Hello, I have a few questions about Dreambox ONE UHD. I would appreciate your help.

There are 74 replies in this Thread which was already clicked 5,641 times. The last Post () by disa51.

    Quote from 1z1z

    Hello dear friends, first of all, I have a question. Now I need to connect a LAN cable from the Dreambox One and a LAN cable from the computer to the modem router. If this is the case, I did it, but nothing happens in the browsers when I enter the IP. Then a few questions

    1- Do I have to do something in the modem router itself or enter something?

    2- Given the IP that I set through the modem router in the Dreambox One, what numbers should I enter in the computer in the internet protocol version 4 section in the IP Adress & subnet mask & Default gateway & DNS SERVERS sections?

    I have posted a few pictures below of the Dreambox One and the computer. In each case, if I need to do something or if there is a problem, please let me know. I would be grateful.

    You don't need to do anything because the router automatically assigned you an IP address. All you need to do is when you want to install the image, enter the IP address of the dreambox one on your website and you will get contact with it and there you can flash the image.

    • Official Post

    You keep saying modem, it is a router. Please accept this, don't argue.


    Your Dreambox and PC have to be on the same network.

    Connect your PC to the router with and ethernet cable.

    Connect your Dreambox to the Router with an ethernet cable.


    Once you have connected everything correctly, reboot the Router, the PC and Dreambox and start again.

    Hello dear friends, first of all, I have a question. Now I need to connect a LAN cable from the Dreambox One and a LAN cable from the computer to the modem router. If this is the case, I did it, but nothing happens in the browsers when I enter the IP. Then a few questions

    1- Do I have to do something in the modem router itself or enter something?

    2- Given the IP that I set through the modem router in the Dreambox One, what numbers should I enter in the computer in the internet protocol version 4 section in the IP Adress & subnet mask & Default gateway & DNS SERVERS sections?

    I have posted a few pictures below of the Dreambox One and the computer. In each case, if I need to do something or if there is a problem, please let me know. I would be grateful.

    Quote from 1z1z

    Hello dear friends, first of all, I have a question. Now I need to connect a LAN cable from the Dreambox One and a LAN cable from the computer to the modem router. If this is the case, I did it, but nothing happens in the browsers when I enter the IP. Then a few questions

    1- Do I have to do something in the modem router itself or enter something?

    2- Given the IP that I set through the modem router in the Dreambox One, what numbers should I enter in the computer in the internet protocol version 4 section in the IP Adress & subnet mask & Default gateway & DNS SERVERS sections?

    I have posted a few pictures below of the Dreambox One and the computer. In each case, if I need to do something or if there is a problem, please let me know. I would be grateful.

    I wrote to you that you don't need to touch anything because you got the IP address from the router on the dreambox one. All you need to do is turn off your dreambox one because you have an off button on the back. When you turn it on, press the button on the front and wait for Recovery mode to appear. Go to your PC and enter the address 192.168.1.100 from the dreambox on the website and you will get contact with him so you can flash the image.

    • Official Post

    He has set his PC IP address to be the same as his router.


    Please stop manually assigning things and leave everything in automatic mode. Both ip v4 and ip v 6. On your PC, select/enable the following options:

    Obtain an IP address automatically

    Obtain DNS server address automatically.


    Reboot and try again. You are going to flash your receiver while in recovery mode, so the setting in Enigma2 won't be applied.

    Quote from 1z1z

    Hello dear friends, I have a problem installing the image GP4.2 AIO on the Dreambox One. As you can see in the image below, after sending the image to the Dreambox One, this message appears:

    First, what is the problem that this message appears on the Dreambox One.

    Second, which option should I choose?

    Did you install the image on your dreambox?

    No, I didn't install it.

    The problem is that when I click the yes all option according to the image above, I think it will take 4 to 5 hours for Dreambox One to install the One Image, and when I realized this, I turned off Dreambox. When I click the NO option, nothing happens. I haven't tested the YES BUT ONLY SOME option yet to see what happens.

    Quote from 1z1z

    No, I didn't install it.

    The problem is that when I click the yes all option according to the image above, I think it will take 4 to 5 hours for Dreambox One to install the One Image, and when I realized this, I turned off Dreambox. When I click the NO option, nothing happens. I haven't tested the YES BUT ONLY SOME option yet to see what happens.

