Posts by longstack

How do you change from usals to disqu in the motor set up on the VU+ solo

When you use the Diseqc do you just select Satellite as usual. ( say 19e on 1 13 on 2 ) Looks good..

Buy one from someone who does',nt say its locked . T

thanks m8 great help

are there any problems using Virgin Media cable Broadband, for CS.

Another way is to use a VU Solo Backup image. From here. It will have all the setting on it plus CCam installed for you . Try this one
http://linuxsat-support.com/vu…olo-backup-ten-below.html
It works well the latest but it has what you want. To find how to install the new image go to solo Tutorials . Here .http://linuxsat-support.com/vu…ow-usb-flash-vu-solo.html
Hope this helps

http://linuxsat-support.com/tu…oblems-advice-please.html

Try this post Help here

You say you have a VU+ solo. The first thing to do is Download a Complete Settings list. The best one is the Catseye E2 settings list 75e to 45 w. you can download it here. Or better still you can download it from your image. Then you will have all the satellites already on to your box. What Image are you using.

Got a strange problem When I use my VU + which is on a Static 3 dishes and Disq switch it works well great signal . When I switch my Spider 9000 box on which uses a different motor dish the VU+ signal goes off. The Spider is above my VU but about 12 " higher. Any suggestions.

thanks for help,
put the New Blackhole On and after a lot of time got it working

Trying to remove coolTV plugin off Blackhole Hyperspace Img. Cant find it anywhere. Any help please.

Is there a better Image than Blackhole I can't get ex HDD or USB to work. I have tried everything and It still wont work.

Thanks for the help.. I had a good Idea just a couple of things I was stuck On.. Great Help !!!

I want to put a Cline into Solo + using Blackhole.
I have Notepad and Dreambox toolbox. Got a rough Idea but not to sure how to do it..
Have Cams up and Working.

Can anyone help have connect a friends New blade 7000 for them . The Blade works fine but As the Panasonic TV uses Satellite they want the Blade and the TV to connect to satellite. ( but not at the Same Time) Got a problem when using the Blade Sat Aerial loopthrough the TV will not work when the Blade is on standby. The TV will only work when Blade turned on. Then the Panasonic TV can only get H or V channels opposite to the one the Blade is using. Is there a way to correct this. On the Spiderbox there was a power saving which caused this problem. Is it the same on the Blade and if so how do I turn it Off.

I have just updated Image on My Solo. The New Image does not come with Motorised Dish Fine Tuning. (Adjust Poisition.)
Any suggestions for one that does.

Thanks M8 All Done Thanks.

thanks m8 is that file for the solo not the Solo2

Got a Genuine VU+ Solo Want to Update to Open Vix 3.0 Image . Do I need New Bootloader. If I do where do I find It.. Using Image Old DreamboxUK at the moment and Having problems with It..

Spiderbox HD Softcam 20.06.2012

12111 H sr 27500 fec 5/6 Sirius 4 (4.8°E)Arqiva channels
Rai 13 east 10992 V sr 27500 fec 2/3
Mezzo 13 east 12245 H sr 27500 fec 3/4
Tv globo 13 east 11585 V sr 27500 fec 3/4
Sic international 16 east 12736 V sr 3703 fec 7/8
Orf Digital 19 east Packages: ORF Digital - KingOfSat
Ant 1 europe 39 east 11052 V sr 30000 fec 3/4
Bulsat 39 east Only I***** Channels Packages: Bulsatcom - KingOfSat
Austria Sat 19 east Packages: Austriasat - KingOfSat
CANAL+NL i***** only 19 east Packages: Canal Digitaal - KingOfSat
Canalsat 19.2°E Provider : 022610 11739V/11778V/11973V/12663H
CANAL+NL i***** only 19 east Channels updated

Orange = updated
Green = Down
RED = All Ok

CANAL+NL i***** only 19 east Channels updated