Yes, this is I'm affraid from
Posts by saalty
-
-
Do you have an idea how to make this services file in the most simple way?
-
Hello all!
I have Ab PULSe 4k (DVB-S2X and DVB-T/C tuners) with OpenATV 7.4 and OSCam 2.24.10-11845-802. I also have my mediacard for cable tv with CI+ module. With CI+ Helper I can watch cable tv cannels using my CI+ module, but in Oscam log I see that also Oscam wants to find the matching reader. I looked arounf the internet, and I found that ignoring corresponding CAID's in dvpapi file is not the solution. Is there any solution to setup Oscam (or OpenaTV itself) to ignore triing to open channels opened by CI+ module?
-
Hello!
I have Ab PULSe 4k with OpenATV 7.5. My Menu button on the RC doesn't work. The situation is same with OpenATV 7.4. With my Vu+ Zero 4k OpenATV 7.4 (devel) it worked. But in the past I had this issue with Vu+ too, can't remember with which image, or how I solved it. Is there any solution for this issue? Sometimes I need the menu during when I'm watching iptv.
It's OT but your remote just need to be cleaned inside.
To fix it gently open it with the use of plastic levers if you have any, there are clips all around the perimeter so be carefull, clean the remote's board with some alcohol, better if isopropyl alcohol but also normal denatured alcohol is fine, let it dry and close it again, the buttons should all be functional again as new.
/OTNo! My remote work perfectly. Only if I use Multistalker-Pro then Menu button has no effect (also other buttons). If I use cable or sat tuner there is no problem.
-
Hello!
I have Ab PULSe 4k with OpenATV 7.5. My Menu button on the RC doesn't work. The situation is same with OpenATV 7.4. With my Vu+ Zero 4k OpenATV 7.4 (devel) it worked. But in the past I had this issue with Vu+ too, can't remember with which image, or how I solved it. Is there any solution for this issue? Sometimes I need the menu during when I'm watching iptv.
-
Today morning after more than eight hours powered off ie. in standby I turned on and picture comes immediatelly. Weird.
I rebooted yesterday, but I did it earlier, so I don't know is it changed anything. What I also tied is that ti check is it a clock on display in deep standby, I was put in deep stans by and woke it up from there. Also don't know it can be change anything. Soit's weird anyway. If it happens again I will try another HDMI port, honestly I used this port for VU+ Zero 4K for long time, also except this issue my PULSe also works fine on this port. Maybe I'll try OpenATV 7.5 if issue happens again
-
It not gives the signal to the tv through HDMI during this around one minute of time, as my tv shows no signal on hdmi port, like it is switched off, not black picture. Maybe I did not write it w beforeell. But the touch button changes from red to blue on the receiver. And after a minute there is a tv programme appears on the tv without any further control
-
Hi all!
I have receiver mentioned in title with OpenATV 7.4 image. I have this receiver since Tuesday this week. My problem is that if my receiver is longer time in stand by mode, then after I turn on I need to wait around one minute until picture apperars even if the touch button on the front panel is blue. If during this time I turn off and on again, the picture appears immediatelly, so I dont think that it is a hardware issue. For shorter time in stand by this issue not happen ie. picture appears immeditally after turning on. The receiver is in standby and not deep standby as I see the clock on front display. Is there any idea what can cause this issue and can I solve somehow?
-
If you delete crl-verify (including <crl-verify> and </crl-verify> lines) part in ovpn file of PIA it will work with VPN Manager on 7.4.
-
PIA'nın ovpn in the file crl-verify (<crl-verify> ve </crl-verify> dahil) If you delete the part VPN Manager It will work with .
I did as you said, but MONEY did not work for me.
<crl-verify> ve </crl-verify> Did you delete the lines as well?
Yes, I deleted all those parts.
And you are sure that VPN Manager is using that modified ovpn file?
I'm using it right now, so for me this way is worjing
-
If you delete crl-verify (including <crl-verify> and </crl-verify>) part in ovpn file of PIA it will work with VPN Manager.
I did as you said, but PIA did not work for me.
Did you delete both <crl-verify> and </crl-verify> lines as well?
-
If you delete crl-verify (including <crl-verify> and </crl-verify>) part in ovpn file of PIA it will work with VPN Manager.
-
Is there any way to see epg in the plugin, not jusr now-next? Will be in the future?
-
Hi all!
May I ask that is it possible to use this plugin with PIA account on OpenATV 7.4.1-devel? Previously I used VPN Manager but for a wile it stopped working. What I trie is to set custom config file in Settings and copied the conf file from OpenVPN direcrory previously made by VPN manager, but I got an error message that wireguard protocol missing, and to try to install it via telnet (opkg install wireguard-tools), however it is installed...
-
Dear all!
I used VPN Manager to use my PIA account earlier on OpenATV, but for a while it is not working (there is some posts about it in related topic).
Is there any way (other plugin or what else) to use my Private Internet Access account on my VU+ Zero 4K box with the latest OpenATV 7.4 or 7.4.1-devel? I like this image because some of the plugins what is use woring fine on this image but problematic on others, therefore I do not wan't actually to replace it because of the VPN...
-
Anybody knows when will be working on OpenATV 7.4 latest version?
-
Reinstalled and it is wrking fine. Maybe installed the other version than ARM previously
-
Already did it
-
Hello all!
Installed the 1.2 version on VU+ Zero 4K (latest OpenATV 7.4) and seems the installatios was successfull but not found in plugins. Also if I go to remove plugins I find it there. Any suggestions?
-
Installed, looks like working well. Thanks for your help
