Cannot seem to get my oscam to work on my solo4K . been off for a while now , Im suspecting its the config file as the server file is fine ;) Is there an updated version for the vix image . I wouldnt normaly ask but i seem to have run out of serch options . Also is is wise to delete all config files etc in the tuxbox/config file before reinstalling then paste the server file back once reinstalled. thanks in anticipation .
Cannot seem to get my oscam to work on my solo4K openvix
-
- Arm OSCam
- O B 1
- Closed
- Thread is marked as Resolved.
-
-
then paste the server file back once reinstalled
Trying to run oscam with only an oscam.server file won`t work. You need dvbapi enabled in oscam.conf to view channels.
Use the attached configs. Or attached oscam (configs included).
-
Ok ill give it a try , that explains why the softcam will not start . ill be back :)
-
File is unpacked and with the addition of my server file im showing 2 lines connected but still no clearing . ive copied my server file with relevant lines removed etc . can anyone see an issue why nothings is clearing ?
[reader]
label=xxxx
enable=1
protocol=cccam
device=xxxx
user=xxxx
password=xxxx
cccversion=2.1.4
group=1
inactivitytimeout=30
reconnecttimeout=30
lb_weight=100
cccmaxhops=2
ccckeepalive=1
cccwantemu=1
[reader]
label=xxxxx
enable=1
protocol=cccam
device=xxxxx
user=xxxx
password=xxxx
cccversion=2.1.4
group=1
inactivitytimeout=30
reconnecttimeout=30
lb_weight=100
cccmaxhops=2
ccckeepalive=1
cccwantemu=1
-
Im showing 61 cards connected on each line but still nothing across 6 satellites :(
-
I have checked the log and theres a lot of lines saying (dvbapi) demuxer 0 no suitable readers found that can be used for decoding . This is where its sticking i think
-
Remove these unecessary values:
Codecccversion=2.1.4 inactivitytimeout=30 reconnecttimeout=30 lb_weight=100 cccmaxhops=2 ccckeepalive=1 cccwantemu=1
(dvbapi) demuxer 0 no suitable readers found that can be used for decoding
This error means the server you are trying doesn`t have that specific channel.
Are there any other errors in the log ?
-
the log and server id are showing that the CAID:SvrID 0000:0000 in both log and clines. There are other logs but nothing that i havent seen before. Normally the CAID's are resolved as i remember . Hope this helps. its been driving me nuts for ages
-
Is the tuner configured properly ? Do you get a signal and freeview channels on all sats ?
-
Yes all fTA channels are ok from 28.2E to 30W both motorised dishes move idependant on FBC lnb's so i can rule out tuners . Everything was working up until 3 weeks back . I am routing through a vpn but always have been , even tried turning vpn off just in case but still nothing . Very frustrating as im running 2 clines and each shows connected with 61 cards apeice. just thinking about trying my VUsolo and see if it works on that . or is it the VIX platform needs reloading .. :(
-
I used file zilla to load softcam, just wondering is via usb may work .. I'll give it a try , just to be sure
-
reloaded and installed ipk file, still same result . where is the log file located within the files, if i can edit the relevant out and print that it may be of help ?
-
where is the log file located within the files
oscam.conf > [global] > add this logfile = /var/log/oscam.log > look in /var/log/
-
only showing an empty log called samba in that directory
-
only showing an empty log called samba in that directory
you`ve restarted oscam or restarted the box after editing/saving oscam.conf ?
-
for some reason the oscam-11400 keeps disconecting and reconecting then the " read user data from oscam.conf " reverts to "no" then asking for the usual username ( httpuser), pass (httpwd) ip-address 127.0.0.1 port screen ..
I have reloaded server file but lines keep changing from green to red and having to restart oscam ... head scratching time :/
-
oscam-11400 keeps disconecting and reconecting
Then download oscam from the openvix feed. Its tried and tested..
-
oscam-11400 keeps disconecting and reconecting
Then download oscam from the openvix feed. Its tried and tested..
will do
-
have downloaded latest from vix but still no luck .. getting square eyed at moment from files so ill give it another go tomorrow.
Master G you a star for giving me the time . Its much appreciated . :thumbup::thumbup::thumbup::thumbup::thumbup:
-
Still havinng no luck . just wondering wether a complete reflash of the openvix and start over may be the answer. The log shows connections and the CAIDs are now populated but still nowt on telly. Anyone any suggestions before I start over ? :/:/
OSCam Support Forum
Configs, discussion, downloads and guides for OSCam Softcam.
Participate now!
Don’t have an account yet? Register yourself now and be a part of our community!