Posts by tiku_2

"but there was never a 10 or 11, or 12... which are "based on openpli" but are not openpli as there is a lot of things changed or modified.

What about this one is it fake or original? & what you suggest, should i contine with the fake 12.3 in my A8P Sim or i install this 9.1 version.

Thread

openpli-9.1-release-20241227 For all supported devices

openpli-9.1-release-20241227 For all supported devices






https://openpli.org/











Enjoy & Good luck

ahmed gazye

Dec 27th 2024

Quote from toysoft

A8P Sim is original sim, so it works with latest drivers as well, but you need to find an image for original box. Original image for OpenPLi is 4.0.

https://openpli.org/download/dreambox/DM800+SE+HD

TS

Ok Thanks, Now please kindly solve my confusion, I also have A8P Sim and i installed this image openpli-12.3-dm800se-original-20240425, released by mrlu in my D11, everything went smoothly, see thie pic.Now my confusion is that, as you said that the last original open pli for DM800HDse is

this openpli-4-release-dm800se-20191216. and according to the openpli.org the last supported version is 9.1 dated 20241228 for Newer Devices, then how come mrlu released 12.3 for Dm800se, its very confusing.

Quote from toysoft

Absolutely, Ferrari are Kernel 2.6, and old images from 2012.

It is necessary to replace the sim on these boxes, to have the latest image available, and the Japhar sim has latest 2015 drivers, other sims estar/sim2 have drivers only from 2013, and Ferrari from 2012 (Kernel 2.6, and cannot with Ferrari sim work with Kernel 3.2).

TS

And what about A8P Sim?, which drivers does A8P Sim Has? and what is the last Open Pli supportive Image for A8P Sim?

Quote from toysoft

Quote from tiku_2

Check the Plugin Menu, to see if you have Japhar Addon Manager,

TS

Where is the plugin menu in my screenshot? Also there is no Software Management in my image Menu.

Display More

Here are the screenshots.

Quote from s3n0

Then go into the plugin (open the plugin). And then... use the YELLOW button on the RCU. That's it :-) .

How to go into the plugin? There is No word Plugin in the Menu or System.

Some one explained this

Copy this plugin into USB flash memory stick and plug-in into your receiver, then with Explorer installed in receiver browse to USB flash memory stick and install from it. And password is not need for this installation.

But i also don't have explorer installed in my image.

"I quickly searched, and found this: Enigma2 Reset Password Plugin When you run the plugin, use only the YELLOW button to reset the password. Do not use the backup, because the plugin is intended for another set-top box."

I downloaded,unzipped, copy the ipk file in a usb drive, it got installed, but i don't see any Plugins option in the Menu.

Goolgle:-

1. In OpenPLi, go to Main Menu > Plugins > Software management > Install local extension.

I don't have Plugins>software management in my MENU

Quote from toysoft

Ok, then you have this image, v4.0

openpli 4 dm800se

TS

Ok so now i know that it has openpli 4, so is there any newer version than this which supports my box?, or i just remove password from it and continue with this embedded image? Thanks

ok, its still asking for password, I tried empty(enter), and also with root,i think the pre owner of this box has changed the password, i have to flash a new image in

openpli 4 dm800se

dm800se login: root

Password:

Login incorrect

dm800se login:

dm800se login: root

Password:

Login incorrect

dm800se login:

dm800se login

Quote from s3n0

Regarding OpenWebif, try checking in the MENU GUI, using RCU, whether this OpenWebif is enabled and active. It should be somewhere in the MENU under networks or somewhere under network services.

I don't have any option in the menu to enable OpenWebif, not in system or user interface.

login as: root

root@192.168.0.105's password:

Access denied

root@192.168.0.105s password:

Access denied

I am getting access denied in putty.

toysoft I don't have information in any menu, First boot up menu shows Timer-Setup-Standby/Restart

In setup menu System-Service Searchin-/Softcam/CI-Parental Lock, If I Go Inside System, there in no information or about.

Also i cannot Telnet, because its password encryted, also no webif Error 404/Page Not Found.

I am getting box ip, connected via Lan Cable.

s3n0 Thanks once again for in-depth explaination, basically my requirement is the South Asian Satellites, Videocon D2H And Tata Sky Providers.

