DM920 oscam can't read viaccess card?

There are 16 replies in this Thread which was already clicked 2,078 times. The last Post () by NenadX.

    hello,


    I never can read a viacess card wih oscam and DM920, i tried a lot off different cam and does'nt work.

    With the same config no problem with a Vu+ zero


    osacam.conf:

    [dvbapi]

    enabled = 1

    au = 1

    boxtype = dreambox

    user = dvbapi


    oscam.server:

    [reader]

    label = CH

    enable = 1

    protocol = internal

    device = /dev/sci0

    caid = 0500

    detect = cd

    #autospeed = 1

    group = 1

    #emmcache = 1,1,2,0

    #emmcache = 1,3,2


    here is the logfile with the DM920


    Is these line normal if a have a DM920?

    2020/05/27 19:27:44 4C21FEF5 r (reader) viacess_card [internal] Reader sci internal, detected box type: vuultimo

    DM920 4k UHD, OpenPli 8.3; Vu+ zero, OpenBlackhole 5.1.012; Vu+ zero 4K, OpenBlackhole 4.3.032

    Thank you for the answer.

    I tried with a lot of diferent oscam, no problem with Vu+ zero 4K. Just now i have on the two box this oscam:

    oscam-svn11579-solo4k-webif-dvbapi-emu798

    but i had for exemple this one too:

    oscam-svn11546-arm_v7-webif-dvbapi-emu797-upx,

    oscam-svn11579-arm_oe_ssl102t-webif-dvbapi-ssl-libusb-emu798

    all time the same result!


    oscam.conf:

    oscam.user

    Code
    [account]
user = localuser
#pwd =
group = 1,2,3
au = 1

    oscam.server

    [reader]

    label = viaccess-card

    enable = 1

    protocol = internal

    device = /dev/sci0

    caid = 0500

    detect = cdgroup = 1

    #emmcache = 1,1,2,0

    emmcache = 1,3,2


    or:

    oscam.conf

    with


    oscam.user

    Code
    [account]
user                          = dvbapi
pwd                           =
group                         = 1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16
uniq                          = 3
au                            = 1

    DM920 4k UHD, OpenPli 8.3; Vu+ zero, OpenBlackhole 5.1.012; Vu+ zero 4K, OpenBlackhole 4.3.032

    the same result :-(, here is the log file:

    DM920 4k UHD, OpenPli 8.3; Vu+ zero, OpenBlackhole 5.1.012; Vu+ zero 4K, OpenBlackhole 4.3.032

    Maybe the end is strange?

    2020/05/28 11:07:43 79CBC6A1 r (reader) viacess_card [internal] Error activating card.

    2020/05/28 11:07:44 79CBC6A1 r (reader) viacess_card [internal] THIS WAS A FAILED START ATTEMPT No 1 out of max allotted of 1

    2020/05/28 11:07:44 79CBC6A1 r (reader) viacess_card [internal] card initializing error

    2020/05/28 11:07:44 00000000 s (main) init for all local cards done

    2020/05/28 11:07:44 00000000 s (emmcache) loaded 0 emmcache records from /tmp/.oscam/oscam.emmcache in 0 ms

    2020/05/28 11:07:44 00000000 s (emmcache) loaded 0 emmstat records from /tmp/.oscam/oscam.emmstat in 0 ms

    2020/05/28 11:07:44 2D84FF44 c (client) plain dvbapi-client granted (localuser, au=auto (25 reader))

    2020/05/28 11:07:44 2D84FF44 c (dvbapi) dvbapi channelcache loaded from /etc/tuxbox/config/oscam.ccache

    2020/05/28 11:07:44 2D84FF44 c (dvbapi) Detected /dev/dvb/adapter0/demux0 Api: 0, userconfig boxtype: 1 maximum number of filters is 64 (oscam limit is 64)

    2020/05/28 11:07:44 2D84FF44 c (dvbapi) Detected /dev/dvb/adapter0/ca0 device, total available descramblers: 8

    2020/05/28 11:07:49 2D84FF44 c (dvbapi) Demuxer 0 found 0 ECM pids and 6 STREAM pids in CA PMT

    DM920 4k UHD, OpenPli 8.3; Vu+ zero, OpenBlackhole 5.1.012; Vu+ zero 4K, OpenBlackhole 4.3.032

    No, this card has no problem, it run very good on the vu+ zero 4K with some different oscam like this one oscam-svn11579-solo4k-webif-dvbapi-emu798

    DM920 4k UHD, OpenPli 8.3; Vu+ zero, OpenBlackhole 5.1.012; Vu+ zero 4K, OpenBlackhole 4.3.032

    On the DM920, i tried some differents image, all time the same result.

    is it normal "detected box type: vuultimo"?

    2020/05/28 11:07:09 79CBC6A1 r (reader) viacess_card [internal] Reader initialized (device=/dev/sci0, detect=cd, pll max=27.00 MHz, wanted mhz=4.50 MHz)

    2020/05/28 11:07:09 79CBC6A1 r (reader) viacess_card [internal] Reader sci internal, detected box type: vuultimo

    2020/05/28 11:07:09 79CBC6A1 r (reader) viacess_card [internal] card detected

    DM920 4k UHD, OpenPli 8.3; Vu+ zero, OpenBlackhole 5.1.012; Vu+ zero 4K, OpenBlackhole 4.3.032

    It’s not really right

    detected box type: vuultimo"?

    maybe flash clean again and install oscam with readers configs and initial

    you can use Boxpirates Panel there are all oscam and configs included, when you use OpenATV then have Softcamfeed and oscam-Smod this soft can read card automatically.

    Riquet065 : stupid question, do you have inserted the smartcard in the right direction? In the DM920 the Chip needs to face upwards (on the top). It‘s different to all other Dreamboxes.

    Regards, rako123


    Box 1: Dreambox DM920 UHD, DreamOS + GP4

    Box 2: Dreambox Two, DreamOS + GP4

    Box 3: Dreambox One UHD, DreamOS + GP4

    Quote from rako123

    Riquet065 : stupid question, do you have inserted the smartcard in the right direction? In the DM920 the Chip needs to face upwards (on the top). It‘s different to all other Dreamboxes.

    No, it's not a stupid question!!!!

    I tried the two sides and no side run. When i saw the place i finally put the card with the chip bottom, so not on the good side!

    Now you tell me the good side and all is ok with the .atari. config.

    After i tried again with my original config and run too. I don't know why at the start, before i wrote this post, when i have tried the two sides i hadn't success, maybe that wasn't a good oscam.


    Well, thank you very much to you and thank very much .atari. for your help and your patience.

    DM920 4k UHD, OpenPli 8.3; Vu+ zero, OpenBlackhole 5.1.012; Vu+ zero 4K, OpenBlackhole 4.3.032

    Like 2
    Quote from rako123

    Riquet065 : stupid question, do you have inserted the smartcard in the right direction? In the DM920 the Chip needs to face upwards (on the top). It‘s different to all other Dreamboxes.

    It is not stupid at all. It was just that in my case. :laugh1: :rasta2bigsmoke0gf1:

OSCam Support Forum

Configs, discussion, downloads and guides for OSCam Softcam.

Participate now!

Don’t have an account yet? Register yourself now and be a part of our community!

Register Yourself Login