AMİKO ALİEN 2 IDENT ERROR

There are 19 replies in this Thread which was already clicked 1,543 times. The last Post () by ahmed gazye.

  • My friend / samut

    Quietly, God willing, the problem is simple

    First, remove any external flash that is installed on the device


    Second, start with this solution and implement what is contained in it

    Close the device from the power button in the back and Click on the ok from the front of the receiver for 5 seconds, then not leave ok, and

    open the device from power button in the back,Until it Appears on the screen is forc supported you from Ok, then you Click on the channel buttons next to it until the word spark appears on the Ok wait a little while Boot appears and the device will run.


    As it did not respond So it needs a suitable rescue soft 7162




     Good luck



    310271357.gif 310271357.gif
    668584774.png

    310271357.gif 310271357.gif

  • SEVGİLİM AHMed , ı do the same but it is mot spark What is the reason THE TO appears on the screen?


    DEAR AHMed

    Ben aynı şeyi ama nedeni İÇİN ekranda görüntülenir Ne kıvılcım değil?
    Ben aynı şeyi ama nedeni İÇİN ekranda görüntülenir Ne kıvılcım değil?

    Ben aynı şeyi ama nedeni İÇİN ekranda görüntülenir Ne kıvılcım değil?

  • SEVGİLİM AHMed , ı do the same but it is mot spark What is the reason THE TO appears on the screen?


    DEAR AHMed ,

    Do you have loading pictures and why is it THE TO write on the screen?



    dear ahmed , do you looding pictures and why is it TO THE write on the screen?
    Do you have loading pictures and why is it THE TO write on the screen?

  • My friend / samut

    Re-try

    First, remove any external flash that is installed on the device


    Second, start with this solution and implement what is contained in it

    Close the device from the power button in the back and Click on the ok from the front of the receiver for 5 seconds, then not leave ok, and

    open the device from power button in the back,Until it Appears on the screen is forc supported you from Ok, then you Click on the channel buttons next to it until the word spark appears on the Ok wait a little while Boot appears and the device will run.


    As it did not respond So it needs a suitable rescue soft 7162




     Good luck



    310271357.gif 310271357.gif
    668584774.png

    310271357.gif 310271357.gif

    • Official Post

    Make sure you have unzipped everything properly first.

    Use the userfsub.img” & “mImage files, not userfsub.img.tar.gz or mimage.tar.gz.


    CREATE a folder on your desktop called spark (small caps)


    UNZIP the spark rescue image and place the "mImage" and the "userfsub" (Not userfsub.img.tar.gz & “mImage.tar.gz) files into the "spark" folder.


    Follow the rest of the guide i linked above..

    • Official Post

    Please stop also posting this on my wall. Everything should be kept in this thread..

    Does amiko alien 2 usb sticks?

    I already linked the instructions above. But i will post it here again.


    • Now another important factor is when using the rescue image, you must use the rear USB port, not the front.
    • CREATE a folder on your desktop and call it spark
    • UNZIP the spark rescue image.
    • UNZIP userfsub.img.tar.gz & “mImage.tar.gz files.
    • Now place the "mImage" and the "userfsub.img" files into the "spark" folder (Not userfsub.img.tar.gz & “mImage.tar.gz).
    • FORMAT your USB Pen Drive in FAT32, DO NOT choose the quick format as it will not work
    • TRANSFER the "spark" folder onto the USB Pen Drive
    • SWITCH off the receiver at the rear and insert the USB Pen Drive
    • PRESS and HOLD the OK key at the front of the receiver and switch it back on at the rear
    • FORC will appear on the display after a couple of seconds
    • PRESS the RIGHT key FACT should appear on the display
    • PRESS OK key
    • YOU should now see U LD flashing on the display
    • WAIT a good 10 Minutes for the receiver to be back to original factory state (some information on the internet claims that the restore process takes about five minutes, I left mine a bit longer and it worked, so be patient)
  • Added to our supervisor's professor master G comments above


    - Rescue Soft must be installed while you are on the Spark system, not a system enigma2 Until it is accepted

    - It is possible not to accept Soft Rescue from the first times, meaning that you repeat the process once, two and three until it ends and the receiver accepts the software even if it did not succeed. Download another copy of Softrescue until you succeed, God willing,


     Good luck



    310271357.gif 310271357.gif
    668584774.png

    310271357.gif 310271357.gif

  • My friend / samut

    use kingston or sandisk


    FORMAT your USB Pen Drive in FAT32, DO NOT choose the quick format as it will not work

    Follow the steps carefully and try more than once Do not give up

    - Rescue Soft must be installed while you are on the Spark system, not a system enigma2 Until it is accepted

    - It is possible not to accept Soft Rescue from the first times, meaning that you repeat the process once, two and three until it ends and the receiver accepts the software even if it did not succeed. Download another copy of Softrescue until you succeed, God willing,


     Good luck



    310271357.gif 310271357.gif
    668584774.png

    310271357.gif 310271357.gif

  • My friend / samut


    Congratulations for your success in restoring the device system

    You can download it from the forum at the following link


    Spark 1.2.83 for Amiko Alien2 (7162) joeusertopic


    Release Notes for v1.2.83:

    Improvements:

    - Improved YouPorn playback support



    I have not tried it, just noticed it was not posted here yet even though it is almost a year old...




    136115-1999e-png






     Good luck



    310271357.gif 310271357.gif
    668584774.png

    310271357.gif 310271357.gif

  • On my Alien 2 this has happened a couple of times some years ago , the writing "T TO" on the display was due , if I remember well , to a wrong brand of USB stick.

    What I suggest is that you use a 4 GB Trascend formatted in FAT32, try to put on it the most recent image (1.2.83 for Europe) or follow MasterG and Ahmed Gazye's instructions to rescue the decoder . I only use it now to test the images posted in this Forum but since i rescued it has been working with no problems on Spark and Enigma2 partitions.

  • DEAR Alienato MY AMİKO ALİEN 2 STB:0C000A0000101E


    AMİKO ALİEN 2 1.2.86 SOFTWARE DOWLAND LİNK ? THANK YOU

    I've read about this 1.2.86 image but never seen a link to download it , anyway after the rescue Version 1.2.83 Europe was the most up to date image for Spark ,you have just to install it and then try to upgrade but i'm quite sure you won't find what you're lookin' for

  • master G

    Added the Label Image Flashing & Backup Support

Spark STI 7162 Support

Support for Amiko Alien 2, Delta, Dynavision 7162, Galaxy Innovations Avatar 2, Galaxy Innovations Avatar 3, Golden Media Spark Triplex, Golden Media Spark One, Icecrypt S3700 CHD, SAB Unix Triple HD, Samsat Linux 2, Satcom 7162, Sogno Spark Triple, Startrack SRT 2020 HD Plus, Superbox Z500, Truman TOP-BOX, Truman TopBox 2 Tuner, Visionnet Falcon, Spark STI 7162 Receivers.

Participate now!

Don’t have an account yet? Register yourself now and be a part of our community!