Posts by geeuk

i am in the same sitiation some of my entitlements were due to expire 19th (today) been on for the last 4 days not updated too... the problem is i don't have the original box anymore..

I think I found the problem after you mention csp/multics i remember a share who kept talking about this so I disabled his and line now I am no longer getting any freezes or not founds :) also I checked drop bad cws and only using newcamd protocol.

Hi,

Its Oscam protocol connected using camd35 and newcamd. But the problem is freezes for a couple of minutes than comes back on.. Once it goes off for 1 user it goes off for all.. I have 4 shares who watch nollywood and they all go off once 1 goes off.

Thanks

Yes I am aware it will go off in the end, just wanted someone to check if also they are having issues on this subject. Thanks for your help mate, will just wait and see if anyone add a bit more info.

I have also updated the oscam and enable cw check still some ecms and dropping and some are ok.. I think this is the same case with ss1 hd when big events are on.

Hi,

The card is out of a Thomson box, I haven't tested it in the box as I don't have it here, I am not sure if the channel works in box but all the HD channels work i assume the channels should work. What I am trying to establish is that any ecm pattern which has FFFF is decrypts fine but other than that anything else just says not found.

I am wondering if there is a way to add the channels which have non FFFF and you have to manually add it?

I mean the channel works in oscam but out of 20 ecms 1 would say timeout and freeze because it's a non FFFF ecm.

Thanks

I have had oscam running for over 2 years all have been working without any issues, until for the last 3 weeks where it decrypts some ecms and some it just goes to not found...

My receiver is DSI8215 so I don't have the security software yet all channels work apart from the Nollywood channel where decrypts some ecms and some it fails and says channel not subscribed...
[***********] classD3 ins54: status 90 00 = ok but cw=00 -> channel not subscribed

The emms were updated today just to make sure that they were not expired. I have the box id and using smargo, not using ecm list but also tried with the list.

I gathered a pattern when its D3C9:FFFF it works fine but when it's D3C9:0600 it fails and says channel not subbed, please look below for a small piece out of my log file:

(0963&000000/FFFF/D3C9/5F:30AEDB36C35A442A85E007077FF70F5D): found (68 ms) by ***01 - Nollywood Channel OK
(0963&000000/FFFF/D3C9/5F:5F576C2B140C2F108F7D00057F6CEBA6): found (82 ms) by ***01 - Nollywood Channel OK
0963&000000/0600/D3C9/5E:01AAD2D942D90ED3310631D1126FDAF4): not found (49 ms) by ***01 - Nollywood Channel
(0963&000000/FFFF/D3C9/5F:59287AA85768788F103DFD00ADA1DA22): found (130 ms) by ***01 - Nollywood Channel OK

I am really confused can anyone tell me if they are also experiencing the same thing?

Thanks

hi mate

thanks for your reply.

yes i do have oscam.services

[premium_premiersports]
caid = 0963
provid =
srvid = C7A9

[premium_premiersportsxtra]
caid = 0963
provid =
srvid = C7AB

[premium_boxnation]
caid = 0963
provid =
srvid = C5CB

To be honest i usally find my answers on the forum and dont usually post anything but this has really made me go crazy lol

Hi,

I am trying to block certian sids from cache ie premier sports and box nation but it's not working for some reason...

Usually putting ! infront of the name should work but its not i am still getting cache3 for the channel.

below are my config files

[oscam.user]

[account]
user = usera
pwd = userapass
description =
group = 10
services = !premium_premiersports,!premium_premiersportsxtra,!premium_boxnation
cacheex = 3
cacheex_maxhop = 3
cccmaxhops = -1

[reader]
label = user
protocol = cccam
device = XXXX,1234
user = user
password = user
services = !premium_premiersports,!premium_premiersportsxtra,!premium_boxnation
inactivitytimeout = 30
reconnecttimeout = 2
cacheex = 3
cacheex_maxhop = 10
caid = 0963
group = 1,10
dropbadcws = 1
cccversion = 2.3.0
cccreconnect = 1200
audisabled = 1

Any help would be good.

Guys lets get back to the subject.

We start getting high ecm (enough to cause glitch's (have only 1 client active) ) from 3am till 3pm today now it's all back to normal.

I have tried with other oscam versions, ecmwhitelist on and off, overclock at different mhz's and try different readers (smargo and omnikey).

Still nothing cured the high ecm.

What I am trying to figure out is if ECM times have any connections with signal footprint test's as mentioned earlier?

The problem is not high ecm the problem is glitching and freezing we get at .800ms, If the ecm was like around .400 constantly than that's no problem as its enough to share to few people. But the issue is the ecm kicks up to .700 to around 1.200 and this causes issues.

I have been reading all the forums lets see what happens.

hi darren can you tell what ecms you are getting on *** sports 2 at the moment? also what is your setup?

Quote from ColinG

Hi All,

Had the same problem with high ecm times on 0963 sly uk.

Just update to the latest ecm whitelist.

Cured it for me.

Times under 100ms again.

0963:3B,3E,42,44,45,47,4B,4E,4F,5E,5F,53,54,56,61,62,65,66,67,68,69,6A,6B,6C,6D,6F,70,71,72,73,74,76,77,78,79,7A,7C,7D,7E,80,82,85,88,8B

If cutting and pasting, remove any spaces.

Oscam 7481 stable. Debian 6.03 server.

Display More

hi,

just started getting high ecms on *** sports channels sd. I done what you said re-built 7481 and used the above whitelist made no difference still high ecms.

Quote from Knippy

700? sounds like to me you got a lot of users?

erm what was the thread about? ow getting high ecm on avarage usage from time to time?

Mate ecm was flying to 700ms than back down to .100 I only have like 10 clients..

Now it seems ok fingers crossed

guys my ecms are alo flying up now! 700ms on most channels.

btw did you manage to post on the oscam forum mate? I looked for post's but couldn't find anything.

Hi,

Thank god it was not only me! I have sleepless night trying to fix it, changed the mhz, changed versions etc still high ecms it has calmed a bit now yes nothing below .300ms when it's high.

Lets wait a for an update guys.

Thanks

Thanks Master G that done the trick! Many Thanks :) :linuxsat3:

Thanks master G i will check that thread now and see if it will work.

lfc4ever I have Linux already and it's really stable :) I normally reboot the oscam daily and but sometimes if i don't reboot pc i seem to get timeouts. So i found it's best to reboot the whole pc at 4am but i need to lock the port.

Hi,

I have 2 omnikeys in oscam one is 0 = setanta and other is 1 = ftv card. It's all working fine both cards have there own groups 1 = setanta and 2 = ftv group.

I have a Powered USB Hub connected to rear usb ports of the computer and than the omnikeys are connected.

They fully work and i have no issues, until i reboot the server than the usb ports swap and groups get mixed up ie 1 = setanta (should be 0) and 0 = ftv (should be 1). It's like someone swapped over the cards!

I tried searching on the forums and google but couldn't get an answer.. The reason i want to lock the ports is i want to allow the server to reboot by it self towards the morning.

Is there a solution for this?

Many Thanks,
Gee UK