Hello, but the end of the file is .deb ?!?
You are not serious, just checked and the file is good
check once more the first post please
Hello, but the end of the file is .deb ?!?
You are not serious, just checked and the file is good
check once more the first post please
Hello, i have this : enigma2-plugin-softcams-ncam_V13.4-r0_all.ipk.deb
i have this : enigma2-plugin-softcams-ncam_V13.4-r0_all.ipk.deb
The problem is occurring during the download.
If you are downloading on a mobile phone use the laptop instead.
If your on the laptop try with a different browser.
Hello, ok thank you. But i always download files with my mobile phone...and i never have this problem. Have a good time GD
But i always download files with my mobile phone...and i never have this problem.
Try deleting the extra .deb that was added to the end of the extension and it should work.
Should be all.ipk not all.ipk.deb
After open (ncam.server) you will see this reader
CodeDisplay More####################### CCcam ############################ [reader] label = Server_1 protocol = cccam device = host,port user = user password = pass group = 1 emmcache = 2,1,2,1 emu_auproviders = 0604:010200;0E00:000000;1010:000000;2610:000000 cccversion = 2.0.11 ccckeepalive = 1 cccmaxhops = 2 # dont use higher than 3 !!! disablecrccws = 1 cccwantemu = 1 blockemm-unknown = 1 blockemm-u = 1 blockemm-s = 1 blockemm-g = 1 audisabled = 1 #DISABLECRCCWS_ONLY_FOR = 1884:000000;098c:000000;09c4:000000;098d:000000;0500:50f000,030b00;1811:003311,003315;1883:003311;1819:00006d;1884:000000 #chid = 0604:0000CC,0000CD,00009C,000020,000085,000086,0500,0604,090F,0E00,1010,1801,2600,2602,2610,4AE1 #services = !powervu_fake,!tandberg_fake,!biss_fake,!afn_fake
And EVERY THINGS Clean in reader ...
in these lines you can add host port username and password
In my case protocol is newcamd with deskeys 01-14 and I have tried many settings and all I get is error1 or timeout message, is the first time I try Ncam to be honest I like how fast the emu auto roll, the only thing I haven't figured it out is the newcamd..........
the only thing I haven't figured it out is the newcamd
the only thing I haven't figured it out is the newcamd
Tried it, it gives me same error, disconnect, not found, I am giving up with Ncam..............Thanks for trying MasterG
All Sharing lines work just fine on Ncam ... you need to add your settings carefully ...
Look in this screenshot it is from newcamed line work without any problem ...
Also You can add you lines in CCcam.cfg or ncam.fs it you got hard work with ncam.server.
Hello, i erase the : .deb after this i install it on ultimo 4k open atv 7.1 but the ncam 13.4r0 are not ok, it's impossible to start it...
Best regards GD
What are talking about ?!!
i erase the : .deb after this i install it on ultimo 4k
1-What did means erase ?!!
2-deb file JUST for Dreambox device and JUST for DreamOS image (not for VU not for Open source image)
3-What did you mean
are not ok, it's impossible to start it...
Did you install ipk file or not ?!!!
Do you have experience with E2 devices ?!!
Display MoreAll Sharing lines work just fine on Ncam ... you need to add your settings carefully ...
Look in this screenshot it is from newcamed line work without any problem ...
Also You can add you lines in CCcam.cfg or ncam.fs it you got hard work with ncam.server.
My provider only uses newcamd with deskeys, ccam won't work, ncam fs never tried it, I just started testing and learning about Ncam, I tried many settings and nothing, I get error1 and time-out and once I got MGS received FF
This is what I get, I have tried ncam.server the settings for newcamd, mg cam that already have the deskeys 01-14 the url and port I replaced with * here in the post, in the live log they appear correctly
If it was working in oscam it will also work in ncam.
Renaming your oscam configs will allow ncam to read them.
oscam.conf to ncam.conf - oscam.server to ncam.server and so on.
Add support for icam on my Ncam source depend on (icb) patches thank you
Hello, using Ncam 13.4r1 for Cygwin 64bit I get these errors non-stop on PowerVu channels on 9.0°E (although the channels DO open correctly):
2022-11-01 20:10:58 3D25C907 r (emu) FATAL ERROR: pthread_mutex_lock() failed in powervu_ecm with error 22 Invalid argument
2022-11-01 20:10:58 3D25C907 r (emu) FATAL ERROR: pthread_mutex_unlock() failed in powervu_ecm with error 22 Invalid argument
Hello, using Ncam 13.4r1 for Cygwin 64bit I get these errors non-stop on PowerVu channels on 9.0°E (although the channels DO open correctly):
2022-11-01 20:10:58 3D25C907 r (emu) FATAL ERROR: pthread_mutex_lock() failed in powervu_ecm with error 22 Invalid argument
2022-11-01 20:10:58 3D25C907 r (emu) FATAL ERROR: pthread_mutex_unlock() failed in powervu_ecm with error 22 Invalid argument
Check de dvbapi oe 1 or 2 or disable
I have tried this with Zgemma H9S PurE2 and Axas HIS Twin Plus OpenATV 7 and no luck, I checked ccam.cfg ncam.fs no luck, anyway it was good to learn about Ncam, it really works on emu and auto roll pretty fast compared with regular oscam.........some day someone will figure out how to make newcamd connect to the server.
P.S. I read in another forum (Arabic) about Ncam and another way to add the newcamd, I haven't tried that one, will report if it works.........
Hello, i used ncam-13.2 actually...and i have never problems to download all the version befor...to install them...so why you think i have no experience?!? and you? ...fairbird. Best regards GD
Don’t have an account yet? Register yourself now and be a part of our community!