Posts by voyager1972

not again,,,,,,,,,,,,,,they would be better going for a late release ,,,,,then bring it out early...............if only those little Koreans were not so busy makin nukes.

CWS_KEEPALIVE = 300
CWS_INCOMING_PORT = 21000
CWS = 127.0.0.1 10000 local local 01 02 03 04 05 06 07 08 09 10 11 12 13 14 lan newcs
CWS = 127.0.0.1 10001 local local 01 02 03 04 05 06 07 08 09 10 11 12 13 14 lan newcs

CWS = yourdyndns.org 12000 username password 01 02 03 04 05 06 07 08 09 10 11 12 13 14

**********above line is fictional and does not connect to anything**************change with your line ,and place in newcamd.list.....restart cam

eaglebox hd ,,,,,,,mmmmmmm......a complete waste of money in my opinion...support was crap....channel lists were a disaster,,,,,so much was promised for this receiver but it never materialised.......stay clear of this one.......

supply,s being supposedly shipped from 8 th july onwards..............images should not be far behind that............a great range of receivers ,,,,,,,,but over priced as usuall..................

the release of a channel editor would be great for this box,,,,,i am very tempted to purchase ,,,,,,,,,,,,but holding back, as the duo 2 is rumoured out this month,,,,would like both but funding could be a problem,,,,,,,,,,

any word on a channel editor for this box????,,,,,,lack of a channel editor has been the demise of many a box......

Well worth doing''plenty of channels open with keys if you're into the footy'''
Technomate 2600 motor with a 1m dish'''vu+ solo2 is an excellant choice for a receiver'''''''black ultra inverto lnb''''''

u can add channels to your bouquets with the remote,,,,,,,you dont need network access for this,,,,,,,you can transferr channel lists to and from your box using dreamset,,,,,there is others but i use dreamset,,,,,u need network access for this so you can connect to your dreambox,,,,,,

so much for your introduction,,,,,,,,

nabilosat addons hasn,t been working on my box for a while now,,,,,,,,

Step 1. You will need to know your latitude and longitude before you start. A great place to fine this is dishpointer.com,,,,,, simply enter your post code, and the coordinates
and displayed below the map. For example if we enter NG12 3PB our coordinates will be:
Lat: 52:54:22N
Lon: 1:02:11W

You need to round up or down the coordinates to the nearest whole number. For example:
Lat 52.5N
Lon 1.0W

Step 2. Install the DisEqc motor and dish as instructed in the manual that came with your motor.
Make sure your mounting pole is perfectly vertical. Once you have done this and connected the motor to your satellite receiver, you need to enter the USALS menu. This will be explained in the receivers manual. Simply enter the the coordinates into the menu. Then select the THOR satellite at 1°West." you dont have to use thor @ 1west,,,,,as 28.2 east will do the same " The motor should move from it's default 0° to 1°West. Select a reliable channel such as BBC World.

Step 3. We presume that you are using a standard in-line meter in between your LNB and the DisEqc motor. Using the meter carefully align the dish to the Thor satellite. You should start to receive BBC World. Fine tune the dish to peak the signal as high as possible. Return to the receiver and select another satellite such as Hellasat at 39°East. Check the Alignment everything should be spot on. If not return to Thor and check the alignment again.

If you followed the instructions properly, you should be able to view a large number of satellites across the arc. Happy Viewing!

ive entered the security code,,,,,still nothing,,,,,,when i click download it tells me at the top of the page that the security code isnt correct,,,,,,tried a lot of times,,,same response,,,,,even tried on another laptop at a differant location,,,,same problem......im baffeled by this

i prefer the openpli image for the dm500,,,,,has a good addons server,,,,as for plugins for the dm500,,,,there is not a lot,,,,,,,,you would be better with an enigma2 receiver for a good selection of plugins........

thanks master G,,,,,,,,,,,

tried again,,,,,,with the above link on 28.2 e ,,,,,,,,,still getting "The security code doesn't seem to be correct. Try again",,,,,,,,,,,,,,,,,,,,,,,im stumped??

ill try later from a differant laptop,,,,,thanks

trying to download latest .xml files,,,,,keep getting this,,,,,,, "The security code doesn't seem to be correct. Try again" ??

im loggeg in ,,,and entering the correct security code,,,,anyone else have this problem.

has anyone purchased this box.......
whats, it like in terme of useability,,,,quality,,,,,channel lists,,,motor control,,,,,ect,ect

n lines can be shared easily within cccam,,,,he will probably use your n line to fake himself a local card,,,,,,"stay clear"

hello cookie,,,,,,im in the limavady area,,,,,,,,,,,,,,,been at this a few years now,,,,,,,,,if theres anything i can help with,,,,,,,just post a question
,,,,,using 1m dish ,,,dm800,dm500,,vu+solo2.......technomate 2600 motor

how do you know if you have a reshare??
in my cccam info which i have my "n line " it says 2 shares available,,,,,,,,what does this mean??