my decoder stopped responding after installation, that's a shit, I have the command no CW FOUND !!! original decoder,
i don't have a null modem cable, what should i do now ...
you have to find the null modem cable ,
it depends on the model of the decoder the interface changes from model to model .
You should use the JapharFlasher software.
Just search on amazon or ebay and the null modem plug you find it easily .
on youtube you can find the procedure for resetting with JapharFlasher.
For curiosity send me the photo of the decoder I have several from 2010 upwards.
They can be recovered with the procedure you find on youtube.
Greetings, hello.
These types of decoders have inside them a sim like that of the mobile that you have to program with firmware .
New FIRMWARE does not work well...
As decoders they are quite good ,
they do not have much memory .
As decoders they are quite good ,
they do not have much memory .
But I think you can use them as terminals together with other decoders more Powerful.
Display Moreyou have to find the null modem cable ,
it depends on the model of the decoder the interface changes from model to model .
You should use the JapharFlasher software.
Just search on amazon or ebay and the null modem plug you find it easily .
on youtube you can find the procedure for resetting with JapharFlasher.
For curiosity send me the photo of the decoder I have several from 2010 upwards.
They can be recovered with the procedure you find on youtube.
Greetings, hello.
These types of decoders have inside them a sim like that of the mobile that you have to program with firmware .
oh my god.What have you been doing here?.do you understand what a person writes to you? 
..the receiver is original , so he needs a dreamup program and a loader for the original ssl84 sim . you have laid out so much extra that a simple user can turn a receiver into a brick...
"MAKE A FOOL PRAY TO GOD, HE'LL BREAK HIS FOREHEAD" 
my decoder stopped responding after installation, that's a shit, I have the command no CW FOUND !!! original decoder,
i don't have a null modem cable, what should i do now ...
Need a mini USB cable, and a Lan cable connected to the Internet!
install the drivers in the computer download the link
loader for your SIM card in the attachment
and download the program to install the loader from the link
here in YouTube some Arab posted a video, but you can not listen to his comments on the action on the video everything is clear how and what to do
Watch the best program for Sunray 800 hdse triple tunner sim a8p sim 2.10-2.20 and JapharFlasher_1.1 Null modem cable or with http
dude first, my post is not addressed to you, but to the specialist who mixed both people and horses...the second where did you see in the receiver 800se rs232? that 's just the Null modem cable is under the sr232 section .or are you as "smart" as lamannadavid?
ask google what a null modem cable is, it will give you a picture and then everything will become clear to you
and to restore the 800se, you need a usb- miniusb cable
for DB800SE you need this cable, and then with my guide is easy to unlock! (sorry if I made the guide in Italian, but there are pictures and I think it is NOT difficult
Okey guys.... I say to you both. Arguments and discussions are very much allowed.
But the type of language in use is not.
So I will delete this off topic post and you can both have a nice 
to cool of a bit please
Regards
Seagen
my decoder dm800hd if and dm800 hd
with this procedure work quite well ,
the decoder dm800hd has the rs232 socket .
for this I said that it takes a null modem cable .
No dirty linguggio .
But always Clean Language please.
Thank you.
the program to communicate
with the decoder uses the com port even if it is usb.
So even though it is USB it is seen as a COM port by the computer.
Not to contradict the statements of someone who says it is not null modem cable.
you are a cable that serves to communicate the decoder with the decoder .
So without using a modem . For this it is called null modem cable .
even if it is USB does not change the meaning .
For this decoder, which has a little bit of memory,
you have to eliminate all that is not needed. That's why it might not work.
But whoever says that making a mistake with the firmware risks
making the decoder a brick is very wrong.
Because you can always do an extreme reset with the software.
and start all over again. The great geniuses do not exist.
By doing tests you can find the solution.
My decoders after trying several firmware now work perfectly.
My decoders have not become bricks as some say ...
Edison,
trying and trying many times,
invented the light bulb ...
You mustn't give in to failures ...
Making mistakes you learn ....
I thank everyone for the valuable advice.
It is always a pleasure to learn new things.
I'm never stop learning.
Hello everyone, based on my experience with the dreambox 800se orig / a8p and clone sim 2.10, if the decoder is in no-cw-found it can be recovered usually goes in no ca found because you put the wrong software or why not has the right bootloder (SSL), it happened to me a lot of times to send it in no cw found, but with the miniusb cable, that is the one in the photo put by a user (Archimede)) in the previous posts, you can connect to the miniusb port, send the right software and you have solved your problem, it will take a lot of time, because it is not like installing it via lan or via webinterface that in a couple of minutes the done, it will take you about ten minutes, sometimes you can restore it even if it is in no-ca found by sending the right (SSL) or bootloader, it is important that the software you send to the dreambox is actually for that type of receiver
Hello everyone and happy May 1st, however now you have enough information from different users with which to restore your dreambox
Good fun
I recommend installing flashexpander, so that if you want you can install other images in multiboot, tested and they work great, you can also install epg / picon / other skins /, as long as you have previously installed a formatted usb stick, all tested and working, I also installed Weather plugin and it works perfectly
WHEN I PUT A FIRMWARE OF THE DM800HD SE OF FIRMWARE 2010
THE DECODER DREAM 800HD SE WORKS EXCELLENTLY
EVEN IF THE APPS CAN NOT BE UPDATED .
SO A QUESTION TO THE GENIUSES WHO BELIEVE THEMSELVES TO BE GOD ON EARTH ...
HAVE A LITTLE HUMILITY AND MODERATE THE WORDS !!!
my decoder dm800hd if and dm800 hd
with this procedure work quite well ,
the decoder dm800hd has the rs232 socket .
See the name of the receiver in this topic in the screenshot,why all this stupid talk about what anyone has ? I have both dm800hd and dm800 se, dm800 se v2,dm820,dm900uhd and what to write about all receivers in this topic, how to restore the receiver?
Display Morethe program to communicate
with the decoder uses the com port even if it is usb.
So even though it is USB it is seen as a COM port by the computer.
Not to contradict the statements of someone who says it is not null modem cable.
you are a cable that serves to communicate the decoder with the decoder .
So without using a modem . For this it is called null modem cable .
I repeat .. there is a null modem cable and there is a usb-mini usb, and these are completely different things. regardless of which compote they are connected to.. stop mixing everything into one pile.
Problem solved by mini usb , Thanks for support guys,I didn't want to cause a storm, if I managed to do it, I'm sorry, it was the first time I had such a case and I panicked a bit, everything is back to normal :)
Problem solved by mini usb , Thanks for support guys,I didn't want to cause a storm, if I managed to do it, I'm sorry, it was the first time I had such a case and I panicked a bit, everything is back to normal :)
Do not pay attention, "truth is born in a dispute." some users give a lot of unnecessary information and attachments. after reading and understanding your message.they draw the wrong conclusions and conclusions.
I am glad that you have restored the receiver's functionality. good luck!!
Don’t have an account yet? Register yourself now and be a part of our community!
