Marker Id returned from flash:0 does not match
I fix brand new chip samsung K9F2G08U0C is green connected in jtag but cant flash bootloader..its genuine solo2 ..any suggestions?
Solo2 Jtag
- jaaa1976
- Thread is marked as Resolved.
There are 6 replies in this Thread which was already clicked 1,938 times. The last Post () by teak-won-do.
-
-
master G
Moved the thread from forum Vu+ SOLO2 Support to forum VU+ SOLO 2. -
Hi!
Where can i get tools for solo2 jtag?
-
Hi!
Where can i get tools for solo2 jtag?
Check with hardware forum from johnny,
Emo
-
Marker Id returned from flash:0 does not match
I fix brand new chip samsung K9F2G08U0C is green connected in jtag but cant flash bootloader..its genuine solo2 ..any suggestions?did you fix your solo2 ??
-
Marker Id returned from flash:0 does not match
I fix brand new chip samsung K9F2G08U0C is green connected in jtag but cant flash bootloader..its genuine solo2 ..any suggestions?did you fix your solo2 ??
hi..it was more boxes i fix after..what is your problem?
-
Marker Id returned from flash:0 does not match
I fix brand new chip samsung K9F2G08U0C is green connected in jtag but cant flash bootloader..its genuine solo2 ..any suggestions?did you fix your solo2 ??
hi..it was more boxes i fix after..what is your problem?
No problem at the moment, my box is sunray solo2.
-
QuoteAbout the Jtag Solo2 original...Display More
Hardware/software needed..
1. Vu+ Solo2 receiver for the connection to the P701 connector.
2. CY7C68013A development board.
3. Broadband Studio 3 software with the the bcm97346 cpu drivers.
4. CFE bin file.
5. And (of course) a windows computer etc.
First install the,
1. Broadband Studio 3 software.
2. Then connect the development board with the usb cable, turn it on, driver install will follow.
It will do this driver installation twice.
3. Switch off the development board, Connect the Gnd/Sda/Scl wires to the P701 connector.
Mb P701: Scl -> Cyb. Scl
Mb P701: Sda -> Cyb. Sda
Mb P701: Gnd -> Cyb. Gnd
Howto connect step 4.
4A. Start up the Broadband Studio 3 software,
4B. Choose the Bcm97346,
4C. Turn On the receiver,
4D. Switch on the development board.
Or when it not connecting,
4A. Switch on the development board,
4B. Turn On the receiver,
4C. Start up the Broadband Studio 3 software,
4D. Choose the Bcm97346.
And when all is correct, you should see the connection to the Bcm97346 cpu but when not, switch Off the motherboard, and turn it On again.
After this you must see a connection, if not, then you have not a good working motherboard or development board or some other cause.
5. Choose Flash explorer, choose Samsung K9F1G08UOA, press Refresh, Browse to the Cfe file and press Start.
When finished, disconnect the development board and upload a image file on the regular way by Usb.
Download...
The Broadband Studio 3 software with the the bcm97346 cpu drivers and pdf instructions can be downloaded from mega.nz, file is 84.3Mb.
An Cfe bin file can be downloaded from beneath, it's for the original, but can also used with clones because I've tested it on a solo2 clone with a new nand flash chip.
And also included the Usb drivers download, normally it should be already installed after the installation of the Bbs software, but just in case you needed.
Attached Files:
thx to Johnny B.
VU+ SOLO 2 PVR Ready Linux Enigma2 Receiver Full HD 1080p
Download VUPlus Images and Enigma2 Team Support from Black Hole, OpenATV, OpenBH, Open Black Hole, OpenDroid, OpenESi, OpenHDF, OpenLD, OpenPLi, OpenSPA, OpenViX, Open Vision, PKT Hyperion, PurE2, SatDreamGR, VTi.
Participate now!
Don’t have an account yet? Register yourself now and be a part of our community!