Update.
After reflashing, rebuilding , reconfiguring without success I tried a couple of test lines from a different source and instant picture.
Been in touch with my lines supplier and awaiting a reply :rolleyes:
At least I have learnt something new regards cccam etc.
Many thanks for your help guys :thumbup::thumbup:
Im assuming you have the extra tuner module and showing tuners I & J . if so just configure the used inputs as if its a seperate tuner, I am using 2 motorised dishes with inverto unicable SCR JESS LNB's which gives me quite a few extra tuners but obviously these are confined to where the dish is pointing. Again im assuming your aiming a third dish at a different satellite so if so set the tuner up your connected to as a if its a different tuner to all the rest .
I will have a few goes at various things first. As it was working fine up until a couple of weeks ago im suspecting something is corrupted withing the flash. Unless there has been a radical change to all the CS worldwide that I missed . But thank you for the offer . :thumbup: I am using the cfg files from here with just my lines attached so unless the cfg files are not working which i doubt I am thinking its something within the python preventing the softcam to run .
hello good morning , if u want I can try to help u to fixed via team vieuwer ?? I am genuine helper in the forum .
Good morning, and thank you, how does the viewer work ?
Loaded up the CCCam and its connecting but still no pic , showing 61 cards per line , Im still edging towards a corrupted flash image . Again many thanks for the input guys it well appreciated . Ive tried a few channels on 28.2 and 23.5 but no pic , but the boss wants to watch stuff so im stuffed for messing at the min. Im using the red vix skin but dont think its the skin being the issue . Something is holding it back and ill get to the bottom hopefully. With a lot of guidance I think . :thumbup::thumbup: Appologies in advance for not posting an intro , Ive been around sat forums for years and should know better, ;)
Theres no cccam for the Arm processor only mips , so only oscam unfortunately , but thanks for answering
Still havinng no luck . just wondering wether a complete reflash of the openvix and start over may be the answer. The log shows connections and the CAIDs are now populated but still nowt on telly. Anyone any suggestions before I start over ? :/:/
have downloaded latest from vix but still no luck .. getting square eyed at moment from files so ill give it another go tomorrow.
Master G you a star for giving me the time . Its much appreciated . :thumbup::thumbup::thumbup::thumbup::thumbup:
oscam-11400 keeps disconecting and reconecting
Then download oscam from the openvix feed. Its tried and tested..
will do
for some reason the oscam-11400 keeps disconecting and reconecting then the " read user data from oscam.conf " reverts to "no" then asking for the usual username ( httpuser), pass (httpwd) ip-address 127.0.0.1 port screen ..
I have reloaded server file but lines keep changing from green to red and having to restart oscam ... head scratching time :/
only showing an empty log called samba in that directory
reloaded and installed ipk file, still same result . where is the log file located within the files, if i can edit the relevant out and print that it may be of help ?
I used file zilla to load softcam, just wondering is via usb may work .. I'll give it a try , just to be sure
Yes all fTA channels are ok from 28.2E to 30W both motorised dishes move idependant on FBC lnb's so i can rule out tuners . Everything was working up until 3 weeks back . I am routing through a vpn but always have been , even tried turning vpn off just in case but still nothing . Very frustrating as im running 2 clines and each shows connected with 61 cards apeice. just thinking about trying my VUsolo and see if it works on that . or is it the VIX platform needs reloading .. :(
the log and server id are showing that the CAID:SvrID 0000:0000 in both log and clines. There are other logs but nothing that i havent seen before. Normally the CAID's are resolved as i remember . Hope this helps. its been driving me nuts for ages
I have checked the log and theres a lot of lines saying (dvbapi) demuxer 0 no suitable readers found that can be used for decoding . This is where its sticking i think
Im showing 61 cards connected on each line but still nothing across 6 satellites :(
File is unpacked and with the addition of my server file im showing 2 lines connected but still no clearing . ive copied my server file with relevant lines removed etc . can anyone see an issue why nothings is clearing ?
[reader]
label=xxxx
enable=1
protocol=cccam
device=xxxx
user=xxxx
password=xxxx
cccversion=2.1.4
group=1
inactivitytimeout=30
reconnecttimeout=30
lb_weight=100
cccmaxhops=2
ccckeepalive=1
cccwantemu=1
[reader]
label=xxxxx
enable=1
protocol=cccam
device=xxxxx
user=xxxx
password=xxxx
cccversion=2.1.4
group=1
inactivitytimeout=30
reconnecttimeout=30
lb_weight=100
cccmaxhops=2
ccckeepalive=1
cccwantemu=1
Ok ill give it a try , that explains why the softcam will not start . ill be back :)
Cannot seem to get my oscam to work on my solo4K . been off for a while now , Im suspecting its the config file as the server file is fine ;) Is there an updated version for the vix image . I wouldnt normaly ask but i seem to have run out of serch options . Also is is wise to delete all config files etc in the tuxbox/config file before reinstalling then paste the server file back once reinstalled. thanks in anticipation .