I am new to Enigma, i thought there must be some option in the menu functions that i can do a factory default, so the userboquets gets delete, but i didn't find anything, also i don't know whether if i do a Factory reset, I may end up loosing all the pre-intsalled pluggins, softcam, etc, then i have to re-install all of them from the scratch.

I am familiar with this tool Dreamboxedit, if this is the only way to delete userbouquets (Channels) then i will do it by DreamboxEdit, I don't want to do a full scan, because it will tune all the channels from the providers, rather i would prefer to tune the specific transponders according to my channel requiremenst.

FastScan is there in the Menu Option, I just want to check which version of OpenPli is installed in it, this box has been dumped more than 1-2 years back, so if there is a new version of Openpli released with the updated drivers, then i should try to upgrade my box. What you think?

Panda555 Yes i can Winscp to FTP with the box.

Thanks toysoft & s3n0, I already got openpli in my DM800HDse, but i dont know which version is installed in it, as i got this box from flea market, it had Greek native language in it, i changed it to English, thanks to mobile cam translator.

Now it has pre-tuned channels from 13.0 Eutelsat, and some iptv, I want to delete all those channels, how can i do that? My requirement is 93 Gsat & 88 ST2, Please someone guide me.

I did not get your point? " You havn't answered" i asked you to reply me in the thread not in pm.

Hello friends, Can anyone please suggest which is the best and fast image for Sunray DM800HDse Clone SSL84D Sim2.10,D11 Board (Single Tuner), i don't want multiboot, just a simple image to flash internal.

Thanks

Quote from piterfree

???????

ok...if so...the flesch mini usb device works well...the problem now I think is the Lan (it does not communicate), because to write the software it goes via Lan.

Sorry My Friend, I think i have jumple up everything, i am Riding on a two horse at a time, the software problem which you are referring to is the one Box which is D7, which i have mention in my post#24,#26, that box accepts Booloader, Firmware, and also gets detected in Flasher Tool, But after Succesful flashing everything, First Boot there is No Display on the TV Screen , Only Panel Oled Shows No Ca Found.

The Lan was communicating, i saw the right yellow led blinking when the image was uploading, also tried to upload image without selecting the ip (Unchecking Local Ip), though it took 12-13 Minutes to upload the image to the box, then the box Flash was written from inside, and Got Flash Copy Succeeded.

The Above Pics are from D11 Box, it has completely different problem, D11 Doesn't get detected in Flasher Tool, Below its not showing Box Type:

Now the problem is that, D11 is only showing connection prepared,now switch on the dreambox, When i Click On Connect Button in the Flasher Tool there is no Response from the box, infact it should immediately display the box type in the left below, but no box detection no green bar progress,it's only showing No Ca Found on the panel, I have tried all the flasher Tools, Sunray, Jaspher, Dreamup,optiflasher pro nothing works. This is a hardware fault and i have mention it in another forum to Johny.

here are the pics of D11 (No Ca Found)

Quote from piterfree

hi, but it could be possible that the software is not compatible and is not for clone, or try to exchange the sim that you know is working on another dream and test it on the one that is giving problems.

I already tried that, as i said in my previous reply, i checked all the sims in working D6 and all booted fine, i got three psus, all are ok.

Regarding the software uncompatibilty, this comes later, first i need the box to be detacted by the flasher tool, I mean its not showing box:DM800 in the left side in the Flasher tool, just box:- No green bar going, and the Display panel: Bios No Ca Found. But it sure gives a beep when i insert mini usb plug, also in the device manager shows cp210x uart-usb and the port it is assign to.

All my sims are DM800SE sim210, the third pic from above, i have one working dm800hdse D6 Board,sim 210, i have install vu+ blackhole image in it and its working ok,so i checked all the sims in D6 Working Board, all booted fine, then i replaced working sim in this box also flashed Blackhole image, everything went smoothly, disconnected the flasher and the cable, restarted Dreambox and its showing No Ca Found, Its A Hardware Fault.

My box is already open (without top cover) I have atleast three 2.10 sim, tried all, but no luck.

Also tried on windows xp, i think it has some hardware problem.