Opensat doesnt look very professional you can get different prices depending what way you try to subscribe , the iptv revolution has started and here start the new wave of payservers
Posts by stevejo
-
-
If you have used the setup and changed nothing just start leaving your box on 5ky1 at night they will be correct , a few people have missed the update and still reported it updating at the last minute you are about 6 weeks out of date when did you do the upgrade , if it was in the last week or so your issue was before that , other than that post your configs to be checked
-
Hi AfyB, I guess it have been paired with original receiver because I had to put it on the original receiver last week to update entitlements as it did not update automatically. I have removed the ecewhitelist but still same issue. Is there any solution to remove the pairing?
Read the rules buddy and post your introduction since sept 2012 you stayed quiet now your stuck your posting
:taxman: -
This will all be bandwidth related and not pc spec jsc is off 13e there will be thousands of people wanting it on a stream , a good time for these type companies to sign up as many people at once and do a runner how long do you think jsc will let it happen , best invest your money in a big ass dish or proper iptv sub
-
You can dump this to a usb stick in the tools section of the menu once on the usb stick check that it is correctly saved by opening it with notepad on the pc , note that some openboxes have an issue with either v or h polarization and this can be fixed by placing a 6db forward path attenuation to the back of the box check if its is this fault as a reflash wont fix it
-
You can use an nline in cccam just add it to the cccam.cfg and your cws= you can change to N:
-
What I did was to use just a foot long piece of coax cable and have the motor next to my box set up my positioner as per dishpointer and drove the motor to 28.2e in my house making sure the protractor under th stub looked like it was at 28e then set my angle on the bracket as per the table given with the motor instructions ,and set the dish elevation on the dish as per dishpointer evevation, made sure my bracket was 100% plumb with a spirit level and when mounting the dish to the motor made sure the split line in the casting of the motor stub was in the middle of the dish bracket using the v of the dish bracket to gauge it then nipped the dish to the stub tight mounted the motor and dish to the bracket not too tight and moved the dish left and right to get 28e with the body of the motor in my hands so as not to force thru the gears till i got 28e best i could , ps i used enigma signal meter for android as very accurate and fast response to adjustments made ,once nipped up i drove to 4.8e as its a weak satellite and further finely adjusted the dish left and right and slightly on dish elevation to get the best signal nipped it up and every thing worked after that , it only requires very small adjustments dont be too ham fist with it
Steve
-
There was an issue with it being slow yesterday only to my knowledge
-
Make sure the folder structure is right on the usb stick ,you cant put the rar or zip on the stick and if this is right , try another image source
-
http://linuxsat-support.com/op…-8m-flash-ali-3606-a.html << use this tool and have a copy of the firmware to hand to load for the box from here should be ok also for you >>http://linuxsat-support.com/op…box-f3s-13-07-2013-a.html
-
Go to the website and try change your pin it might force it thru for you either that or purchase a ppv event
-
That will be the best thing to do or you are not going to get it out the loop nothing else will clear it
-
If you run ABM for 5KY UK are you still getting this error i see the 12606 is radio stations
-
Display More
Hi
I have a venton unibox hd 1 reciever and motor connected to it,it works i have picture but the satfinder in setup menu just show its locked no signal rate on snr and ber display.
Can somebody help me out here please?
Chriseng
Please follow the rules and post an introduction Forum Gateway - Powered by DnP Firewall
-
I would wait and get a solo 2 when you have more cash venton boxes are ok i have the hd3 but you will only get egami vix or opentatv images not sure if more support it yet however vix is my image of choice , £100 more and you can get a lot better and faster box , my advice is to wait and buy a VU+
-
If you want to use one or he other just put a hash in front of the one you want to stop #C: dns port use pass or #N:
-
Sorry Bailkonur wasnt aware you could get an omnikey ci module beer10
-
Smargo smart reader is what i would recommend I use one , but it is usb failing that put the 3rd card in another box and use an nline to oscam
-
i agree with you for cccam but what i notice that it freezes quite a few times....is there a way of adjusting one's receiver setting so that it stops freezing.....
Are you talking clears with cccam as a client or server , if for server clearing to avoid issues use oscam , if client cccam you should have no issues unless they are server /connection related
-
Display More
Hi,
Dont mean to hijack the thread but i got same issue....
My all other entitelements are updating fine no issue there....
I subscribed to BT , but no entitlements came through, rang them up have left the card in constantly....in past 24 hours my other entitlements have updated but nothing for BT
Can it take a while? do i just need patience i been pulling my hair out for past 24 hours...
I thinks the most anyone has said its taken has been about 4 hours most update in 30 minutes mine were instant after online sign up , best ask them to check all details are correct with the sign up and its not incorrect information holding the signals from being sent ,leave the box on a paid channel when requesting
Steve
