hi all, can anyone give me setting to run oscam as internal card reader for own card. It should work a reader and server both. Box is dm800se
Oscam internal card setup conax
- vasudev.kamat
- Thread is marked as Resolved.
-
oscam.conf
Code
Display More[global] logfile = clienttimeout = 4000 clientmaxidle = 300 netprio = 1 nice = -1 maxlogsize = 1000 waitforcards = 0 preferlocalcards = 2 dropdups = 1 [dvbapi] enabled = 1 au = 1 pmt_mode = 0 request_mode = 1 user = dvbapi read_sdt = 1 write_sdt_prov = 1 boxtype = dreambox [webif] httpport = 8888 httpshowmeminfo = 1 httpshowuserinfo = 1 httpshowcacheexinfo = 1 httpshowecminfo = 1 httpshowloadinfo = 1 httpallowed = 127.0.0.1,192.168.0.0-192.168.255.255,10.0.0.0-10.255.255.255,::1 http_status_log = 1 [newcamd] port = 10001@0B01:000000 key = 0102030405060708091011121314 mgclient = 1 keepalive = 1 [cccam] port = 12000oscam.server
Code
Display More[reader] label = conax protocol = internal detect = cd device = /dev/sci0 cardmhz = 2700 mhz = 450 emmcache = 1,3,2 group = 1 caid = 0B01 ident = 0B01:000000 rsakey = boxkey =oscam.user
Code[account] user = dvbapi group = 1 au = conax keepalive = 1 -
Did you enter the rsakey and boxkey? These are required for new CAS7 conax cards.
If you don`t have the rsakey you won`t be able to continue any further.
-
Can you tell us which provider you have. Conax caid 0B00 is used with more than one provider.
Do you know if its possible to view this card in oscam?
Are you using the latest oscam?
-
Add the following line to oscam.dvbapi (sometimes it helps with multiple different CAIDs):
P: 0B00
Try changing the emmcache in oscam.server:
emmcache = 0,3,1,0
-
dvbapi_get_packet_size(): error - buffer length (0) too short
This error has been reported recently on streamboard ~ http://www.streamboard.tv/oscam/changeset/11550
Maybe your version of oscam is affected by it. Try the latest version of oscam.
-
Display More
Thanks. Still not working. Getting below error.
2020/01/26 14:56:14 5D072805 c (dvbapi) dvbapi_get_packet_size(): error - buffer length (0) too short
2020/01/26 15:00:17 5D072805 c (dvbapi) Demuxer 0 trying to descramble PID 2 CAID 0B00 PROVID 000000 ECMPID 116C ANY CHID PMTPID 1168 VPID 1169
2020/01/26 15:00:17 5D072805 c (ecm) dvbapi (0B00@000000/0000/578E/6E:8C9334AC0B8D6504BD66D862068E3445): not found (2 ms) by conax - .- .
2020/01/26 15:00:18 5D072805 c (dvbapi) Demuxer 0 restarting decoding requests after 0 ms with 1 enabled and 2 disabled ecmpids!
Did you change the CAID to 0B00 ? Because in the configuration from master G , was used CAID 0B01.
What does LiveLog look like when switching channels to another channel (PROVID and CAID list) ? Please open the OscamWebif and check LiveLog.
What about PROVID ? Is it set correctly ?
What does the initialization of your satellite card look like in LiveLog ?
-
Hi VA and All,
Did you get running.
I was running my card in a PC with oscam and RSA, however because of updating problems I have decided to run my card in a STB with oscam and dish connected. It runs in the box but I want to share it to my PC server. At the moment my PC server UI says its connected to the STB but it is not clearing pictures. Both stb and pc are running oscam.
-
Hi Guyz,
Thanks all. It seems I dont have RSA Key, hence it will not work. Is there any other way to make it work without RSA. Pelase suggest
Different cards uses different configurations, for Conax card you should have RSA key to run in OScam. RSA key can extracted from Dump file, via RS232 or via Programer. but there are different box's and they uses different security systems. May be my method is old. seniors can correct me.
-
Hi,
Thanks for your reply.
Let me explain. The card is running ok in my E2 box using oscam and RSA etc. I want to share this to all my other rooms with my PC which is currently runnin oscam.
-
You can share from stb in another rooms (homesharing)
-
Thanks for your reply.
I was hoping that some forum members here would be able to assist me as I don't want to join another forum site for just one problem. If my back is up against the wall I will follow your link.
Thanks again.
-
Hi,
Thanks for your reply.
Let me explain. The card is running ok in my E2 box using oscam and RSA etc. I want to share this to all my other rooms with my PC which is currently runnin oscam.
you can open port to your DM and add Cccam or Newcamd as per your config 127.0.0.1 port user pass similarly 127.0.0.1 port user pass deskey
-
Thanks bud.
I have it clocking emms at the moment with a config I received from forum member ste141. I don't quiet understand how it works. My stb is running oscam and is connected to my dish which sends the emms to the pc and card. I think it uses cccam protocol for this job but am not sure. Here is a sample of my server in my stb.
Maybe someone will post an explanation of what is actually happening regarding the emm's being updated on my pc.
[reader]
label = PC_Server
protocol = cccam
device = 192.168.5.135,12000
user = hi
password = hi
inactivitytimeout = 30
group = 7
cccversion = 2.2.1
ccckeepalive = 1
-
Thanks for your reply.
I was hoping that some forum members here would be able to assist me as I don't want to join another forum site for just one problem. If my back is up against the wall I will follow your link.
Thanks again.
for home sharing use cs357x protocol
add in conf
OSCam-EMU Support Forum
Participate now!
Don’t have an account yet? Register yourself now and be a part of our community!
