Posts by manwithwomananddog

After just receiving my new Slybox F3, I am in the process of sorting through all the channels. I have a 4 lnb via diseqc switch setup on this box. 28.2e, 19.2e, 13e and 4.8e. (4.8e being pretty much a waste of time! lol). It's a very slow process going through all the channels etc. No doubt I will not be using the majority of them. Especially as most of them are foreign language. Would be nice if someone else did this to save me a job! However, I have found before that someone else's, say Canal+ channel, might not be the one for me. i.e. signal on that channel not good here, but another Canal+ (matching) channel is! So then I would have to go through sorting that out anyway! I don't think you can really beat doing it all yourself. But it is a nightmare and BORING doing it!! lol.

Quote from rickyblanes

Why is it so hard to get a list for these 2 satellites and what other prog is available for edit without having to pay for setedit? Any help would be appreciated and is it possible to change dreambox enigma2 settings to an openbox file .dbs ??

Okay. I haven't heard back from him yet, so I went ahead and done this...

[reader]
label = remote
description = Newcamd Example
protocol = newcamd
device = my_mates_server.net,22000
key = 0102030405060708091011121314
user = my_username
password = my_password
#caid = 0963
#ident = 0000:000000
group = 1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21
audisabled = 1

I know seem to be getting all those lovely channels, but I also seem to be having massive glitching issues. I don't know weather it's the poor weather (although that has subsided) or whether it's this setup I'm using?

Is using the above okay, or would it cause issues on scrambled channels?

All I can tell you is that when I was running all this on my other Slybox F5 (using cccam) I just installed a basic Cline and everything just came on! When I was replacing my Slybox F5 with this Amiko Alien 2 he told me he was going to put me on mgcamd instead of using cccam. So now when I boot this box up into 'Spark' I actually get the channels. But as I wanted to run on enigma2 (using oscam) I seem to have this issue? So there is something that I've got to do at my end, and I just don't know what it is! lol.

Hey, I'm learning slowly. :D

Quote from brendanj9554

as it seems like its your friends server he would need to set the access in the oscam.user.

if he has different caids on different groups he may have grouped them, ie. slyuk = group 1 slyit = group 2.

[reader]
label = remote
description = Newcamd Example
protocol = newcamd
device = my_mates_server.net,22000
key = 0102030405060708091011121314
user = my_username
password = my_password
caid = 093B
ident = 093B:000000
group = 2
audisabled = 1

he would need to give you group 2. but don't know his setup so don't take this as gospel.

on my server I have slyuk as group 1 and setenta/boxnation etc as group 2.

when adding a user in oscam.user I assign the user to what group they have access to. group 1,2 = both setenta and sly. group 2 = setenta only. you get the idea

Display More

Thanks for that mate.

So say if I was to add more to oscam.server like this....

[reader]
label = remote
description = Newcamd Example
protocol = newcamd
device = my_mates_server.net,22000
key = 0102030405060708091011121314
user = my_username
password = my_password
caid = 0963
ident = 0000:000000
group = 1
audisabled = 1

[reader]
label = remote
description = Newcamd Example
protocol = newcamd
device = my_mates_server.net,22000
key = 0102030405060708091011121314
user = my_username
password = my_password
caid = 093B
ident = 0000:000000
group = 1
audisabled = 1

... then this would also give me the access I would normally get? When you say 'grouped' them, do you mean like this...

[reader]
label = remote
description = Newcamd Example
protocol = newcamd
device = my_mates_server.net,22000
key = 0102030405060708091011121314
user = my_username
password = my_password
caid = 0963,093B
ident = 0000:000000
group = 1
audisabled = 1

Also, is this the only file I would need to edit?

Sorry for all these questions. :D

Quote from brendanj9554

caid = 0963 is sly_uk on 28.2e.

is you want to clear other sat channels you need the correct caids for the sat. (and a share)

for example, sly italia = 093B0000;093B SLY Italia (13E)

if your friend has other caids on his server he has most likely grouped them,

but at the minute you are only clearing 0963

Display More

I have moved from cccam to oscam since changing my S**box to an Amiko Alien 2 box running enigma2. I have entered the settings below so that I can connect to the server and unscramble channels on 28.2e. However, for some reason when I go to pay channels such as the usual footy ones on hotbird, the channels stay scrambled.

