OSCAM not working after channel scan

There are 3 replies in this Thread which was already clicked 990 times. The last Post () by master G.

    Vu+ Solo 4K; Blackhole 3.0.5L image; OSCAM 11425; Canal Digitaal card; Sattelites 13.0º, 19.2º. 23.5º, 28.2º


    This has happend at least three times before:


    OSCAM works normally and I can get all the coded channels for my card. After I do a manual channel scan of each of the satellites OSCAM stops working and I cannot get my coded channels anymore.


    I do not know how I got OSCAM to start working again when this happend in the past. I tried many things without success and then sudenly OSCAM starts working again. It takes days of trying things, so I do not know what worked. I have uninstalled OSCAM, gone to another version, restarted multiple times etc. etc.


    Anyone got any suggestions? (I am not changing my Blackhole image for another if you are going to suggest that)

    • Official Post

    Don`t bother scanning the satellites. Add catseye settings, which has those satellites. Some satellites will need removed from the settings, but we can do that if it solves your problem.

    Catseye settings can be downloaded from the blackhole addons panel or use the attached version.

    Have you looked at the oscam live log before and after the scan to see if there are any errors that may help ?

    I did not look at the Live Log before this all happened. Now it shows a lot of message similar to:

    (ecm) anonymous (0100@00006A/5C00/5230/64:F976AA857DD149C810DD2D90583D9AA6): not found (10 ms)


    What I have tried:

    Copied over previously WORKING OSCAM files to Vu+ from PC

    Restarted Vu+ & restarted OSCAM (blue key) to be sure


    Switched to Channel 1 NPO1 (Coded channel) ==>> No picture!

    Went to 192.168.0.60:888 (OSCAM details) ==> Status showed:

    Upper ON 127.0.0.1 0 internal 0000:0000@000000 no data OFF(no entitements)

    Lower ON 127.0.0.1 0 internal 5230:0100@00006A NPO3 HD no data CARDOK(no entitements)

    Emulator ON 127.0.0.1 0 emu 0000:0000@000000 no data CARDOK(1664 entitements)


    Status showed upper and lower card readers and an emulator. On the card readers showed theSRVID:CAID@PROVID as

    0000:0000@000000 (upper card) and 5230:0100@00006A (lower card)


    Put the card -Face Down- into the lower slot and restarted OSCAM ==>> No picture!!

    Then showed for SRVID:CAID@PROVID:

    Upper ON 127.0.0.1 0 internal 1B6C:0100@00006A

    Lower ON 127.0.0.1 0 internal 00000:0000@000000

    Emulator ON 127.0.0.1 0 emu 0000:0000@000000

    Put the card -Face Down- into the UPPER slot and on Channel 1 NPO1 and restarted OSCAM ==>> No picture!!


    Then showed for SRVID:CAID@PROVID:

    Upper ON 127.0.0.1 0 internal 0000:0000@000000

    Lower ON 127.0.0.1 0 internal 5230:0100@00006A

    Emulator ON 127.0.0.1 0 emu 0000:0000@000000


    It seems that when I switch cards to the other slot, the SRVID:CAID@PROVID goes to all zeros in the occupied slot and a normal value in the empty slot.


    Also entitelments alway seem to be OFF except for the emulator.


    I am not versed in all this. Can anyone throw some light on the subject?





OSCam Support Forum

Configs, discussion, downloads and guides for OSCam Softcam.

Participate now!

Don’t have an account yet? Register yourself now and be a part of our community!

Register Yourself Login