Before you begin to create a connection between the PC & STB, the receiver must be turned off. After that, not ON the receiver, connect it to your computer, run the program s16loader, in her press connect and once on a computer screen, a message:
Open Serial Port ..
Sync to serial port
Turn ON the receiver and continue to operate after a connection as you need!
I think that today, in FW 1020 best of all published
I tested two weeks 2 possible for the FW configurations:
1. CCcam - server, newcamd - client.
2. Newcamd - server, newcamd - client.
Faster and more stable than the first configuration works.
Files cfg. standard for CCcam and for Newcamd.
Ccam client no, there is CCcam server, there must write settings with your remote and after press the blue button to enter USB cccam.cfg . Then get out of the settings by pressing the exit , go to Newcamd setup setting , and enter with your remote settings Newcamd.After write settings by pressing the exit , to get out of the menu system, reboot and wait when be a picture on the TV.
I stopped worrying and sold that shit. All I can say about this box full of shit, it went on .......... 27 pages on the untranslatable and no understandable Russian mat.
Display MoreI have the same one:
Bootloader: 1.0.0 2011-8-11
Maincode: S3606H-1.0.0 2012-10-20
Seecode: M3606 SEE 2012-10-20
Openlogo: 1.0.0 2012-3-24
defaultdb: 1.1.0 2012-9-11
userdb: 1.0.0 2012-10-20
hardware 1.0.0.10
Have you tried with AZ MIDO_20120618.abs and S4S_721s3606V3_721.abs FW?
Regards
Yes I installed both FW. Both do not work, as it is written in my previous post.
End of my Post. I tested 2 weeks 2 configurations:
1. CCcam - server, newcamd - client.
2. Newcamd - server, newcamd - client.
Faster and more stable than the first configuration works.
Files cfg. standard for CCcam and for Newcamd.
Who wants, to can try ...
Display MoreI have a S16 with information:
Bootloader: 1.0.0 2011-8-11
Maincode: S3606H-1.0.0 2012-10-20
Seecode: M3606 SEE 2012-10-20
Openlogo: 1.0.0 2012-3-24
defaultdb: 1.1.0 2012-9-11
userdb: 1.0.0 2012-10-20
hardware 1.0.0.10
Is my S16 using FW of this topic?
I tried. FW AZfox S4S and AZ ... Installed normally.
FW set to load properly.
When you try to configure the restarts.
This happens every time
when trying to configure anything.
Yesa you are right only one chip from alitech, but the maincode is diferentm but in the receivers that have the maincode 3606d and 3606h NOT WORKING the files 2.8.1 and 16-10 that working with maincode 3606q.
Regards
I think there are several manufacturers of receivers.
Perhaps they in factory flashing FW receivers
write the original version maincod in bootblock loader.
That is why the problems with running other FW.
after maincode version, because the 10-16 and the 2.8.1 firms not work in this receivers with 3606d or 3606h, proved by me
May be but is the only firmware for my Openbox s16 3606d that working fine with all newcamd providers in North American, specifically Mexico
This is a different version maincode and ID chip. There is only one chipset Ali M3606c. Maincode in firmware versions (FW) I've seen four.
There are two FW with Canel list are normally set up and working in North and South America.
Display Morethis may help -
1. Press "Menu"
2. Scroll down to "Network Local Setting"
3. Press "OK" on remote
4. Arrow right to "Newcamd Server Settings"
5. Press "OK" on remote
6. Enter newcamd server parameter
7. Server setting -ON-
8. TCP Port -eg. "13000" this must be forwarded in your router
9. Des Key 01 02 03 04 05 06 07 08 09 10 11 12 13 14 (Can be change to your own)
10. Add USER in Newcamd server User manager with green button on remote
11. Add username PASSWORD "Allow emm YES"
12. Press yellow to save the configuration .
Now box is setup for server with 1 client and a reboot is always a good idea .
In the Client box with CCcam its the N: line to use for acces the server eg
N: server_ip_or_dns 13000 USER PASSWORD 01 02 03 04 05 06 07 08 09 10 11 12 13 14
Thank you so much! Valuable advice for owners Dreambox.
But a small problem, we are in another section of the forum.
In this section discusses the receiver without Linux on board, that is, Openbox S16.
In this section not are discussed Dreambox.
Work week - received a preliminary response to my question. Newcamd is server and the client?
Newcamd can not be used as a client without having to connect any server somewhere, if I do, it starts to slow down.
When using Cccamd as a server to the client Newcamd work is often interrupted and so slow.
In STB Openbox S16 no pre emulator Mgcamd!!!
Therefore, to work with the client Newcamd can use emulators (server) Newcamd.
I tried this option and it turned out that it works better than the rest.
This bunch is configured in a standard way with use panel MENU - Network setting - Newcamd server setting
and blue button USB - set from USB flash - file for the emulator Newcamd - newcamd.cfg. Remember, clicking Exit, exit the menu, restart STB Openbox S16, after a short delay on the screen to appear picture.
What are the main differences between the ***box F3 and the Openbox F16 and will the WiFi USB dongles made for the F3 work OK on the S16 ?
I think the S16 is maybe a newer receiver and maybe not as well supported from a software and firmware point of view, one thing does it have a rear USB port unlike the F3 and are they a similar size ?
Many thanks.
J.
I work with Openbox S16 for two months. Potentially a good machine, its hardware is well designed but poorly done.
Perhaps it can work well, but so far no one has actually seen. The software is very crude and does not know when it will be better. While the S16 is work very bad, especially for HD channels. When switching slows down, the picture opens with a delay of more than 5-10 seconds. F3-STB there is simple, for him is today Canal list, FW for Europe, Asia, N.America, South America.