This is what my current oscam.server files reads like:

[reader]
label = remote
description = Newcamd Example
protocol = newcamd
device = my_mates_server.net,22000
key = 0102030405060708091011121314
user = my_username
password = my_password
caid = 0963
ident = 0000:000000
group = 1
audisabled = 1

Now being all new to this, as far as I know that caid = 0963 means S**. Does this above mean that it's telling oscam to ONLY unscramble S** channels and not the others? Or should I be looking at other settings in other oscam files?

Forgive my noobness on this. :D

Right. Firstly, cheers for that. I do appreciate the time you are taking to help me out. Nice one.

Okay, I tried what you said at the start, i.e. removing all the cams etc. It didn't work. So I decided to take your advice and re-flash another image. Start from scratch.
I flashed 'SatStation E2 Alien2 Beta Firmware 21-12-2012'.

During installation I only set up the TV and scanned for the one satellite (leaving my other three that are connected to the other tuner) at 28.2e. So I will be able to see if a channel unscrambles. From the menu I installed only Mgcamd. Nothing else. I then copied over my edited versions of mg_cfg and newcamd.list to the 'Softcam Config Directory' as shown here (Sorry about the reflection of me and the dog! lol)...

I then went back to the menu, then plugins, then to Softcam Manager, here...

Selected that. Then the mgcamd appeared. Like so...

Here I highlighted mgcamd_1.35 and pressed the green button to start it up. But nothing happens. Tried restarting enigma2 etc. But nothing. Out of desperation I also tried selecting that 'start' that you can see on the above picture, but that doesn't seem to do anything at all!

So to let you know what I have so far (as pointed to by that screen shown above):

In the var/tuxbox/config folder I have...

mg_cfg
newcamd.list

In the usr/emu folder I have...

start\mgcamd_1.35.emu
mgcamd_1.35

Incidentally, in the var/keys folder I have the following...

cccam.list.mgcamd
ignore.list.mgcamd
mg_cfg.mgcamd
newcamd.list.mgcamd
peer.cfg.mgcamd
priority.list.mgcamd
replace.list.mgcamd

So, I am not doing anything else with this until you or someone else can offer any suggestion on how to get this working from this moment. Like I said, this is now a freshly done re-flash and I have only copied over a couple of files.

Hope this helps?
:-/

Quote from mrgmx

You don't need Oscam then buddy!

I suggest as you seem to have been playing with stuff lol

Either delete / Remove all cams, Oscam, Mgcamd, Cccam and just re-install the Cam you need!

Or better just start again and re-flash to clear out! Start from clean slate!

Install your image, any plugins then your cam! add your line and report back!

Stuttering could be a number of things, friends server, bandwith, bad weather lol

Start from a fresh and then we can try and work out what the actual problem is....Oscam is server related so shouldnt have anything to do with your end!

have you also changed a couple of settings in your mg_cfg file that is also needed for MGcamd

off top of me head you change this

# box type
# 00 autodetect, change only if you think wrong type detected.
# 01 dbox2
# 02 dreambox
# 03 triple-dragon
# 04 relook
# 05 openbox
# 06 dreambox/mips
# 08 stapi/kathrein
# 09 stapi/ipbox
# 11 stapi/openbox
B: { 06 }

and this

# Log option, summ of:
# 00 off
# 01 network udp log
# 02 log to console
# 04 file, appended ! delete it by yourself, before it eat all your hdd
# + IP udp-port log-file-name
L: { 02 } Ip.of.box /tmp/mgcamd.log (this will show any errors in log file then on your box)

Display More

I'm using it as a line, my mate's running the server side of things.

Thanks for getting back to me. :D

Quote from mrgmx

What you using box for just to receive a share (line)

or are you using it as a server also?

If its just to receive the line you only need mgcamd or cccam emu to use line not Oscam?

Since I got enigma2 up and running, I have noticed how much glitching I'm getting from it. Hardly any on Spark, but on Enigma2 it's terrible on some channels.

Now I know that I have got my system running as described before, but on my Spark setup I am running from the mgcamd plugin ONLY. I have disabled all the other emus, including oscam. So how do I run just through mgcamd_1.35 (i.e. like shown in the previous pics). I have noticed that when I try and set up the above to mgcamd_1.35 (even though I have sorted the newcamd.list file out, I get nothing!

