hi
i used to watch bbc entertaintment with a legal card and a softcam over dm800hd but since the frequency shift i cant see it with most of the existing softcam,
did they also change the encryption CI card on the frequency change so i need to retrive a new card?
Best regards & thanks
hi
thank you for your answers,
a follow up on this:
can i install for instance add ons like TSPANEL & TSMEDIA directly on an original image?
BR
Shambi
hi
can i install TSPANEL on original DM800?
can i use clone images over DM800 original?
BR
shambi
thanks, tried all that, i think i will go on capacitors replacement, will update
yes, tried with all the cables and even the LCD removed!
some how the USB is operative only when it is in flashing period,
otherwise the unit doesnt even reach the stage in the SW executing that tells the fans to rotate/give usb power to the fans
- - - Updated - - -
hi
i measured voltages across the board and capacitors,
i have 3 big fat capacitors 4700uF/10V in a row - C118/146/222
right after the 4 thin 2200uF/6.3V
on the 4700uF i measured only a few millivolts of voltage, could that be my problem?
BR
Shambi
yeah, i did all that, i think there is a certain hw failure i cannot put my hands on, thanks for all the help!
- - - Updated - - -
hi
i tried that but no luck, same results
the flashing do complete properly,
it starts booting shows boot screen and stuck - than recycle,
it is stuck even before the routine that tells the fans to rotate, the fans are stuck
i also had a problem with my usb dok before it ended in this situation
mabye i'm with the USB circuitry HW problem,
is there a way to bypass the usb and see if the DM will wake up?
BR
Shambi
i think it is seated properly
when i remove it box LCD goes to display "error"
maybe the sequence of operation is not correct, maybe i do not do the reboots in place
maybe the order of 82b image and ssl82b is important, i do not know...
1. update SSL82B using NCF tool
2. should i reboot or not?
3. flash via the network an 82b image
- - - Updated - - -
now I'm flashing a 82b image using dreamup - maybe it will do the difference
- - - Updated - - -
adding a link to a vid showing the problem,
https://www.dropbox.com/s/d29p…-20141102-WA0001.mp4?dl=0
- - - Updated - - -
adding a link to a vid showing the problem,
https://www.dropbox.com/s/d29p…-20141102-WA0001.mp4?dl=0
hi
to summerize
1. receiver isnt working
2. i can flash almost every image by network, i sometimes feel like "flash gordon" already...
3. receiver stuck during load showing only booting screen image, stalls for a few minutes than reboots and goes through these cycles endlessly
4. tried to run "noCAerror repair tool in satdreamGR toolbox" but it just gives me "no such file or no file found" popup and disappears, - means i couldnt operate the nocaerror from the satdreamGR toolbox not that i perfromed it on the DM and it failed, i couldnt get the nocaerror from satdreamGR toolbox to operate.
4a. for instance the dreamup clone from the satdreamGR toolbox did operated on my box.
5. performed a nocaerror report with NCF3.0 from yassinov but no help too...
thanks for all the help and patience
hi
i have a dm800 clone sim2.01
it posts the following errors to the com port,during power on loading
----------------------------------------------
find_inode failed for name=secondstage.conf
load: Failed to find inode
- failed to open /boot/secondstage.conf
- failed to open /cf/autorun.bat
----------------------------------------------
later the DM simply stuck in endless boot,
wonder if someone can shed loght on these errors and the HW/SW issues that might cause them.
complete log attached too.
BR
Shambi
help appreciated!
i was just referring to the "Your log looks like a bad-flash as so much failed on boot?"
did i describe the flashing sequence properly?
my dm did arrive originally with ssl82b
will update...
i getting the impression my dm has a certain of hw failure
- - - Updated - - -
i do not know where to download 82b downloader?
- - - Updated - - -
hi
burned 82 image through lan
burned 82 ssl via ncf 3.0 of yassinov
no luck
i do not have ssl82b boot in nfi file, i couldnt find on the net
openinig aseprate thread for the log fil errors...
BR
Shambi
i didn't understand your question,
1. i can flash back ssl82b boot using dreamup
2. reboot or not ?
3. flash an ssl82b image ?
or
1. flash an ssl82b image
2. reboot or not ?
3. flash back the ssl82b
btw - what is the importance of the ssl82b so much?
so to flash ssl82b boot
flash ssl84 image ?
can u explain what r the errors in the log file means?
br
shambi
thanks again for your help,
what is b4?
i can make no ca error on 84b,
if i understand your 2nd suggestion is:
flash ssl82 image[eighty two]
fladh ssl84b boot[eighty four]
than any 84d image ?[eighty four]
not must the no ca error procedure?
br
shambi
- - - Updated - - -
i wonder if from the log file you understand the cpu doesn't recognize the tuner ?
hi
performed no ca error fix ith yassinov NCF V3 with SSL82b --> flashed SL84D image --> no luck
can you understand from the log file what does it imply
"find_inode failed for name=secondstage.conf
load: Failed to find inode
- failed to open /boot/secondstage.conf
- failed to open /cf/autorun.bat"
what is the unit looking for or what is malfunctioning due to the above log error?
BR
Shambi
- - - Updated - - -
does flashing an image using the dreamup has any edge over the lan flashing method to solve problems?
hi
i got the satdreamgr tools
when i try to activate the no ca error
it returns a "no such file"
also why is the nocaerror valid in optiflasher ?
can someone review the log and see if he can point the problem or malfunctioning component ?
br
shambi
hi
an update,
succeeded to connect with DreamUp but i didnt burn with Dreamup cause it takes a lot of time,
i do not know if burning using Dreamup will fix the problem,
used 76D SSL and image with no luck
operated Dreamup bad sectors fix - no improvement,
i'm attaching the simple log file i recorded from the COM1/RS232 terminal when the unit wakes up from power-on and get stuck,
i still can perform various flash image programming using the LAN interface,
BR
Shambi
hi
was happy to read your problem got sorted,
i'm experiancing similar problem,
u wrote your problem got sorted using "DreamtroolboxGR"
would like to ask if you can elaborate on the way u used the tool and solved your problem?
BR
Shambi
ok
tried - no improvement
it seems it gets stuck right after starting to run,
it writes booting it writes the " ".4-dm800.gzux-2.6.18-" and i think get stuck in the middle...
mabye that is the reason it doesnt connect to DreamUp, it simply stops running after the start of boot,
it shows bootlogo --> than halts --> than reboots after a few minuets --> bootlogo -->....
BR
Shambi
to flash the bootloader using the optiflasher "write image" or "write bootloader" checkbox?
Thanks Shambi
ok i did it, the new bootloader drivers i flashed using the "write bootlaoder/update" checkbox
still - no luck
LCD shows:
".4-dm800.gzux-2.6.18-"
something like that,
* mabye i shuold go to the DreamUp option?
BR
Shambi
- - - Updated - - -
hi
why is the repair/no CA found option is not possible in optiflasher GUI?
BR
Shambi