I'd take the F3.
Newcamd-how to configure the server or the client?
I set Newcamd and it works. But slow and very slow.
There was a question - who is Newcamd:
- The server and the client,
- Server
- The client.?
We all think Newcamd-server!
Who is then the client?
If Newcamd client, who is server - Newcamd, Mgcamd, Cccamd ...?
If developers know the answer to this question, let him answer,
and then we just calm down!
I set Newcamd and it works. But slow and very slow. There was a question - who is Newcamd:
- The server and the client,
- Server
- The client.?
We all think Newcamd-server!
Who is then the client?
If Newcamd client, who is server - Newcamd, Mgcamd, Cccamd ...?
If developers know the answer to this question, let him answer,
and then we just calm down!
I finished the pre-test for FW 1020 from 20.10.2012 and I want to share the initial results. When testing was used TP list of FW 915 from 26.09.2012. Channel list manually create one of Europe's satellite Eutelsat W4 36e.
Receiver works, sometimes slow, when switching SD channels inhibits , when switching HD channels inhibits hard. Quality pictures SD channels high, HD channels is very high. When developers add in FW standard methods to optimize the speed of work receiver, you can probably use it all.
I finished the pre-test and I want to share the initial results. When testing was used TP list of FW 915 from 26.09.2012. Channel list manually create one of Europe's satellite Eutelsat W4 36e.
Receiver works, sometimes slow, when switching SD channels inhibits , when switching HD channels inhibits hard. Quality pictures SD channels high, HD channels is very high. When developers add in FW standard methods to optimize the speed of work receiver, you can probably use it all.
Newcamd was tested for Europe and works ???
I agree with everything you said!
I want to add my thoughts. Please note - I am a professional and this is my thinking, who do not want to read, can not read.
I apologize in advance for my English.
1.Openbox S16 as hardware - a normal machine, there are a few like him receivers on AliM3606 (Tiger T6, Globo 406, Ferguson,Ariva 102 etc.)
And they all work fine.
2.FW that it does not put anything to do with OS Linux. Most likely it is a simple Java code mimics FW listed receivers in item 1 .
3.All attempt to change anything by adjusting or modifying UDFs, DDFs, TP_prog's, Canel list and over will not give you nothing
but headaches and loss of time.
4.Changing situation can only changing the developer, or by recompiling for Openbox s16 , existing working FW created for listed receivers in item 1.
SUMMARY: It is necessary to punish the producers. Need to force them to solve their problems or give away our money.
Display MoreHi - I purchased an s16 openbox and I have a fixed dish. I have set up the box and can view FTA.
My problem is the subscription channels. I have a card that I know works fine, however I get channel scrambled on my S16?
The card shows up in the conditional access menu with 3 separate lines of code(hex) - sorry I'm new to satellites. So I think it can read the card ok.
The supplier of the card showed me it working. he said to leave the channel on and it will eventually de-scramble the picture once it upgrades itself?
It has been sitting on the same channel for about 1-2 hours? Still scrambled. I've read a lot of bad stuff about the S16 Box, have I wasted my money?
I've reset to factory and redone the setup and channel scanning but still no good.
Does it make any difference if the card is in or out of the slot when setting it up? I tried both.
I see 7 BISS Keys but have no idea what they do? should I delete them?
Any help greatly appreciated.
I wrote earlier, S16 with card does not work!
For it to work you need to include emulator Mcas.
But the support of the S16 emulator is missing.
Therefore, nothing can be done except through the channels,
that you get when you make manual adjustments.
Who produces Openbox s16 ?
SHENZHEN VOVOT ELECTRONIC CO., LTD
Contact with main seller:
Company Name: Shenzhen Weibao Technology Co., Ltd.
Street Address: D201, Yangguang Garden, Baoyuan RD, Xixiang Street
City: Shenzhen
Province/State: Guangdong
Country/Region: China (Mainland)
Zip: 518100
Telephone: 0086-0755-23158880
Mobile Phone: 0086 13760405313
Website: Shenzhen VOVOT Technology Co., Ltd. - Small Orders Online Store, Hot Selling AZMAX,openbox-s2,Internet set-top box and more on Aliexpress.com
Contact with main manufactures:
SHENZHEN VOVOT ELECTRONIC CO., LTD, founded in March 2006, with the high technology R&D foundation lead to professional manufacturer of DVB.
Main product of VOVOT is DVB-S2/S, DVB-T2/T, DVB-C, IPTV including: IPTV-IP9000, DOV-8 for Japan, Korea, Taiwan. DM500S, DM500C, DM500HD, DM800HD, DM800HDSe, OPENBOX S16/S9/S10/S11, Satellite Finder, LNB, GPRS Server, Antenna.
Website: http://www.szvovot.com/en/
Information in the WEB:
The following pages contain combined information gathered by searching several sources.
Navigate between the pages by clicking on the tabs above.
Source Date Information
rbls.org Oct 26, 2012 4:04:37 PM Blacklistings
Alexa Oct 26, 2012 4:04:37 PM Description, ranking and other stats
WOT Oct 26, 2012 4:04:37 PM Reputation
Oct 26, 2012 4:04:36 PM Visible DNS Information
Total score 0/50 normalized to 1 out of 5 based on 5 tests Check Result
NS on different IP networks NO
NS delegation consistent with zone NO
Listed in DMOZ NO
Listed in Alexa top 100000 NO
Good WOT rating NO
Indexed in Google -