    I wrote you how to install the image. I don't know if you read it. You have to turn off your Dreambox One from the power. There is a button behind the off/on. Watch the video I sent you on how to properly install the new image. I don't know, but if you don't do what people tell you, you won't install it properly.

    1z1z

    You had the experimental image OE 2.6 installed with the Gp4.2 panel. When you sent the AIO image, you left the selection for the backup and restore of the settings of the previous image, creating a conflict situation.


    Try to select "no" and see if it will allow you to continue with the initial setup -language, sat, etc. If all goes well, I recommend repeating the flash to get the optimal condition.


    If it does not settle, I would advise you to perform an online recovery from the recovery mode, complete the initial configuration, then repeat the flash of the AIO image with Gp4.2. During these operations, you must have everything connected to the network.

    Edited once, last by disa51 ().

    Hello dear friends, I have a Dreambox One with the image GP4.2 AIO installed on it.

    I installed an OScam emu on it and now I want to delete and remove that OScam emu. Everything I did didn't work. With the commands dpkg -r and opkg remove nothing happens at all. By the way, what is the best OSCAM EMU for Dreambox One with image GP4.2 AIO ? Please send me the file.

    Please advise how to remove it.

    Edited 3 times, last by 1z1z ().

    Shocked 1

    Dear friends, regarding Dreambox One and Image GP4.2 AIO in the file oscam.conf option extended_cw_api = ? what should its value be? The value should be 1 or 2. Which should it be?

    By the way, what is the best OSCAM EMU for Dreambox One with image GP4.2 AIO ? Please send me the file.

    Edited once, last by 1z1z ().

    Thread
    Levi45 Multicam Manager
    This plugin comparable with PY2 and PY3 , also compatible with any enigma2 boxes with any image .


    On bh image you may need to give this comand via telnet


    Code:

    (Code, 3 lines)


    All this for test purposes only ,me or satellite-forum not responsible for any issue caused


    you can install plugin via ipk/deb or telnet command
    (Code, 1 line)

    levi45

    Hello dear friends, I have a question. When the internet modem and Dreambox One are connected to the router and I go to the plugins section in Dreambox One and click the red button, which means Manage extensions, shouldn't it start downloading like when the Dreambox One is directly connected to the internet modem?

    When I connect the internet modem and Dreambox One to the router and go to the plugins section and click the red button, which means Manage extensions, nothing happens. But when I connect the Dreambox One directly to the internet modem and do this, the download is activated and starts downloading.

    I am posting pictures of the modem, router, and Dreambox One network settings below. Please advise. If there is a problem with my settings, please let me know. I would be grateful.

    I don't know if you read when people write to you or not.

    We wrote to you a long time ago but you keep doing something else.

    Your modem is a router and I don't know what you want to connect when you have contact with your Dreambox one. As far as I understand you, you want to connect another router to the modem you are calling, and your modem is a router.

    Hello again

    Dear friend, I understand what you are saying. By the way, I connect the internet modem and Dreambox One to the Linksys router.

    Then to test, I go into the Dreambox One and the plugin section and then I press the red button that means Manage extensions but nothing happens. And no download is done.

    By the way, I know that if I connect the internet modem directly to the Dreambox One, the download operation is done in the plugin section and by pressing the red button, which means Manage extensions, but I want to know whether the download operation is also done in the situation that I said above?

    Now I have a question for you, dear friend, with these things I said and that the Dreambox One and the internet modem are connected to the Linksys router and when I enter the plugin section and press the red button that means Manage extensions, should the download take place or not?

    Now, if in your opinion the download operation should be performed, then why is there no download for me.

    I also put these pictures above so that if there are problems with my settings, you can advise me.

    Thank you

Dreambox One 4K UHD 2160p H.265 Enigma2 Linux Android Dual Wifi DVB-S2X MIS Satellite Receiver.

Download DreamOne Dreambox One 4K UHD Android CoreELEC, DreamOS Firmware and Enigma2 Images. Team Support from DemoniSat - Dream-Elite - Gemini Project GP4 - Merlin Project - NewNigma2 - Peter Pan Neverland - OpenBh - OpenPLi Japhar - OpenATV - OpenVision - PurE2 - SatLodge.

Participate now!

Don’t have an account yet? Register yourself now and be a part of our community!

Register Yourself Login