OpenATV 7.5.1 – Discussion & New Features

There are 435 replies in this Thread which was already clicked 153,165 times. The last Post () by Captain.

    Quote from azaz1

    Is it possible to add task to cron full backup image?

    how would that work if you have multiboot or not you need to select which slot and next you need to select target device to save image to.


    Edit just realised when you do image backup it also saves imagebackup.sh to tmp folder perhaps you could setup cron timer to run that i just copied it to script folder
    Capture.PNG

    My setup:


    Vu Uno 4kSE

    Openatv 7.4


    Vu Duo2

    Openatv 7.5.1


    Today I did a clean install on my Duo2 -installed Openatv 7.5.1. (version from 20250215).

    Installed remotechannelstreamconverter to get acces to TV channels from my Vu Uno 4kSE.

    Installed Xstreamity 4.80

    Installed service app so I can set this to exteplayer3 (I use this setting along with quarterpounder to unlock streams in Xstreamity).

    When I set service app to exteplayer3, all my channels disappear. I can see the bouquets but black screen on all. Seems like the exteplayer3 setting blocks out everything from the streamconverter.

    I also tried the fallback remote receiver setup, but with the same result.

    So Serviceapp need some fixing imo.

    This is not a problem in Openatv 7.4

    So its back to Openatv 7.4

    done the test...today with the move in ServiceApp internally on the RTMP protocol implementation line if you move the item on ffmpeg in its software there are 2 items to move checked carefully, then I activated the Extremeity plugin I have to confirm that it works perfectly.


    Pli_920

    VuSolo_VuSOLO.PRO_VuZero_VuSOLO2 SE_DR.800sim japar ed 800SEsim a8p_Mutant 51_4k_GB.UE.4k_DM.920+900
    H9combo_H9.2H-SE_H7s_H2H_H5
    thumbs up 1

    I have question. My receiver is octagon sf4008. I have symmetric internet access 600/600. I use openATV 7.5.1. Problem with switch streaming cannal and one solutions is just switch power off turn off. I don't know where is problem. Some canals online working good but some they are do problem. Which openATV version is good without any problems? I hope everything is understanding.20250221_201118.jpg

    This problem may not be due to the streaming.

    This could be the TV mode you have selected in the image.

    After installing the image you have to go to settings and select which type of video output suits the TV you have.

    For exemple:


    Go to - Settings , Video, video settings and her in lines 5 and 6 they say


    show content.....

    show content......


    You have to configure the image according to the TV you have.


    I use it like this:


    Show Content 4:3 as ----------------------------------------Pillarbox

    Show content greater than 16.9 as --------------------Latterbox




    You will have to see which of these solutions best suits the TV you have.


    Today I did a clean install on my Duo2 -installed Openatv 7.5.1. (version from 20250215).


    Installed remotechannelstreamconverter to get acces to TV channels from my Vu Uno 4kSE.


    Installed Xstreamity 4.80


    Installed service app so I can set this to exteplayer3 (I use this setting along with quarterpounder to unlock streams in Xstreamity).


    When I set service app to exteplayer3, all my channels disappear. I can see the bouquets but black screen on all. Seems like the exteplayer3 setting blocks out everything from the streamconverter.


    I also tried the fallback remote receiver setup, but with the same result.


    So Serviceapp need some fixing imo.


    This is not a problem in Openatv 7.4

    5002 (exteplayer3) working here no problem with xtreamity 4.86

    P.S. when I install serviceapp i just leave settings as default

    If you leave serviceapp at default you will not be using exteplayer3. As I mentioned, when activating the exteplayer3 in service app, it blocks my TV channels that I get from my Vu+ Uno 4k SE server using Remotechannel Streamconverter. If I wasn't using the RemoteChannelStreamconverter, it would not be a problem. So, in other words, the exteplayer3 blocks my TV channels when using RemoteChannelStreamconverter.

    Is Quad PIP install working for anyone with 7.5.1? Doesnt seem to finish installing and then just gives a warning "plugin is not available - Extensions/ QuadPip No module named 'Plugin-SystemPlugins- QuadPIP".

OpenATV Team Images Support Forum ~ based on OE-Alliance

OpenATV Supported Models ~ Airdigital, Amiko, Anadol, Atemio, Atto, AX Technology, Axas, Beyonwiz, Dinobot, Dreambox, Edision, EVO, Ferguson, Formuler, Galaxy Innovations, Gigablue, Golden Interstar, HDBox, Hitube, James Donkey, IQON, Izibox, Jepssen, Maxdigital, Medialink, MaXytec, MediaArt, Megaset, Miraclebox, MK-Digital, Mut@nt, Novaler, Octagon, Odin, Optibox, Protek, PULSe, Qviart, Red-Eagle, Relook, Roxxs, SAB, Sezam, Sogno, Space, Spycat, Technomate, Telestar, Tiviar, T-Rex, Uclan, Venton Unibox, Vimastec, VisionNet, VU+, VUplus, World Vision, Vizyon, WWio, Xsarius, and Xtrend.

Participate now!

Don’t have an account yet? Register yourself now and be a part of our community!

Register Yourself Login