Posts by coolestshani
-
-
can some one explain how can I enter dcw keys in softcam.
sample dcw in softcam:
please explain these 1,2,3,4,5.
which is pid, casid etc.2nd question.
how can I take values like vpid from service info, or i have to convert to hex:THanks.
-
try G as 33 and b as 02 or 06... on mg_cfg
tried G as 33 and b as 02 then mgcamd show no ecm info.
tried G as 33 and b as 06 then mgcamd shows ecm info as screenshot above but does not open channel. -
here you go mgcamd screenshot...
even the bisskey is right other receivers are opening the channel.
-
cccam and newcamd lines are working fine.
Only keys are not working.here is mg_cfg
Code
Display More# EMM messages # 00 don't show any EMMs (default) # 01 show only valid EMMs # 02 show valid and bad EMMs with complete data display M: { 02 } # ECM messages # 00 don't show anything about ecm # 01 normal mode, show pids processed, decoded ecm and cw # 02 verbose mode, show valid and bad ECMs with data C: { 01 } # AU # 00 disable, no emm pids processed # 01 enable, emm pids always processed for soft-au and shared cards # 02 auto, emm started only if channel cant be decoded # 03 process emm pids for network cards update only A: { 02 } # key update (sum 01 or 02 with 04) # 01 update only new keys, default setting # 02 update all keys (used for valid PMK checking) # 04 enable TPS au # + tps SID, which pmt pid contains au pid U: { 01 } 0x12c0 # config files folder (softcam, autoroll, ignore/priority) # 00 files in /var/keys # 01 files in /tmp T: { 00 } # network mode, use summ for several clients # 00 no network (default) # 01 newcamd netclient # 02 radegast netclient # 04 camd3 netclient # 08 gbox netclient # 32 cccamd netclient, card list saved as /tmp/cccamd.info # (ECM only, supported server version up to 2.1.1, later not work) G: { 32 } # network retry, use summ for several options # 00 disable # 01 retry every new ecm # 02 try to connect to offline shares every Q: seconds # 04 try to detect and fast reconnect to lost (and not used atm) server # + XX messages number and YY seconds to reconnect # mg will reconnect to server, if no answer to last XX ecm/keepalive or # if no answer for last ecm or keepalive sent for YY seconds # set to 0 to disable N: { 07 } 5 30 # network ecm timeout in seconds K: { 05 } # newcamd dead routes connect retry, sec Q: { 600 } # network shares priority # 00 gbox, newcamd, cccamd, radegast, camd3 (default) # 01 camd3, radegast, cccamd, gbox, newcamd # 02 cccamd, newcamd, camd3, gbox, radegast P: { 00 } # on screen display type # 00 No OSD (default) # 01 neutrino # 02 enigma # 03 relook # + user password for http auth O: { 00 } username password # on screen display Options, summ of: # 01 show emu ecm # 02 show network shares messages # 04 show decoding failed / fta # 08 show emm keys update # + web port to use for osd S: { 03 } 80 # Log option, summ of: # 00 off # 01 network udp log # 02 log to console # 04 file, appended ! delete it by yourself, before it eat all your hdd # + IP udp-port log-file-name L: { 03 } 172.16.1.1 28007 /tmp/mgcamd.log # keep ecm cache, seconds # every cache entry takes 28 bytes, so 24h cache will take *only* 240-400kb of memory, # for openbox/elanvision users with remote shares make sense to set it higher than default value, # to not hammer cards while timeshifting or playing crypted recordings. E: { 15 } # cache option, summ of: # 00 Off (default) # 01 Ecm pids cache, store pids used to decode in /tmp/ca_cache.list at exit, load at startup, same syntax as restore.list # 02 Ecm data cache, remember CW for (E:) time # 04 Emm cache for network cards, do not resend the same emm twice, cache not cleared until restart H: { 07 } # reread files, summ of: # 00 No (default) # 01 reread config file on channel change (including priority and ignore, but not replace/cache) # 02 reread SoftCam.Key on channel change # 04 reread SoftCam.Key if file changed R: { 00 } # debug, summ of # 00 off (default) # 01 debug ecm # 02 debug emm # 04 debug network ecm # 08 debug network emm # 16 debug network login # 32 show mem/cpu stats every 1 min # 64 add timestamp to log messages D: { 00 } # box type # 00 autodetect, change only if you think wrong type detected. # 01 dbox2 # 02 dreambox # 03 triple-dragon # 04 relook # 05 openbox # 06 dreambox/mips # 08 stapi/kathrein # 09 stapi/ipbox # 11 stapi/openbox B: { 00 } # map all 180x nagra caids to 1801 # default is 01 F: { 01 }
-
hello,
I am having problems with mgcamd 1.38 on OpenPli 2.1 which is installed through tspanel.
I am trying to open Edge Sport on 100.5°E with this working biss key. Biss key is working on starsat receiver.
I have edited softcam.key in usr/keys/ with dcc and entered the following:tried on cccam too but not working.
Pid etc listed below:
ECM: CaID: 0x2600 -> CaPID: 0x1FFF ProvID: 000000What am i doing wrong?
Help............... -
will this work on openPli 2.1 dm800HD clone?
-
try this image best for clone.
openpli-2.1-beta-dm800-sim2-ssl84bQuote -
Hi,
I have got a dm800Hd pro clone with m-tuner and I am facing a very weird problem only on c-band lnbs.
I can not tune any vertical transponders on c-band. Horizontal tps are all ok.
Then I checked on my other 2 receivers and all transponders both H/V are working.After 4 days of searching on the only solution found was that i had to subtract 600 from Vertical transponder and then scan. Voila Vertical Transponder signals were working.
I was angry and also confuse about this problem.
I had tried everything, each and every solution I could find. Changing images, tuner settings, diseqc settings etc but nothing worked. The only trick that worked was subtracting 600 from transponder and scan.Tried these images
OpenPLi-2.1-beta-dm800-20130311.by aguda
BlackHole-1-7-0-dm800hd-ramiMAHER
D-M-S-image-dm800-OE1-6-v6-0-ramiMAHER
openpli-2.1-beta-dm800-20130905-sim2-ssl84b [currently working]Does anyone have a solution for this.... Manual scanning each transponders is really a hurdle.
Any help would be appreciated.
Thanks -
IPTV List Updater not working on oe1.6
Image name : DDD-dm800-OE1.6-v6.0 -ramiMAHER #ssl84b
Error: bad magic number....Any help would be appreciated .