if you have as you say in first post, the satstation immage installed you will have to convert the cline to oscam format (very easy) then put it in oscam server file, locate it at var/oscam/conf/oscam server if i remember rightly, to convert the cline read up on the site you got the immage from its all there under sticky in qbox hd mini section
Posts by lacierva
-
-
hi all,
any one know of a good website to buy this package with activated sub and decoder for sly deuchland football ? and approx cost ? thanks -
-
Now fixed, just tested, Enjoy!...
thanks master g i have got so used to catseye lost without it, been trying all day to install it, so hopefully now will be ok, thanks to a great site and fantastic mods !!! -
Which image are you using so we can test/fix the download on TSPanel ?
using black hole 1.7.6 -
there seems to be a problem on server ts panel for downloading latest catseye motor settings only on catseye, so downloaded vu toolbox to use dreamset , downloaded latest file for catseye and unzipped it to desktop, followed set up tuts for dreamset and it communicates with vu ok and can transfer the list i am using now (flipflop) into dreamset for editing, the problem i get is trying to upload my new catseye to dreamset get can not load file, is there a way to ftp instead
-
got there in the end, no diference of folders for clines or flines they go in same cccam configuration, now waiting for card to arrive , thanks all for helping me !
If you receive a C line add it to the same CCcam.cfg where you have been creating F lines..
-
its not that i am usure how to make the cline and fline, my question is do the two lines sit in the same cccam. cfg folder, assuming i am also going to get a share from somewhere ?
with a bit of luck
-
its not that i am usure how to make the cline and fline, my question is do the two lines sit in the same cccam. cfg folder, assuming i am also going to get a share from somewhere ?
Display MoreDon`t use this default port, change server listen port: in CCcam.cfg to something less obvious to a hacker like 52453.
This guide should help explain alot >> Getting Started - Flines & Clines For Beginners.
This tool will create C & F lines for you if you are unsure how to >> CCcam Lines Manager.
-
ok i have set up a no ip account and port forwarded 12000 and checked canyouseeme.org and its working ok my doubt now is fline, does this go in the same config box as cline do the two lines work from that folder or are they different folders ? thanks for your help, i think i might just be leaving the tunnel soon !!!
If you want peers to be able to connect to you from outside your home network then you will need to have dydns buddy,when your ip addy changes the dydns updates this information to your peers so that they can still connect.
-
i assume because i am just using the vu as server there is no need for dydns account , just port forward 1200 ??
You are seeing light at the Tunnel mate! Yes you are!
:thumbsup:
Post back if you have any problems when setting up/following steps!
-
There are a few things you need to do first, portforwarding, change passwords ect. Start by reading these.
Cardsharing Tutorials
i think i can just keep the bh image i am on and download oscam-cccam for card conf from linuxsat in ts panel , then do port forwarding, am i on the right track ? -
so ten, can I just use your back up for black hole ready for sly, then change configs for my card, and then ready to share ? All other connections conf, port set and all internet configs done?
-
There are no back up images with the card I want to use, LoL
-
is there a tut on setting up vu solo as small server ? looked all round forum and no can find a clear pointer in all you have to do,
-
dont think so , but satstation is best image, but its all the same when it comes down to configs
-
this an interesting thread, i am way down southern spain sevilla and on a 1m motorized set up get all ad sports about 45% quality so i think in london you gona need a decent size dish
-
[reader]
enable = 1
label = remote_newcamd
protocol = newcamd
device = your details
account = your password
key = 0102030405060708091011121314
group = 1
emmcache = 1,2,2
blockemm-g = 1try this conf in oscam server, just insert your details, this works 100% for me with qbox hd, also make sure there is nothing else in oscam server file, delite everything before you put this in
-
when its running ok you will get a green flash on the led on front box, if its decoding ok, every few seconds, have you installed channel lists ?
have you installed the oscam simple panel, from there you can start / stop and see whats going on with connection -
have you the oscam server config correct ?,
navigate to var/oscam/conf/oscam server, delete every thing that might be in there and then insert your n line converted as oscam conf, delite all the # you have in front of each line of text, and see if it works
