Posts by shoaib334

Quote from ahmed gazye

Add some new definitions

42e86.jpg

Enjoy & Good luck

Display More

thanks for reply

I tried all, but nothing working.

receiver showing error 'not suitable architecture' something like that

Quote from teak-won-do

please try this with FTP over telnet:

Code

opkg update
opkg install kernel-module-rtl8192cu

reboot

Thanks for reply,

but these code not working.

please help,

i tried below driver in open pli and open atv,

enigma2-plugin-drivers-network-usb-rtl8192eu_1.0-r0_all

it works in open atv but not work in open pli,

openatv kernel version is 3.12.1 and open pli kernel version is 3.6.0

pls. share kernel version for open pli 4.0 for this wifi dongle,

I need kernel 3.12.1 ipk for openpli 4.0, chipset bcm 7358

Thanks for reply,

Sorry my mistake i was using winrar to decompress when i used 7zip it works,

My wifi dongle still didn't work,

One more request,

pls. check below details, i need driver & kernel for this hardware/software,

USB wifi dongle

Description: Realtek RTL8192EU Wireless LAN 802.11n USB 2.0 Network Adapter(Realtek 802.11n NIC)

Device Type: Vendor Specific

Protocal Version: USB 2.10 <- Hint: This device can run faster when plugged to a USB3.0 port

Current Speed: High Speed

Max Current: 500mA

USB Device ID: VID = 0BDA PID = 818B

Serial Number: 1CBFCE0B80CC

Device Vendor: Realtek

Device Name: 802.11n NIC

Device Revision: 0200

Controller Part-Number: Unknown

I have solo pro v3 receiver detail attached

adeee459939f9c599.png

da0270f5094d850311b45640.png

Hi Brother,

downloads are corrupted,

can you please share again?

I need driver for RTL 8814 wifi usb dongle for open pli4.1,

Dear Master G,

which one is suitable for openvix image vu solo pro v3 receiver?

thanks in advance

Dear Master G,

How to watch powervu channels from Asiasat 105.5,

pls. send Powervu softcam and suggest,

how to run powervu channels.

thanks in advance.

Dear Master G,

Please give Oscam-Emu for (herobox vu solo pro v3) running on openvix image,

and suggestion how to put them in receiver using filezilla,

It will be very thankful to you.

thanks.

Thanks a lot master G,

now everything working fine.

thanks again.

Dear Master G,

I installed your given Ipk, and edit newcamd.list file with my cline detail (my host ip in place of 127.0.1.1, port with 10001, username in place of linuxsat1 and password with sopport1) in usr/keys in filezilla, and save the file, and start mgcamd_138c under softcam setup, its showing active,

and edit cccamd.list file with my active cline same as above,

but channels are not opening,

than i start filezilla to find mgcamd.log file in temp, there is no magcamd log file, only showing mgcamd.pid, mgshare.info and mgstat.info,

In mgshare.info it's showing

newcamd route 0000:username:Host IP:Port:unknown EMM OFF offline

pls. suggest whats wrong,

attached openvix image i m using, in herobox vu solo pro v3.

thanks in advance,

Thanks master G,

I will try and post working or not working,

i want to confirm,i need to edit only newcamd file with my cline detail under usr/keys in filezilla,

pls. correct me if i m wrong,

thanks.

Dear Master G,

Please provide mgcamd 138 ipk for openvix image,

i have herobox solo pro v3 receiver,

thanks in advance,

Anyone pls. help me.