I have noted however that when I have mgcamd_1.35 enabled, the information the right shows me 'CaID 0x0000'. Where as when I have oscam enabled it shows 'CaID 0x0963'. I get the feeling that this is the problem, that mgcamd_1.35 won't work without setting this data somewhere? Any ideas?

Thanks.

Okay.

Been busy. lol.

Firstly, Filezilla. Yes. THAT worked a treat. Thanks. So I created the newcamd.list as you instructed and placed it into the appropriate place on the box. Although I have to say that the 'keys' folder was not there. So I had to create that. Anyway. It didn't work. So I took a look at a plugin I found called 'Oscam setup' or something like that. When I looked into the setup of that plugin I noted that it said that the keys folder was in var/keys not usr/keys. So I copied that newcamd.list to that location too! (files everywhere, what the hell!). That didn't work. THEN, I looked at the files that were already in that folder. Which included a file called 'oscam.server'. I downloaded it to my pc and looked into it. Sure enough I found settings for newcamd. So I removed the examples that were already there, and replaced them with my settings. IT WORKED!!

I HAVE DONE IT!! Woohoo!

Because of your excellent guidance in this I have done it. It's all up and running. I am well chuffed.

THANK YOU mrgmx. You are a Star!

Quote from mrgmx

Not sure if it will make any difference but try filezilla...simples!

use ip from box and image user and password and port number and see if that lets you in!

Thats normally how it works lol

Well, I installed another enigma2 image. This time it was Yoda's Backup Image. I installed Filezilla as you suggested, and it connected perfectly! (nice one)

So then I created a text file called 'newcamd.list' and inserted the line as you shown. Obviously replacing the necessaries....

CWS = mymatesserver.ddns.net 22000 myusername mypassword 01 02 03 04 05 06 07 08 09 10 11 12 13 14

I copied the file over to the box to the location you said. Although, I did have to create the 'keys' folder as it wasn't there.

I restarted the box and then crossed my fingers.

Unfortunately it hasn't worked. I went through some of the menus and on one plugin called 'Softcam plugins' I tried pressing restart!? Still nothing. But I did note that the settings in this bit showed that the keys were stored in var/keys and not usr/keys. So I copied the newcamd.list file to there too. Just in case. lol. (files everywhere, what the hell!)
Still hasn't worked.
I get the feeling that this set of Oscam files might have something to do with it. But I may be wrong.
These files are currently in the var/keys folder...

oscam.conf
oscam.dvbapi
oscam.provid
oscam.server
oscam.services
oscam.srvid
oscam.user

Any ideas mate?

Thanks a lot for that mate. Nice one.
I will follow your instructions and see where I end up! lol.

I'll let you know how I get on.

Cheers!

Quote from mrgmx

Not sure on that box mate but with Enigma2 images using MgCamd you will need to convert your line and put in newcamd.list

as follows

CWS = your.ipaddress.blah 12345 User Pass 01 02 03 04 05 06 07 08 09 10 11 12 13 14

save this as newcamd.list in notepad +

ftp this to usr/keys on your box

You may want to look for another image PREFERABLY one from that may help the issue!

But for MgCamd on Engima2 this is how you enter the line!

Display More

Now before everyone thinks, "are you for real?". I am a total noob. Having only been messing with this cardsharing scene for about a month or so.
So please be gentle. :D

I have an Amiko Alien 2 box and I'm just getting to grips with it. Now as I'm learning my way around Spark, what I really want to do is use Enigma2. The main reason being for the 7 day EPG on it. Now I've installed a HDMU image from another site (sat something) and I have installed an Mgcamd plugin, which I need as my mate is running on this protocol. But I'll be damned if I can figure out how to enter the server settings? It's relatively straight forward when using Spark, but this Enigma2 is another kettle of fish! All I can seem to do on this is to 'start' it. But obviously without the proper line/info it won't work!

Now with another Enigma2 image I tried recently I could access the files etc through my ftp program. But with this image, I get nothing showing up. Even though I HAVE logged into it!

Can someone please help?

Quite frustrating. I have read through so many articles on this, but it sometimes comes across like a foreign language to me! lol.