Hallo,i have a vu+solo2 and also have two nagra cards for tv vlaanderen and canal digitaal.Is there any possibility that can play to my vu?Thnaks.
tv vlaanderen and canal digitaal problem
- jumaru
- Thread is marked as Resolved.
-
-
they work fine on Vu+ with the emulator Oscam install that first and we can take you through some configs of setting up the readers
Cccam would be easier to set up but that is hit and miss with latest updates of the m7 group -
Ok,but which one?And where do i have to put it?
- - - Updated - - -
Ok with the oscam.Now i think i need some config?
-
i see that you didn't make an introduction yet on the forum http://linuxsat-support.com/forumdisplay.php/2-Introductions
Goto your ect /tuxbox /config folder/ oscam,server file and edit in this reader
[reader]
label = canaldigitaal
protocol = internal
device = /dev/sci1
services =
caid = 0100
boxkey =
ecmwhitelist = 64
detect = cd
mhz = 450
cardmhz = 2700
ident = 0100:00006A
group = 1
emmcache = 1,3,2,0
blockemm-unknown = 1
auprovid = 00006A
ratelimitecm = 4
ratelimittime = 9000
ecmunique = 1
srvidholdtime = 2000if you have the Motorstvhd+mezzohd channels in your subcription then contact me by pm. this reader is setup for topslot and device = /dev/sci0 would be bottom on my Vu's tv vlaanderen would be the same only ident = 0100:00006A would change to ident = 0100:00006c and auprovid = 00006A to
auprovid = 00006c not sure how much you know of setting up sofare and what image you use. -
Ok with the indroduce.
i see that you didn't make an introduction yet on the forum http://linuxsat-support.com/forumdisplay.php/2-Introductions
Goto your ect /tuxbox /config folder/ oscam,server file and edit in this reader
[reader]
label = canaldigitaal
protocol = internal
device = /dev/sci1
services =
caid = 0100
boxkey =
ecmwhitelist = 64
detect = cd
mhz = 450
cardmhz = 2700
ident = 0100:00006A
group = 1
emmcache = 1,3,2,0
blockemm-unknown = 1
auprovid = 00006A
ratelimitecm = 4
ratelimittime = 9000
ecmunique = 1
srvidholdtime = 2000if you have the Motorstvhd+mezzohd channels in your subcription then contact me by pm. this reader is setup for topslot and device = /dev/sci0 would be bottom on my Vu's tv vlaanderen would be the same only ident = 0100:00006A would change to ident = 0100:00006c and auprovid = 00006A to
auprovid = 00006c not sure how much you know of setting up sofare and what image you use.- - - Updated - - -
I have the blackhole 3.0.2.J,enigma2-plugin-extensions-tspanel_7.3_mips32el.ipk,enigma2-plugin-cams-oscam-9705_blackhole_all.ipk .
- - - Updated - - -
I hope that this is what i must do
74d3ef0.jpg -
If you want to use both cards at the same time, your oscam.server will have to include two reader entries, something like:
Quote
#
# Read more: http://www.streamboard.tv/svn/…/doc/txt/oscam.server.txt
#
# Internal reader upper (or if the box has only one reader)
#----------------------------------------------------------
[reader]
label = upper
enable = 1
protocol = internal
device = /dev/sci0
group = 1
emmcache = 1,3,2
blockemm-g = 1
blockemm-unknown = 1
#below optional entries I've used for TV-Vlaanderen
cardmhz = 500
ratelimitecm = 4
ratelimitseconds = 10
#caid = 0100
#auprovid = 00006C# Internal reader lower (boxes with two readers)
#-----------------------------------------------
[reader]
label = lower
enable = 1
protocol = internal
device = /dev/sci1
group = 1
emmcache = 1,3,2
blockemm-g = 1
blockemm-unknown = 1I have a TV-Vlaanderen card running in the lower configuration.
The upper configuration is a merge from what I had on my previous box, it's still a work in progress and I have to check if it works with more than one channel at a time. -
Ok with the indroduce.
- - - Updated - - -
I have the blackhole 3.0.2.J,enigma2-plugin-extensions-tspanel_7.3_mips32el.ipk,enigma2-plugin-cams-oscam-9705_blackhole_all.ipk .
- - - Updated - - -
I hope that this is what i must do
74d3ef0.jpg
did you try running your dutch card after rebooting your box when changed your oscam.server file ?
When i have some more time i will get a full config setup for cd+ttv if masterg doesn't have one before me but busy at the moment.- - - Updated - - -
If you want to use both cards at the same time, your oscam.server will have to include two reader entries, something like:
I have a TV-Vlaanderen card running in the lower configuration.
The upper configuration is a merge from what I had on my previous box, it's still a work in progress and I have to check if it works with more than one channel at a time.
you will have to assign a caid and provider id in the readers plus m7 group have the 4sid block on their cards wich in basic means that you can only maximum open 4 channels at the one time if you open more your card will kind of lock for a while and glitch and freeze thats why you have to add
ratelimitecm = 4
ratelimittime = 9000
ecmunique = 1
srvidholdtime = 2000 -
To avoid any mistakes,i don't have any server.I only want to have both cards in one receiver.
did you try running your dutch card after rebooting your box when changed your oscam.server file ?
When i have some more time i will get a full config setup for cd+ttv if masterg doesn't have one before me but busy at the moment.- - - Updated - - -
you will have to assign a caid and provider id in the readers plus m7 group have the 4sid block on their cards wich in basic means that you can only maximum open 4 channels at the one time if you open more your card will kind of lock for a while and glitch and freeze thats why you have to add
ratelimitecm = 4
ratelimittime = 9000
ecmunique = 1
srvidholdtime = 2000 -
extract config folder and ftp to tuxbox folder to replace existing config folder.
reboot box and restart your oscam, try your cards, -
What can i said!!!!!!!!!!!It works!!!!!!!!Finally i'm goin' to sleep well!!!
-
like i said before if MotorstvHD+MezzoHD should be part of your subscription p.m. me to get the boxkey set up.
-
master G
Moved the thread from forum Vu+ SOLO2 Support to forum VU+ SOLO 2.
VU+ SOLO 2 PVR Ready Linux Enigma2 Receiver Full HD 1080p
Download VUPlus Images and Enigma2 Team Support from Black Hole, OpenATV, OpenBH, Open Black Hole, OpenDroid, OpenESi, OpenHDF, OpenLD, OpenPLi, OpenSPA, OpenViX, Open Vision, PKT Hyperion, PurE2, SatDreamGR, VTi.
Participate now!
Don’t have an account yet? Register yourself now and be a part of our community!