There are 80 replies in this Thread which was already clicked 30,143 times. The last Post () by GamingPulse.
BAD LUCK AGAIN
Here are the screenshots and photos
ThanksIMG_20230218_233846_1.jpg
Errors according to the pictures sent from you
There is an error connecting the internet cable between the receiver and the router, or your internet is weak
Do not mark the non-existent file as softwareinfo. loaderdb. trustedcore
canceled the mark in beside him
The best solution is to use the serial method, despite the long time, but it works Or review internet connections and speed
notice / Internet must be fast in order to be able to complete the process, especially when burning the rootfs.ext4 file, as its size is large, more than 500 MB.
burning can be used by serial, it is the same cables and method, but choose Serial with the hitool program instead of Network, but burning may take more than 3 hours, and the process also succeeds in this way
What ever i tried my friend Ahmet is always stacking in fastboot file......it doesn't pass as u see
I try also to UNSELECT these 3 files u mention
Tried also with serial only same result
i have Fast internet yes but what we need FAST internet i don't understand because if i understand correct we trying to upload Local files to the box from pc
I also test direct from PC to sf8008 same exact result
BIG thanks for ur help
What ever i tried my friend Ahmet is always stacking in fastboot file......it doesn't pass as u see
I try also to UNSELECT these 3 files u mention
Tried also with serial only same result
i have Fast internet yes but what we need FAST internet i don't understand because if i understand correct we trying to upload Local files to the box from pc
I also test direct from PC to sf8008 same exact result
BIG thanks for ur help
Try again & Do not mark fastboot canceled the mark in beside it
Do not mark the non-existent file as softwareinfo. loaderdb. trustedcore
canceled the mark in beside him
Ahmet arkadaşım ne denediysem fastboot dosyasında birikiyor...... gördüğün gibi geçmiyor
bahsettiğin bu 3 dosyanın SEÇİMİNİ KALDIRmaya da çalışıyorum
seri ile de denedim sadece aynı sonuç
bende Hızlı internet var evet ama HIZLI internete ne ihtiyacımız var anlamıyorum çünkü doğru anladıysam Yerel dosyaları bilgisayardan kutuya yüklemeye çalışıyoruz
Ayrıca doğrudan PC'den sf8008'i test ediyorum aynı kesin sonuç
BÜYÜK yardımın için teşekkürler
Find out the IP address of the device via the modem, write it to the desired place in the program. will be uploaded.
Hello
I am looking for hitool dump file for Qviart dual 4k device
would you share?
Merhaba
Qviart dual 4k cihazı için hitool döküm dosyasını arıyorum
paylaşır mısın?
HiTool-5.3.1.2- OV
Display MoreMerhaba
Qviart dual 4k cihazı için hitool döküm dökümü arama
paylaşır mısın?
HiTool-5.3.1.2- OV
I opened the Hitool application, which selection should be in the flash box?
Display MoreDisplay MoreMerhaba
Qviart dual 4k cihazı için hitool döküm dökümü arama
paylaşır mısın?
HiTool-5.3.1.2- OV
I opened the Hitool application, which selection should be in the flash box?
Octagon sf8008 4k twin ( Chipset 3798MV200 )
sungate titan4k octagona sf8008 adapted software thrown
How can I overcome this problem? I tried to throw the rs232 HiTool-STB-5.0.8 sf8008_2018-09-22 parts but as in previous attempts I was not successful.
defineos 06.47 problem
E2 slot1 openatv emmc image no problem other slots mmc problem
Software have a Protection you use
the sf8008 software checks if it is an original sf8008 if not you get this message, the protection is located in the loader
Yazılımda bir Koruma varsa, sf8008 yazılımını kullanırsanız,
orijinal bir sf8008 olup olmadığını kontrol eder, değilse bu mesajı alırsınız, koruma yükleyicide bulunur
I use the original and get the same response.
