Posts by Panda555

The closest satellite according to your longitude is always searched and please don't confuse author of the topic about mount the dish on 0.8W , 1.7 or 1.9 satellite position. About the quote who you didn't undestand I translated better

Quote

When you look at the motor from behind, the motor arm and the dish must be in the same direction

that is, the motor and the dish must be directed towards the satellite in the same direction.

Forget Amos 17 E. This satellite is for Western Africa and cannot be watched in Europe. For you is Eutelsat 16 E. I will quoted here

what I found on one forum on my language. Copied and translated for better understandig how to adjust motorized dish.

Quote

The simplest way is to enter usals parameters into the receiver. switch to a manual and then turn the whole system manually until you get a signal. then just fine-tune the elevation of the antenna and charge the maximum signal you can - check the end satellites and it should work.

- set the engine to 0,

- mount it on the antenna so that it stands directly behind it when you look from behind, neither to the left nor to the right.

Tighten those antenna screws that hold the motor all the way. You don't touch them after that.

- after that, put everything together on the vertical column 100% vertical, and lightly tighten the screws on the column just so that the plate stands.

- after that, type in the usual coordinates in the receiver and save,

- when you have saved usals coordinates, click on one channel with 16.0E satellite, find a weaker one,

- when you chose that, the motor will rotate a little to one side and when it stops, then the whole system moves together (antenna and motor together) and gets the best signal, that means by moving the whole system around the pole and adjusting the elevation of the dish itself, you get a signal,

Also, when you find the strongest signal, the life of the motor on the pole itself begins to shorten,

- be careful, because just by tightening the screws, the signal also varies, so follow it,

- when it reaches the maximum of 16.0E, then turn the engine to say 3W, 7W and 30W in the west and 54.9E and 70.5E and check the signal there.

So you adjust it in 3 points.

- center

- the far east

- far west

Display More

Your quality of signals are good , but must be better on 16 E. Try to up elevation of your dish and check frequency 11554 V 30000.

This frequency is the strongest on this satellite. Signal must be near 100% , with my dish 85 is about 97 - 99 %.

If you will have better results or signal with dish 80 cm , do it the same thing with new dish , but we will see tomorow.

I know that you will solved your "problem" with new dish.

Thank you. Only few frequencies for each satellite.

Astra 19 E

11538 V 22000

11229 V 22000

11361 H 22000

Eutelsat 16 E

11262 H 30000

11139 V 27500

11554 V 30000

11637 V 30000

Eutelsat 13 E

11766 V 29900

11432 V 29900

10971 H 29700

Your dish isn't yet properly adjusted. Also your signal strength will be different then Jenseneverest who is in UK and you

in southern Italy. I will repeat once more , your central satellit is Eutelsat 16 E and when you find the best signals on some

frequencies ( see my post #39 ) then will be much better for other satellites in your range ( especially 30 W which is also important

for adjust). Why not try ?

After adjustment , what is the current signal strength on 19 , 16 and 13 E now ?

I think that you must first adjust your central satellite on 16 E. Also you must choose one of weak channel or transponder

on these satellit. Go to Pink transponder ( 11139 V 27500 ). My signal with dish Gibertini 85 is 57 - 58%. Your signal must be stronger.

Channel signal strength on some satellites as orient for you.

Astra 19 E

ARD 96%

RTL HD 83%

TV5 MONDE EUROPE HD 89%

Eutelsat 16 E

Arenasport 1 HD 76%

Arenasport 4 HD 98%

HRT 1 HD 86%

Eutelsat 13E

RAI UNO HD 81%

ITALIA1 HD 89%

RSI LA1 HD 89%

POLSAT SPORT NEWS HD 92%

ARTE HD 88%

Eutelsat 9 E

CCTV Dokumentary 96%

AFN 90%

Eutelsat 7 E

Zagros TV 93%

Why this site isn't good , maybe is even better than yours. You can't adjust satellite 16 E as first , because isn't your central satellite

if you underastand me. Depending on your longitude find the nearest satellite and adjust the dish accordingly.

