Posts by kevinbasra

  • Problem with one client freezing after 5

    hi i have a problem where a particular client is having problems with his box feezing after 5pm. It then seems to sort itself out by 11pm ish but has the same problem again. i have removed his c line given him new one as well as re imaging his openbox s10. any ideas?

  • cccam boxkeys

    is it possible to add more than one box key and if soo how shud the line read in cccam. reason i am asking is i sometimes swap over the cards i have in my smargo.


    BOXKEY: /dev/ttyUSB0 xx xx xx xx
    BOXKEY: /dev/ttyUSB0 yy yy yy yy

  • debian 6 and smargo cccam 2.2.1 only first client is active

    # CCcam team uvadi CCcam v2.2.1


    ######################################################################
    # friends #
    ######################################################################
    #
    F: jas jas


    F: sean sean


    F: bambi bambi


    F: custard custard


    F: basra basra
    #




    ######################################################################
    # Other config settings #
    ######################################################################


    #
    SERVER LISTEN PORT : xxxxxxx


    #
    #ALLOW TELNETINFO: no
    ALLOW WEBINFO: yes


    # Show extended client info when showing client list
    # default is yes
    #
    SHOW EXTENEDED CLIENT INFO : yes


    # The webinfo service can be protected with a username and password.
    # This is switched off by default
    #
    #WEBINFO USERNAME : <username>
    #WEBINFO PASSWORD : <password>


    # The telnetinfo service can be protected with a username and password.
    # This is switched off by default
    #
    #TELNETINFO USERNAME : <username>
    #TELNETINFO PASSWORD : <password>


    #TELNETINFO LISTEN PORT : 16000
    WEBINFO LISTEN PORT : 160xx



    #
    SERIAL READER : /dev/ttyUSB0 smartreader+


    # Serial reader smartcard write delay.
    # Setting to finetune smartcard write speed, optimal setting depends on speed of system, and
    # speed of card. Default value is calculated, but can overrule by setting.
    # Use number of microseconds delay between bytes, 0 = no delay, -1 = calculated default
    # Note: huge difference between values 0 and 1, because of schedular overhead
    #
    # SMARTCARD WRITE DELAY : <device> <delay>
    #
    # example, 10ms write delay on smartcard in reader attached to /dev/ttyUSB0
    #
    #SMARTCARD WRITE DELAY: /dev/ttyUSB0 10000
    #
    # NOTE on sc8in1; because 8 smartcards are used on the same devicename, use
    # devicename_0 .. devicename_7 for settings which require devicename to make
    # settings per smartcard. example /dev/ttyS0_0, /dev/ttyS0_1 ..
    # example, 8ms write delay between bytes to smartcard on last sc8in1 channel, attached to /dev/tts/0
    #
    #SMARTCARD WRITE DELAY: /dev/tts/0_7 8000


    # Smartcard clock speed override
    # Setting override specified speed for smartcard.
    # Don't add setting unless you're sure what you're doing.
    # In 99% of the cases the reader selects the optimal speed.
    # Adding this setting either slows your card down, or might destroy it.
    #
    # SMARTCARD CLOCK FREQUENCY : <device> <freq>
    #
    # example
    #
    #SMARTCARD CLOCK FREQUENCY: /dev/ttyUSB0 5500000


    # if timing should be shown in OSD and debug output
    # default is no (turned off)
    #
    #SHOW TIMING : yes


    # enables mini OSD which shows server(type), cardreader, keys or fta only
    # default is no (turned off)
    #
    #MINI OSD : yes


    # turns debugging on and off
    # default is no (turned off)
    #
    #DEBUG : yes




    #
    BOXKEY: /dev/ttyUSB0 xx xx xx xx

  • Problem with Debian 6 and Smargo

    Debian 6 CCcam.cfg doesn’t work
    F: xx xxx
    F: xxn xxx




    SERVER LISTEN PORT : XXXX


    SERIAL READER : /dev/ttyUSB0 smartreader+


    BOXKEY: /dev/ttyUSB0 xx xx xx xx


    Dreambox config works


    BOXKEY: /dev/sci0 xx xx xx xx
    SERVER LISTEN PORT : xxxxxx
    F: xxxx xxxx




    config


    ew Config present, Nothing to process
    No New Config present, Nothing to process
    New Config Present
    Backup directory does not exist.
    making new directory
    No Original Config File Present!?!?
    Moving New config file to /var/etc
    No New Config present, Nothing to process
    No New Config present, Nothing to process
    No New Config present, Nothing to process
    No New Config present, Nothing to process
    No New Config present, Nothing to process
    No New Config present, Nothing to process
    No New Config present, Nothing to process
    No New Config present, Nothing to process
    No New Config present, Nothing to process
    No New Config present, Nothing to process
    No New Config present, Nothing to process
    No New Config present, Nothing to process
    No New Config present, Nothing to process
    No New Config present, Nothing to process
    No New Config present, Nothing to process
    No New Config present, Nothing to process
    No New Config present, Nothing to process
    No New Config present, Nothing to process
    No New Config present, Nothing to process
    No New Config present, Nothing to process
    No New Config present, Nothing to process
    No New Config present, Nothing to process

  • Problem with Debian 6 and Smargo

    hi thanks u so much for responding yes exactly like that if i go onto my openbox and view cccam file it tells me that its online and cccamphpinfo tells me that client is connected.


    many thanks for your help in advance

  • Problem with Debian 6 and Smargo

    Hi i was wondering if anybody could help me with a problem i have with my setup?


    i have a debian 6 server built with cccam 2.2.1 and a smargo reader i have entered my sly box key and cccaminfo shows me i have full entitelments off my card and seems to be reading it ok. my openbox shows that i am connected to my home server however everything is still scrambled???


    if i put my card in a dreambox 500 i have it decodes fine?


    appreciate any assistance with this thanks in advance