Flashing problem Amiko Viper 4K V30

sw za oporavak u usb,isključiti iz struje i kad uključiš odmah stisnuti zeleno dugme na daljinskom

sw za oporavak u usb,isključiti iz struje i kad uključiš odmah stisnuti zeleno dugme na daljinskom

...............................................................................................................................................................................

recovery sw in usb, unplug it and when you turn it on immediately press the green button on the remote

I have the XML file to save or recover Viper V30 ! it refers to the EMMC content !

does not contains the missing device table ! I also have the "brute force" copy of

first 64 Mb of EMMC from a working V30 ! if restored does not change anything !

What is so difficult to understand ? the info is not there !!!

Adapter ch340 usb uart to ttl .

The amiko viper v30 is blocked on boot .

IMG_20251112_143025 (1).jpgIMG_20251112_143025.jpgIMG_20251112_143045 (1).jpgIMG_20251112_143045.jpgIMG_20251112_145208 (1).jpgIMG_20251112_145208.jpg

Did you power-on the board as requested ?

the images shows the board off the power !

ho messo i fili nero bianco verde sono inesperto. Se possibile te la spedisco con pacco postale.

No ! is too complicated ! I'm living in Romania !!!

the box does'n value the price of transportation !!!

- the 3 cables are for communication between board and PC

- you need to connect also the power supply to the board !!!

- and the Network cable for bulk transfer

Probably this is too much for your experience !

First you must describe how you get in this status !!!

andato in blocco e continua a fermarsi al boot resta logo di avvio

sembra problema software.

OK ! try this ...

1. unpack the archive , put usb_update.bin on FAT32 stick

https://mega.nz/file/q0MliRZL#35HMWD4RSAM82f6woE8m8NhAaoXcCjXkyppM-QFJchw

2. load it to V30 using Green button method

3. download OpenATV image and unpack it on FAT32 stick

4. load it to V30 using Green button method

How to USB flash New Multi-boot recovery menu and Image to Amiko Viper 4

You will need a USB stick formatted FAT32. I've personally test a number of sticks from 2GB to 64GB. Some sticks can be problematic and fail to be recognised correctly. If you face an issue with the USB stick not being recognised, try formatting FAT32 with 'Mini Tool Partition Wizard' Free edition:

hxxps://www.partitionwizard.com/free-partition-manager.html

1) Download recovery_emmc.zip for your model receiver from hxxps://www.openvix.co.uk/index.php/downloads/amiko-images/amiko-viper-4k/

2) Extract the zip file.

3) In the extracted file you will see the following files:

apploader.bin

bootargs.bin

fastboot.bin

imageversion

usb_update.bin

4) Copy the above 5 files directly to root of your USB stick.

5) Ensure your receiver is powered off and connect USB stick to USB port on your receiver.

6) Amiko Viper 4K hold down REAR reset button and power on while hold this down.

Once UPDT appears on front screen release reset button or power button, whichever applies to your receiver.

Once booted into the new recovery menu you will see the screen below. ENSURE YOUR USB STICK IS FULLY MOUNTED, SEE TOP RIGHT CORNER FOR USB STICK USED IN THIS EXAMPLE. IF YOU DO NOT SEE /mnt/HDD0 XXXX free DO NOT PROCEED, YOUR USB STICK IS NOT FULLY DETECTED. TRY RE-FORTMATTING THE STICK USING 'MINI TOOL PARTITION WIZARD'. NOTE WINDOWS 10 FORMATING CAN HAVE ISSUES:

7) IMPORTANT, YOU MUST DO THE FOLLOWING THE FIRST TIME TO ENSURE RECOVERY MULTI-BOOT MENU IS FLASHED TO YOUR RECEIVER & CORRECT PARTITIONS INSTALLED. SELECT 'FLASH RECOVERY IMAGE' > PRESS OK AND ANSWER YES WHEN PROMPTED.

8) Once completed your receiver will boot into your previously flash image. If the receiver gets stuck on boot it just means you need to flash a new image. Either way NEW IMAGE HAS TO BE FLASHED.

9) Due to flash partion re-sizing you now need to flash a new image.

10) Power off, BUT ENSURE RECOVERY IMAGE FLASHING IS COMPLETED BEFORE POWERING OFF.

11) Download the image ZIP file for your receiver. Image zip file ends in simply 'mmc.zip'.

12) Copy the complete 'ZIP' file to root of USB stick, DO NOT UNZIP.

13) Amiko Viper 4K hold down REAR reset button and power on while hold this down.

Once UPDT appears on front screen release reset button or power button, whichever applies to your receiver.

Once booted into the new recovery menu you will see the screen below. ENSURE YOUR USB STICK IS FULLY MOUNTED, SEE TOP RIGHT CORNER FOR USB STICK USED IN THIS EXAMPLE. IF YOU DO NOT SEE /mnt/HDD0 XXXX free DO NOT PROCEED, YOUR USB STICK IS NOT FULLY DETECTED. TRY RE-FORTMATTING THE STICK USING 'MINI TOOL PARTITION WIZARD'. NOTE WINDOWS 10 FORMATING CAN HAVE ISSUES:

attachment.php

14) Select 'USB Multiboot Image Upgrade' > Press OK > You'll then see the following screen. At the top you will see the image zip file. In the field below you can select an eMMC slot to flash the image to. For this guide we are selecting Slot 1 where there is currently an OpenViX image installed. We will re-flash this slot. Select 'Start Upgrade' once ready and press OK.

Good luck

In italy where is assistant office amiko viper ......

you can do it as described by me ! just try !