cyfra entitlements

From what I have read you should be able to get this card updated with the methods you have tried already. If you are uncomfortable using the method master G has suggested (but should be easy enough with the guides and configs), then you can try using Oscam alone, with dvbapi. This worked for me to activate a sly card and mtv card that had no active entitlements.

in oscam.user

[account]
user = dvbapi_dreambox
pwd =
group = 1
monlevel = 0
au = 1

in oscam.conf

[dvbapi]
enabled = 1
au = 1
boxtype = dreambox
user = dvbapi_dreambox

in oscam.server

[reader]
Label = cyfra
Protocol = internal
Detect = cd
Device = /dev/sci0 (or /dev/sci1 depending on slot)
EMMCache = 1,3,2
Group = 1 (group has to be the same as the oscam.user dvbapi entry group)
mhz = 357
cardmhz = 357
CAID = 0100
ident = 0100:000068

important!! - in your oscam.dvbapi file - add the following;

P: 0100:000068 1

The above line is very important, and the '1' at the end keeps oscam sending requests to the card, without it, it will give up after a few attempts. The 1 in AU = 1 sends all requests to all cards so for this - I find it works, so best leave it like this until your card updates.

Just back up your old configs first - do above and once updated revert to your previous configs. Not sure what the best channel is to leave it on, but read somewhere that TVP 1 works.

Hi, just to add my two pence worth, I used to have a cyfra card - now expired.
I used it with cccam to update entitlements [it took about 45mins] and was no problem. I also bought it from the same place.
Hope you manage to sort it.

I have no issues with my cyfra+ card updating using Mgcamd 1.35a on a clone dm500, i send the box a CWS line from oscam pc server and in the AU part of user account i put the label name which in my case is cyfra+

However if what you have just done does,nt update your card i can upload my Mg_cfg for you as this is important and wont update your card properly and maybe not at all if its setup wrong!

romman

As per pm here is mg_cfg and configs.

[global]
usrfile = /var/log/oscam/oscamuser.log
logfile = /var/log/oscam/oscam.log
cwlogdir = /var/log/oscam/cw
disablelog = 1
clienttimeout = 3900
nice = -1
maxlogsize = 0
preferlocalcards = 1
saveinithistory = 1

[monitor]
port =
aulow = 120
hideclient_to = 15
monlevel = 1
appendchaninfo = 0

[newcamd]
port = PORT@0100:000068
key = 0102030405060708091011121314
keepalive = 1
mgclient = 1

[webif]
httpport =
httpuser =
httppwd =
httprefresh = 10
httpallowed = 127.0.0.1,192.168.0.1-192.168.0.100,192.168.1.2-192.168.1.100,1.1.1.1-255.255.255.255
httpdyndns =

[reader]
label = cyfra+
description = cyfra
protocol = smartreader
device = 2
showcls = 0
caid = 0100
detect = cd
mhz = 600
cardmhz = 600
ident = 0100:000068
group = 3
emmcache = 1,3,2
auprovid = 000068

[account]
user = CYFRAUP
pwd = CYFRAUP
group = 3
au = cyfra+
caid = 0100
ident = 0100:000068
cccignorereshare = 0
keepalive = 1

If you are using the mg_cfg for client use only with no update change this below to A: { 00 } Its not really required its just i prefer to do this but leave it on 01 to update your card.

# AU
# 00 disable, no emm pids processed
# 01 enable, emm pids always processed for soft-au and shared cards
# 02 auto, emm started only if channel cant be decoded
# 03 process emm pids for network cards update only
A: { 01 }

If I were you I would contact Satsklep first thing tomorrow - you are trying everything that should work and it isn't working, so that emm you are looking for might not be out there.

Good job on getting it sorted bud,at least if others have the same problem all the help and advice is contained in this thread.

Enjoy!

I will close this thread now that the problem has been sorted.