Your problem is that you uploaded a modified image to another device ( sungate ) on your device sf8008. Try first Erase all of your device with Hitool Then pass The original Full-dump sf8008
This dump is in a forum topic by one of the members najdine at the following link
(openatv-7.5 - 20240914 python: 3.12.5)Or on the following link also from najdine
https://www.mediafire.com/file/pae0...-20240925-Hitool-Full-dump-by-TBs-tn.rar/file
Even though I erased the NAND flash with hitoll and uploaded the full dump in the link, we are stuck on slot1 openatv-7.5-sf8008-20240916_mmc image. The problem still persists in other images loaded in slots 2-3-4, also defineOS is loaded in the image. I continue to get the Factory test message and the annoying error message.
Hello,
I am looking for hitool dump file for sf8008 MINI device.
Would you SHARE? PLS, THX
Hello,
I am looking for hitool dump file for sf8008 MINI device.
Would you SHARE? PLS, THX
I do not have any file for this device. Try searching on Google
I need dump novaler pro
====================
used dump novaler 4k ...........And the result was failed to downlod fastboot
Looking at the logs, it appears that I was using files from a Dinobot 4K Repair-Boot folder. This confirms a hardware/firmware mismatch. Even though these receivers look identical, the Novaler 4K Pro has a different secure boot configuration (Key Area) compared to the standard Dinobot 4K or the basic Novaler 4K models. HiTool blocks the flash because the signature in the fastboot.bin does not match the processor's secure zone.
1. Correct Partition XML: I need the specific eMMC Partition File (.xml) and fastboot.bin specifically designed for the Novaler 4K Pro. Using files from Dinobot or the standard 4K model will continue to trigger the "Key Area" verification error.
2. Isolate the Fastboot Flash: Instead of flashing the entire partition table, I will attempt to flash only the fastboot partition.
fastboot checkbox.3. Transfer Mode Adjustment: Currently, I am using Network transfer mode. If the issue persists, I will switch to Serial (RS232) mode for the fastboot partition. While significantly slower, it is often more reliable for bypassing verification loops during initial bootloader recovery.
"Does anyone have the Original Factory HiTool Dump or the Partition XML + Fastboot files specifically for the Novaler 4K Pro? I need to avoid the generic Dinobot/Novaler 4K files as they are causing signature mismatches. Any help or links to the official Algerian support files would be greatly appreciated."
Looking at the logs, it appears that I was using files from a Dinobot 4K Repair-Boot folder. This confirms a hardware/firmware mismatch. Even though these receivers look identical, the Novaler 4K Pro has a different secure boot configuration (Key Area) compared to the standard Dinobot 4K or the basic Novaler 4K models. HiTool blocks the flash because the signature in the
fastboot.bindoes not match the processor's secure zone.Steps for Resolution:
1. Correct Partition XML: I need the specific eMMC Partition File (.xml) and fastboot.bin specifically designed for the Novaler 4K Pro. Using files from Dinobot or the standard 4K model will continue to trigger the "Key Area" verification error.
2. Isolate the Fastboot Flash: Instead of flashing the entire partition table, I will attempt to flash only the fastboot partition.
- Load the correct XML for the Pro model.
- Select only the
fastbootcheckbox.- If the fastboot flash succeeds, the receiver should be able to reach a state where it can be updated via a standard USB recovery image
3. Transfer Mode Adjustment: Currently, I am using Network transfer mode. If the issue persists, I will switch to Serial (RS232) mode for the fastboot partition. While significantly slower, it is often more reliable for bypassing verification loops during initial bootloader recovery.
Request for Community Help:
"Does anyone have the Original Factory HiTool Dump or the Partition XML + Fastboot files specifically for the Novaler 4K Pro? I need to avoid the generic Dinobot/Novaler 4K files as they are causing signature mismatches. Any help or links to the official Algerian support files would be greatly appreciated."
I actually used the original file for novaler pro of image egami
From the link below
And it didn't work
https://image.egami-image.com/11.0/index.php?open=novaler4kpro
Don’t have an account yet? Register yourself now and be a part of our community!