I don't have motorized dish , but I will try to help you. You must adjusted your motorized dish according to the latitude and longitude

of your city or town. According to the longitude of your city , true south is required to adjust the dish. The tilt of the hand ( arm ) of your

satellite motor is the latitude of your city or town. What is your exactly longitude and latitude ? Maybe will help this site.

Satellite Dish Pointer with Google Maps, Location Detection

Original port for oscam is 8888. With this port you access OscamWebif in your browser. The port in cccam line must not be changed ,

because it is workin port for cccam line ( example, kcccam.xyz , 12300 user , pass ). Every line which you find on net must be converted

to oscam and added to oscam.server without any change as port of something else. If your line not works , check in oscamwebif and

is enough only change the user. For send files to your box use Total Commander or Filezilla.

pianos5

What exactly crashed , your dreambox two or IPTVPlayer plugin? You didn't write who image you use and which python.

This host in attach is only for PY2 images. If you use image with PY3, this host it's not for you. Also which repo you use

for installation E2iPlayer ( Mario , Blindspot76 or TS - E2iPlayer ).

pianos5

I forgot to add in post above. Host filmpertutti is changed domain ( filmpertutti.run ).

cannon_29

It was no problem with free space , because the image was in OMB. How you see in my screenshots , I installed exteplayer

and serviceapp. Also read my quote about exteplayer. This exteplayer isn't for E2iPlayer if not install ffmpeg libraries before.

There is problem. I think that is problem still in image . When I had installed Pure2 or Blackhole 4.7 ( for DM800SE ) i didn't

had these problem. For now is still Openpli in flash , but I must see which images are compatible with run in OMB .

Maybe NN2 ( newnigma2 ) , but I still don't shure.

PaPs1

Thanks again. Now it works well and I have mainlist. I also installed Youtube by tapaat plugin .

I also found some providers with caid 09CD , but all works with bad sids and impossible to open SKY IT for now

except some channels which I mentioned , because it works with Tivusat card and caid ( 183E , 183D ).

Thank you. Now I understand better. Does that mean that I can added or copy other radio lists in same folder ( hdfradio_mainlist )

or need to rename it with some other name in folder in etc / enigma2. And what about own playlists , you didn't answer me.

PaPs1

Thank you for replay. I found that module ( Python Imaging Library ) in feeds. I still don't understand how to add and where some

other radio lists ( see post #41 ). I added list in Favorite list ( see screenshot ) , but the Main list is empty ( IP radio list was not found ). How and

where to add. In attach are also radio list and how to add. Also how to add own playlists in HDF - Radio Player plugin. Please can you explain me.

Thanks in advance.

After installation this plugin I got a message " No module named PIL " , Openpli image 11.3. I can't find in feeds.

Please can you attach here. Thank you.

You restarted the box when you were on streamrelay channel. When you on streamrelay the tuner is off. When you switch from

streamrelay channel to regular or fta channel you will see short message "No free tuner" . Next time don't restart the box

when you on streamrelay or you will have again the same problem.

For now is not possible to watch SKY IT icam , because the providers ( free clines ) don't have caid 09CD card with K1 and K3

and you can't use oscam as client. It possible to open only few channels in the list for now ( TV2000 , CNBC HD , TV8 HD , cielo HD ).

This is from other forum.

Quote from Talks

Hi guys,

I tried this KeyAdder posted all is correct and working on the update services found BUT seen that none of them have the new update keys with AFN on 9e so I still have to manually put is the new keys in the softcam , keys files.

I did try each provider of the softcam and AFN did not work, why say they are Updated regular when they are not.

Regards Talks.

Display More

I just install Ncam emu 13.5. No problem with autoupdate AFN ( you must wait about 3 - 5 min. ). Only need to properly configure.