Willkommen an alle neuen
Posts by Archimede®
-
-
sorry to intrude, why is the card NOT visible with a viaccess CAM?
-
please make good use of them !!!
otherwise for next time you will NOT find them anymore 
The page is gone.. is it finished? or new link?
Sorry, I changed the link and the current one is this one ======> https://pastebin.com/raw/0zSBtAHa
-
check the 10th item ===>High bitrate support if it is set to YES
-
Dear friend Piterfree, I am sorry I cannot help you, because I do NOT have this receiver, otherwise as you know I would have tried it too.
Only on the ones I have tested in mine and have been successful so far:
Octagon 8008
VU+Solo2
Vu+Solo4K
-
Ich wünsche Ihnen und Ihren Familien ein frohes und friedliches Weihnachtsfest
-
Go to plugin ====> Systemplugings and download ======> s
CodeThere is no tmp option under software manager where I can see the IPK
open Plugin and go to Software Management and then to 5 Install local extensions and see Memory /tmp
-
I usually download oscam from the plugin panel ===> softcam ===> oscam and then with the program DCC_E2 or similar (Filezilla) I edit it
it's easier at least for me ...
-
Go to plugin ====> Systemplugings and download ======> softwaremanager
-
I have just tried it on several VU Solo4K, VU Solo2 , Octagon 8008 receivers and several oscams from an old 11719 up to the current 11726 and it works without any problems on my side as you can see
and the images :
Open PLI 9.0
Open PLI 8.3
Open eight -
as I had replied here :
linuxsat-support.com/thread/?postID=762415#post762415and translated perhaps you understand better
then as I repeat I use the VU+ Solo4k and Solo2
and I use the Open PLI image from an old one up to the current one for SRG+ CAM
and I do NOT think it is different from Kabelio
-
Willkommen an alle neuen
-
Exactly, if you're not using the same CAM of whom is claiming the issue, probably it's working with your CAMs and not with the black one...
Yes I have it, VU+ Duo 4k SE, honestly is really good but not perfect when passing between the two cams, but I cannot address if the issue is related to the box or to the image or the cam. is a little bit OT here but I can give you more details if you need them.
yes I confirm, it is a little slow, but also with other images I have already tested
but the important thing is that it is recognised
-
strange on mine it works without problems, and it is NOT fair to judge the author of the programme when it works.
and you can also see it from the picture I put above
-
183D ok +183E
my collection
-
Thank you very much for answer and I will try following your recommendations to do this
have you solved it ??? I have just done another test again as you can see
-
works without problems, tested on VU+ Solo4K and Solo2 with the Open BH openbh-5.3.011
with this plugin =====> enigma2-plugin-extensions-ci-plus-helper-openbh-openvix_5.x_all
In that post it looks like you're talking about the old HD cam, not the black 4k one that is giving problems to us, am I wrong?
First of all, the old CAM, as you said, is the only one that does NOT need a plugin because it is recognised immediately... whereas WEcam and the other HDs need a plugin otherwise you will NOT have light here I show you the old one that does NOT need a plugin
-
If you say that it works very well then, please answer me, why where does the message constantly appear that check the settings of the module and antenna? Don't write what you don't know it works no very well everywhere and wit all CI plus module and all cards
perhaps to make you understand better, in the past I had done some tests on the Cam and you can find it here ... =====>VU+ Solo2 test with CAM Tivusat HD...
I state the facts and I can prove it to you with evidence
-
works without problems, tested on VU+ Solo4K and Solo2 with the Open BH openbh-5.3.011
with this plugin =====> enigma2-plugin-extensions-ci-plus-helper-openbh-openvix_5.x_all
-
Willkommen an alle neuen
