Hi oktus! Please, please make such bootlogo but only for OpenPli, ATV and OpenBH without the box inscriptions.
thx
Hi oktus! Please, please make such bootlogo but only for OpenPli, ATV and OpenBH without the box inscriptions.
thx
Press Ctrl+C to stop autoboot
and get boot info
=~=~=~=~=~=~=~=~=~=~=~= PuTTY log 2024.01.08 14:04:07 =~=~=~=~=~=~=~=~=~=~=~=
Bootrom start
Boot Media: eMMC
Decrypt auxiliary code ...OK
lsadc voltage min: 000002FE, max: 00000301, aver: 000002FF, index: 00000001
Enter boot auxiliary code
Auxiliary code - v1.00
DDR code - V1.1.2 20160205
Build: Nov 29 2017 - 19:57:41
Reg Version: v1.6.0\
Reg Time: 2019/05/23 16:52:25
Reg Name: hi3798mv2dmb_hi3798mv200_DDR4-2133_2GB_16bitx2_2layers.reg
DDRS
Boot auxiliary code success
Bootrom success
System startup
Relocate Boot
Jump to C code
Compressed-boot v1.0.0
Uncompress........................Ok
System startup
Relocate Boot
Jump to C code
Fastboot 3.3.0 (h10@builder) (May 25 2019 - 13:59:27)
Fastboot: Version 3.3.0
Build Date: May 25 2019, 14:02:06
CPU: Hi3798Mv200
Boot Media: eMMC
DDR Size: 2GB
Found flash memory controller hifmc100.
no found nand device.
MMC/SD controller initialization.
scan edges:3 p2f:5 f2p:8
mix set temp-phase 2
scan elemnts: startp:131 endp:110
Tuning SampleClock. mix set phase:[02/07] ele:[12/18]
MMC/SD Card:
MID: 0x15
Read Block: 512 Bytes
Write Block: 512 Bytes
Chip Size: 14910M Bytes (High Capacity)
Name: "AJTD4R"
Chip Type: MMC
Version: 5.1
Speed: 100000000Hz
Mode: HS400
Voltage: 1.8V
Bus Width: 8bit
Boot Addr: 0 Bytes
*******************************
serial: xxxxxxxxxxxxxxxx
mac: xxxxxxxxxxxxxxx
*******************************
Net: eth0 phymdio(31) invalid, use default:0
upWarning: failed to set MAC address
, downWarning: failed to set MAC address
, gmac0Warning: failed to set MAC address
Boot Env on eMMC
Env Offset: 0x00100000
Env Size: 0x00010000
Env Range: 0x00010000
SDK Version: ZGEMMA-H10
mac:00:17:9A:26:31:C8
Reserve Memory
Start Addr: 0x7A8FE000
Bound Addr: 0x8D81000
Free Addr: 0x791F7000
Alloc Block: Addr Size
0x7A4FD000 0x400000
0x7A1FC000 0x300000
0x7A1F9000 0x2000
0x7A178000 0x80000
0x79B88000 0x5EF000
0x7939E000 0x7E9000
0x7939A000 0x3000
0x79204000 0x195000
0x791FA000 0x9000
0x791F7000 0x2000
reading STARTUP_ONCE
0 bytes read
Total of 1 byte were the same
Total of 1 byte were the same
reading STARTUP
225 bytes read
byte at 0x01000000 (0x62) != byte at 0x04000000 (0x00)
Total of 0 bytes were the same
Press Ctrl+C to stop autoboot
fastboot# <INTERRUPT>
Display More
unfortunately, that combination doesn't work.
Press Ctrl+C to stop autoboot
install new recovery_emmc from usb also without success.
Hey, everybody!
My zgemma h10 combo has stopped booting, no access to the recovery menu.
I took the boot log from pl2303 uart.
Oh, yeah.
this is from the operator's newsletter
QuoteDear subscribers!
On January 7, from 10 a.m. to 1 p.m. Tashkent time, we are conducting traditional preventive maintenance. Upon their completion, broadcasting of your favorite TV channels will be restored in full.
We ask you not to reboot your receivers and not to scan TV channels.
We make "ALEM TV" even better and thank you for your
unfortunately only official viewing through the provider's card.
It worked fine yesterday.Today i m out so i can not check it.
or did I miss something?
If I understand you correctly, we are talking about Alem TV provider?
Hi!
Please can we have Zgemma H9 Combo and Twin in this style?https://www.linuxsat-support.com/cms/attachment/243081-4k-dreamobx-04112023-1-jpg/
Tnx...
look under in the appendix
Thank you, my friend! You are the best of the best
Hi all.
Please can you make bootlogo in 1920*1080 resolution from these images?
Tnx