Posts by Flump
-
-
I had my card out of the official box for a few weeks and it stopped working.
Because my Oscam was not configured properly I was unable to update the entitlements and therefore had to register my card with the official box by entering the Viewing Card Number, Version Number and Serial Number on-line.
Have I now made this card tied to the official box for good or do I have to wait or do something clever to make it work in, say, an Amiko Alien 2?
Otherwise I'm just wasting my time trying to get it to work!?
Cheers -
Thanks but can't see it!
Which plugins are required to run with HDMU in order to set up my home share?
Thanks -
Hi
I'm going to flash my Amiko Alien 2 with the latest HDMU Enigma 2 image.
Can anyone suggest a plugin pack to FTP so that i can try and sort my bloody home share out - or does the HDMU image already have all the goodies included?
I failed to succeed with Spark and Cccam with Oscam so second time lucky!
Flump
-
Right
I've managed to get all of my peer boxes to connect to my Amiko Alien2.
However none of the channels clear...... But they still do on the Amiko.
Also I have to keep turning off cccam, turning off oscam, turning on cccam and then turning on oscam after a reboot.
Getting closer !!!???
FlumpNo problem you just need to enable CCcam protocol for cline or use newcamd to create nline in the Amiko, try this
Oscam.conf
Code:
Code
Display More[global] nice = -1 WaitForCards = 1 logfile = stdout preferlocalcards = 1 saveinithistory = 1 [webif] httpport = 8888 httpuser = admin httppwd = admin httpallowed = 127.0.0.1,192.168.0.0-192.168.255.255 [COLOR=#ff0000][newcamd] key = 0102030405060708091011121314 port = 10000@0963:000000[/COLOR] [COLOR=#008000][cccam] port = 12000 reshare = 1 version = 2.1.3 nodeid = [/COLOR]
oscam.server
Code
Display More[reader] label = lower card enable = 1 protocol = internal device = /dev/sci0 caid = 0963:000000 detect = cd group = 1 emmcache = 1,3,2 blockemm-unknown = 1 blockemm-g = 1 lb_weight = 101
oscam.user
Code[account] user = jaxo pwd = isaknob group = 1 caid = 0963 ident = 0963:000000 keepalive = 1 au = lower card
For Cline in client:
C: ipofAmiko 12000 jaxo isaknob
For nline
N: ipofAmiko 10000 jaxo isaknob 01 02 03 04 05 06 07 08 09 10 11 12 13 14
e.g 192.168.1.10
You can remove the unused protocol from oscam.conf in red or green above and of course change the username & passwords to your own if you wish.:laugh:
-
You are a star!
I will go home and try it in a couple of hours and update the thread.
Thanks again.Flump
-
Thanks....
No - my server box (Amiko Alien 2 with Sly card) is running Oscam and the third party boxes are Technomate and Eaglebox (Cccam or Newcamd capability) with appropriate firmware installed. (I've had them working before on premium share.)I only need to connect the third party boxes to the Amiko on the home network.
Cheers! -
Thanks Guys!
I've copied and pasted the settings below. Should they work ok with the F lines?
Do I have to insert "SERVER LISTEN PORT : 12000" anywhere below?
Sorry for lack of knowledge!
FlumpOscam.conf
Code:
[global]
nice = -1
WaitForCards = 1
logfile = stdout
preferlocalcards = 1
saveinithistory = 1[webif]
httpport = 8888
httpuser = admin
httppwd = admin
httpallowed = 127.0.0.1,192.168.0.0-192.168.255.255
# protocols[newcamd]
key = 0102030405060708091011121314
port = 10000@0963:000000;10001@0963:000000oscam.serverCode:
[reader]
label = lower card
enable = 1
protocol = internal
device = /dev/sci0
caid = 0963:000000
# 0963 is *** UK.
boxid = ********
# Oscam can read a *** card i.d, but you can also put this
# in manually
detect = cd
cardmhz = 357
# this helps the card run more smootly
group = 1
# Oscam has the concept of groups. Only users in group 1 can
# use this reader. I'm only using one group.
emmcache = 1,3,2
ecmcache = 1
blockemm-unknown = 1
blockemm-g = 1
# these ensure smooth decrypting
lb_weight = 101
# for load balancing - can be commented out.oscam.userCode:
[account]
user = Jaxo
description = for local mgcamd or DVBAPI
pwd = CCcamExchange
disabled = 0
uniq = 1
group = 1
au = lower card
caid = 0963:000000 -
Great...thanks....
So what port do you enter in the Cline?
F lines are just:
F: user pass
F: user2 pass2
right?
Cheers again! -
Hi
Could anyone tell me if you want to share a card throughout a home network using a server STB and a number of peers whether you need to open any specific ports in your router? I'm using Oscam with Cccam on an Amiko Alien 2 running Spark with plugins.
F lines in Cccam.cfg.
Basically can you use any port and if so would that port normally need to be opened on the router? Mine's a Thomson router from Plusnet.
Thanks
Flump