Protocol = internal
Detect = CD
Device = /dev/sci0
group = 1
CAID = 09cd
BoxID = 11223344
#savenano = all
Customspeed = 0
EMMCache = 1,1,2
Fallback = 0
#blockua = 0
#blockga = 0
#blocksa = 0
AU = 0
#Enable = 1
#[reader]
#label = reader1
#protocol = mouse
#detect = CD
#device = /dev/ttyS0
#group = 1
#emmcache = 1,3,2
#services = services1
#caid = 0100
# USB serial reader
#[reader]
#label = reader2
#protocol = mouse
#detect = CD
#device = /dev/ttyUSB0
#aeskey = 000102030405060708090A0B0C0D0E0F
#group = 2
#emmcache = 1,3,2
#services = services2
#caid = 0200
# remote newcamd reader with fallback for group 1
#[reader]
#label = remote1
#protocol = newcamd
#key = 0102030405060708091011121314
#device = 192.168.0.2,66666
#account = login1,password1
#group = 1
#fallback = 1
# remote camd 3.78x reader with fallback for group 2
#[reader]
#label = remote2
#protocol = cs378x
#device = 192.168.0.3,23456
#account = login2,password2
#group = 2
#fallback = 1
# remote gbox reader
#[reader]
#label = remote3
#protocol = gbox
#device = 192.168.0.4,34567,45678
#account = login3,password3
#group = 3
#caid = 0300
Display More
oscam.user
#
# user configuration
#
# user for group 1 with Betacrypt tunnel, no monitoring, only one connection possible, AU enabled
[account]
user = user
pwd = pass
group = 1
uniq = 0
#caid = 093b
#ident = 093b:000000
caid = 09cd
ident = 09cd:000000
AU = ***Italia
monlevel = 0
#[account]
#user = user1
#pwd = password1
#monlevel = 0
#uniq = 1
#group = 1
#au = reader1
#services = services1
#betatunnel = 0300:0001:0100,0400.0005:0100
#ident = 0100:000000
#caid = 0100
# user for group 2 with monitor access, AU enabled
#[account]
#user = user2
#pwd = password2
#monlevel = 1
#uniq = 0
#group = 2
#au = reader2
#services = services2
#ident = 0200:000000
#caid = 0200
# user for group 2 without monitor access, AU disabled
#[account]
#user = user3
#pwd = password3
#group = 2
#services = services2
#ident = 0200:000000
#caid = 0200
# user for group 3 without monitor access, only one connection possible, AU disabled
#[account]
#user = user4
#pwd = password4
#monlevel = 0
#uniq = 1
#group = 3
#ident = 0300:000000
#caid = 0300
Display More