Posts by balderdash

If you are using crossepg check it hasnt reverted to flash and is still using the usb to store its dat file

Sent from my MOMO12 using Tapatalk HD

Quote from steve67474

Is this wot u call "on demand viewing"

Lololol :D

Quote from mfazlak

i want all necessary file for dm500s for card sharing i have sum trouble wit the box and how it work ...

Good luck with that..........

Quote from HANNAH

I have a dreambox working with Newnigma2 and Oscam. Can anyone help me see that my sly card is updating. I think I should be able to see this on my PC but don't know how to do this. What should I enter on the PC to check this.

Your boxes ip address plus :8888 or whatever our webif port is,
then enter your webif username and password,

The port,username and password are set in your oscam.conf :)

Quote from Wandro

Has anyone else got a problem with the time on a dm800se on mine I have had to install ntpupdate manager otherwise the clock is never the correct time but in standby the time is all over the place gains hours in minutes next time looses hours the only way to do a timer recording is to leave it on all the time.
Were does the time come from for the display program or tuner?

I'm guessing its a front processor version 3 clone box?

You will need to set a cronjob to poll an NTP server every 2 mins to keep the time correct in standby if you want to use timers for recording etc :)

Try changing the "prefer audio stored by service" to no

Quote from choakem

mario722 - Cheers for the thanks (Not sure why though) :P

Does anyone here use the commando image and if so do you have EPG for ***1+1, Atlantic+1, new disney movie channel etc..

If you do ill load the image and see where the source comes from.

In the old days it was radiotimes as well :P

Display More

It gets its epg data direct from the satellite feed mate

Quote from ashr1

Hi,
I have done my 1st line exchange. The guy gave me his NLine for my Cline.

The question is, what do I do with NLine?
I have a Ubuntu server setup, do I enter the Nline in the cccam.cfg file on he server, and create a f:line then give myself a c:line or enter it directly into my receiver?

Thanks very much for your help

Thanks
Ash

Display More

Presumably you already have setup a line between your server and your viewing box,yes?

If so,and providing he gave you a reshare,then put it in your CCcam.cfg on the server,

If no reshare given then you will need to put it in the cfg on your box instead :)

Post your CCcam.cfg but remove any obvious personal details,also are you sure CCcam is actually running?

What card are you trying to read?

Do you share with anybody else,if so is that working OK?

Have you setup a DNS account?

Are you sharing your card or trying to reshare a share you get from elsewhere?

Try to give as much info as possible so we can help :)

Quote from toothfairy

Happy St Patrick's day one and all.

Same to you m8 :beer:

Quote from cazuela

Balderdash... read my message again :

I dont need to read it again caz,
I only pointed out that you were a few days early,regardless of what it says in your little poem,

and I did wish you a Happy Paddys Day :)

Quote from niall_b73

happy st patricks to all ohh and somebody stated above that you were early with your happy st pat's wishes !!
they have obviously never been to ireland because we here in ireland have been in training for this glorious day for 364 days now and so the cycle starts ;)

enjoy,
niall_b73

Hmm thats funny I thought Dublin is the Capital,must check my map again :ire:

Happy Paddys Day m8

you do realise you are a few days early

Quote from tennents

sorry ment too say dreamup

Are you using a serial port or one of those USB convertors?

Also try a different version of dreamup :)

Quote from bellodreambox

hello

yes it is my own cards but it work in localy is i give my dad c/line to difrent IP address won work ?

Then you need to setup a DNS account and forward the correct port on your router

Is it your own card you are sharing?

Have you setup a DNS account and forwarded the correct port in your router?

Quote from rangers19873

Thanks but I am getting the same response

opensc-tool : invalid option -- `1`
Usage: opensc-tool [OPTIONS]
Options:
lists all different commands :-(

That's a lower case L you need to type, not the number 1

sent using my telepathic powers

Make sure to stop enigma2 first,otherwise it will just repopulate the epg.dat from flash memory

Sent from my Ployer Momo 12

Ok managed to fix it :)

I noticed in the softcam.oscam file in etc/init.d that it includes the path to the config files needed for oscam to run,
So I just added the path for the configs for mgcamd in the softcam.MGCamd file and hey presto it works :)