Posts by Linesman

Would be for the best then more useful topics

can be discussed like latest firmware box id etc

Satellite dish

look for a sky de server that is not based on cache one with v15

Oscam11719 works perfect with sky de

Open atv 7.3

There has been isues for a long time Movistar have been sending fake cws especially during big

Sporting events

Have tried from 6.4 to 7.2 wirh out any problems All depends on your server

I used invacom l.n.b with Technomate 2600 motor 1.1 traix satellite dish The traix satellite dish is completely different I found good s.n.r

with invacom With motorised satellite installation there is a correction error of +or-1 You could try

to losen the motor bolts and adjust about 1mm

Up or dowm to see if your s.n.r increases across

All transponders Use a permanent mark to mark

Where the elevation lines up on the motor Incase the satellite dish moves due to weather conditions in the future

This might help

s://satlex.de/en/azel_calc.html

Maybe you add this At the start of your

Dvbapi list

P: 186A

P: 1843

P: 1830

P: 098D

P: 0500:23800,40810:4331 #"SRG SSR - SRF 1 HD"

P: 0500:23800,40810:4332 #"SRG SSR - SRF zwei HD"

P: 0D95

P: 0D98

P: 0648

P: 09FD

P: 09C7

P: 0604

P: 0500

I: 09C4

I: 098C

It will never work unless you have the ability

To extract Aes keys

Add this to oscam.dvbapi



P: 1884:000000:32DE #Canal Sport 1

P: 1884:000000:13EE #Canal Sport 2

P: 1884:000000:12C2 #Canal Sport 3

P: 1884:000000:12C3 #Canal Sport 4

Maybe you try watchdogs solutions

Second solution:

One of the following three solutions should be used, both on the server and on the clients (on each device).

1. In the oscam.config file, in the [global] section, enter:

Code:

disablecrccws_only_for = 09C4:000000;098C:000000;0500:030B00;1884:000000;0B01:000000;1813:000000

2. In the oscam.server file for each [reader] enter:

Code:

disablecrccws_only_for = 09C4:000000;098C:000000;0500:030B00;1884:000000;0B01:000000;1813:000000

3. For people using OScam provided in this Post, add such entries in oscam.server for each [reader]:

Code:

lbit_whitelist_services = 0B01_64bit_cw

bothcws_for = 0B01: 000000


and in the oscam.services file enter:


[0B01_64bit_cw]

caid = 0B01

provid =

srvid = 13ED, 32CD, 32DE, 13EE, 32DC

latest version of oscam emu or trunk

You add this to readers and configuration

disablecrccws_only_for = 098C:000000;09C4:000000;098D:000000;0500:030B00,032830,041950,042800,042820,043800,050F00,051A00,051A10;1811:003311,003315;1815:000000;1819:00006D;1802:000000;1880:000000;1884:000000;1708:000000;0E00:000000;09BE:000000;092B:000000;4AEE:000001;0B00:000000;0B02:000000;0D97:000000;0653:000000;092F:000000;092B:000000;09CD:000000;0963:000000

I.P vanish works on wooshbuild

Add V.P.N easily Just select your V.P.N

Provider blue button to save settings

Add your username and password press 1 on your remote to active VPN

looks like its now available to buy

One hundred and fourteen pound

Download latest firmware. If “noforce” file is present in the h9 folder please make sure to rename it to “force”

1. Use FAT32 formatted USB stick
2. Send the h9 folder and 2 files (“bootargs.bin” and “fastboot.bin”) to the clean USB memory stick and then take it out of your PC properly expelled first
3. Switch off your Zgemma H9 at the back, using the white power button
4. Insert the USB stick into the back USB port of your H9
5. Press and hold the small, black RESET button at the back, then
6. Press the white POWER button, while holding the RESET button
7. Let go of the RESET button once you see the LED flashing (changing colour between white and red)
8. Wait for the box to load after the installation.

The A stands for Airdigtal

When booting up it changes from red to clear Its the same process when flashing the reciever

Many problems in the past with

With zgemma h2 series and h9 series

With power problems with h.h motors

With my h2s I had to change my power

Adaptor to the brick type 12volt 5amp

Output and used a low powered L.n.b

This has been covered In the fourm

Before

This was my tunner configuration

Zgemma H1 + Alsat Dark Motor with no LNB connected.

Tuner configuration Menu.

Configuration Mode = Simple

Mode = Position

Longitude = 001.362 West (yours will be different)

Latitude = 052.710 North (yours will be different)

Extra Motor Options = NO

(Green to Save and Exit – Should now show as Positioner : USALS

Manual Scan Menu.

Tuner = Tuner A : BCM7346 (internal) (DVB-S2)

Type of scan = User defined transponder

System = DVB-S

Satellite = 19.2E Astra

Frequency = 11836

Inversion = Auto

Symbol rate = 27500

Polaration = Horizatal

( Press Scan and hopefully the Motor will kick in and move to 19.2E – even not having a LNB connected this works for me).

I think the problem lies with the Zgemma internal memory settings matching up with whats programmed into the Motor settings

If your l.n.b is a sky q l.n.b

This is a wideband l.n.b. The two ports

are marked v and h One.cable feed for

V side One cable feed for the h side

You will.not be able to use this l.n.b

With any twin tunner e2 Reciever

0E00: 000000

0500: 30b00,032830,041950,042800,042820,050F00

098c: 000000

098d: 000000

09c4: 000000

1708: 000000

1709: 000000

1712: 000000

1811: 003311,023311,003315,003341

1817: 000000,00006A

1818: 000000,00006C,000007

1819: 00006D,000007

1841: 000000

1883: 000000

1884: 000000



List off Caids which need DISABLECRCCWS or CWs checksum test,