DM800HDse (Clone from Sunray SIM2/2.10) No Ca Found

Reboot your router/modem,

Use the JapharFlasher and be sure you use a correct IP address in your network for the laptop/pc AND also for the box to set it to a correct IP on your network (and not one that is outside the range of your network).

You must use both, usb cable to service port AND RJ45 to your router. Check your cable RJ45 to be sure it is not damage and work for other things.

TS

1* what system do you have on your pc,

2* if you have installed the windows drivers for mini usb,

once you have done this from the pc usb settings...you have to give it the port you want to use (you can change it as you like)

once this is done, turn off the 800se, start JapharFlasher which will find the port that it will find 1...2...3...4...the one that you will have set on the PC if you did 1...2...3...4 now turn on the 800se from the switch and wait for the version that will recognize you to appear on JapharFlasher the best.

If all is GOOD and FULLY working... ask you why it doesn't work... with 2 boxes.

If you don't want to do what we tell you, why asking ?

We have a LONG experience, routers are buggy, ... I hope that by now you know it by experience (which we do, us).

When you tell NO CHANCE, etc... and you have a problem you will continue to have the problem if you continue to tell NO CHANCE... as you canot CHECK EVERY PART that you use, as if it doesn't work one of the chain part is not working at least or few, and ONLY if you do check EVERY part of the chain you can find out...

I am done, if you don't want to do things we tell you, and you are sticking that all works, but it doesn't work... where want you to go ? Nowhere...

TS

Quote from tiku_2

toysoft

Why do I have to reboot my router? , I have one working DM800hd which i revived with same RJ45 cable few days back, its still getting detected if i connect using Dreamup, Sunray Flasher.

Also when i power up working dreambox I can see the new ip in the DHCP Client Menu of my router setup but thats not the case with these two. So no chance of damaged cable.

piterfree

I am using Windows 10 everything is installed correclty as i said if i connect mini usb it gets detected in Device Manager, morevover I just revived one DM800hd with same cables 2-3 days back.

Display More

hi, you are completely wrong...800 does not have mini usb but Com and you are using a virtual Cam port and not the driver for mini usb port for Dreambax 800se they are 2 different options and Windows 10 I think you do not know how to use it if you confuse these 2 ports.

IMG_20241205_125923~3.jpg

It's not a fantasy, we've been using 800 and 800se for 20 years

800

800se...???

make flesch 800 via Lan for 800se (sim) with mini usb driver+ Lan...!!

DM 800 is not the same as 800se there are different drivers for the flesch ok...maybe you don't know.

Quote from tiku_2

piterfree

No sir 800 clone don't have a RS232, Infact it has mini usn port which is printed service on it, and it is use for communicating with the box Usb-Uart.

toysoft

Ok i rebooted the router, connected all the cables, used Jaspher v 1.1, but still no Luck, No Response from the box But the Display LCD Says No Ca Found, where as again connected working DM800 in jaspher flasher and it initiated http; Box Detected dm800 and the green bar goes full.

you quoted 800 then you say 800if...???...what are you doing is unknown.

DM 800se

Screenshot_20241205-195343.png

DM 800

Screenshot_20241205-195624.png

hi,try this OptiFlasher v1.0.3 Enigma2 EDition By YASSINOV

we have decades of experience these are the decoders that we ate for dinner and breakfast and even slept on top of the decoder...and this is also the best way to rewrite the Sim, but if you don't listen to us it's better to leave it alone.

IMG_20241208_102325.jpg

IMG_20241208_103007~2.jpg

here he goes

Quote from tiku_2

Quote

you quoted 800 then you say 800if...???...what are you doing is unknown

What the thread title says its the model which I have, I didn't knew i have to write complete model in every reply, also I have mention clone from sunray which speaks itself that its without RS232 port.

= DM800HDse, so console usb port, needs JapharFlasher with USB cable to PC (and driver properly installed) and RJ45 to Router/Modem. JapharFlasher needs to be setup with proper IP address for the PC and correct IP address on same network for the Dreambox DM800HDse/Sunray clone. Then flashing a correct image, or correct SSL for Sunray clone Sim 2.10.

TS

pasted-from-clipboard.png

driver

IMG_20241209_143710~3.jpg

IMG_20241209_143049~5.jpg

IMG_20241209_143049~6.jpg

IMG_20241209_143131~3.jpg

IMG_20241209_144137~2.jpg

Check the frontpanel of the box, do you see the IP address on it ?

How did you connect the network part ? DM800HDse with RJ45 to the router/modem, and computer to the router/modem as well with RJ45 ?

What are your parameters of your network ? 192.168.0.x ? Router/Modem IP 192.168.0.1 ? etc... we need to know all details.

TS

Quote from tiku_2

the box is in HTTP mode, I typed the ip 192.168.0.106 in my chrome and edge browser, but its not opening.

what next?, see the second pic if i select 84d.nfi file and click on flash, it says calclating checksum, I can see the ip on the dm800hdse panel display.

IMG_20241214_221740~2.jpg

Hi, second photo above you made a mistake on the Lan to do the flesch only the Sim does not need to be activated, it must be written only with the Com.10 as I saw