hi .. i am looking for mgcam 1.38 for pli [enigma 1]dm 500s ..i found some ..but when i transferred it to var/temp folder ..it is showing in box .. so plz some 1 post mgcam 1.38 for pli & guide me how install & make it working in open pli ..
thanx
How to add mgcamd 1.38 in open pli -e1
- vehla_jatt
- Thread is marked as Resolved.
-
-
It should be on the download panel mate. If not
MgCamd1.38_For PLi_E1 -
It should be on the download panel mate. If not
MgCamd1.38_For PLi_E1thanks ..for link ..i have this file ..when i am tranferring it in to var/temp .. folder ..it is not showing in box ..
-
Try this one mate.
-
Try this one mate.
same problem .. ... no luck to see mgcamd folder in box ..
-
I just installed openpli to test this for you and the first file i linked you to is good. Follow this to install it.
1. Download and extract the file to your desktop.
2. Using DCC transfer the complete var folder to your dm500 as shown below.
3. Navigate to var/bin and right click on the MgCamd_1.38 file then select atributes and set permissions to 755.
4. MgCamd_1.38 will now show in your softcam manager.
-
Hi, i have an Openbox S16 and i am looking forward to how to activate MGcam in the main manu.
Only CCcam, Newcamd and KKcam is present in the box menu. Try to assist please. -
thanks ..for link ..i have this file ..when i am tranferring it in to var/temp .. folder ..it is not showing in box ..
hi
you cannot see and install manually from tmp folder that file MgCamd1.38_For PLi_E1 posted by Ten Below because that file ist not tar.gz file.To install manually from tmp folder you shoulkd have a tar.gz file.
I created a tar.gz file from Ten Below posted file and i have not tested but you can do it maybe it's gona work.
here -
Hi, i have an Openbox S16 and i am looking forward to how to activate MGcam in the main manu.
Only CCcam, Newcamd and KKcam is present in the box menu. Try to assist please.hi
you cannot see and install manually from tmp folder that file MgCamd1.38_For PLi_E1 posted by Ten Below because that file ist not tar.gz file.To install manually from tmp folder you shoulkd have a tar.gz file.
I created a tar.gz file from Ten Below posted file and i have not tested but you can do it maybe it's gona work.
hereWhat i posted is how to install this cam 100% manually to a dm500 on open pli, when it comes to openbox i have no idea how these work but given that they are closed source please report back if the tar.gz file is sucsessful as this will allow us to work on some installers for this receiver like we do for others.
-
yes mate you right.if he use an older release PLi image there is a chance but if he use an open pli then i dont know and i dont know if there is a softcam menager or he should install after! but he can try it!
-
Yes, the screenshots were taken from open pli but he is looking to install the cam on an Openbox S16. Noorani456 i think its best you post again in the correct section.
Openbox Support -
Master G,
where must the VAR folder be FTPed to install mgcam on to an open PLI E1 box ?
Images do not show in your earlier post,
cheers -
If you open the folder /var/bin/ you will find an MgCamd_1.38 file. FTP MgCamd_1.38 to /var/bin/ on the receiver.
Same goes for MgCamd_1.38 file in \var\etc\plimgr\cams folder, send it to \var\etc\plimgr\cams on the receiver.
-
Pretty obvious in hindsight.
Thanks mate for reply
MGCamd Support Forum
Configs, discussion, downloads and guides for MGCamd Softcam.
Participate now!
Don’t have an account yet? Register yourself now and be a part of our community!