carte fransat prob ncam /oscam

There are 42 replies in this Thread which was already clicked 9,151 times. The last Post () by popo40.

    No.France 3 work 0500@041950 and ETB1/On ....that's why I managed to find it. 0500@042820/041950/041960 Bis Tv c hops server,and work total channels.and 13E total ,and 19,2E AStra 5 channel,total 0500@042820

    I had intended to use the new PCMCIA module with my current PC7 card.

    I run a Vu+ Duo4K SE , openATV 7.3 includding <ciplushelper>

    I note that this post indicates some problems ?
    CAM Fransat CI+ 1.3

    Edited 2 times, last by IamMattM ().

    popo40
    until061

    Have you got a solution to this matter since the 27th April 2026 ?

    Not sure if I should be getting more than just a black screen as I see Nano98 and ecms:

    Edited 3 times, last by IamMattM ().

    This is what Gemini AI tells me:

    "Your log Detected /dev/dvb/adapter0/demux0 Api: 0 is the primary reason the picture isn't showing.
    Api: 0     is an old protocol that often cannot handle the 16-byte "Long CW" generated by your card. Modern VU+ 4K boxes usually require Api: 3."

    "Since pmt_mode = 6 didn't force it to change, it indicates your OSCam-Emu version 802 is too old or patched specifically for Stream Relay (iCam), which can break local card descrambling on 4K ARM hardware."

    "Your log shows OSCam-Emu version 802. This version is quite old and often hard-coded for older DVB-API versions (Api: 0). For a VU+ Duo 4K SE to properly "see" 16-byte Fransat keys on the screen, you typically need a modern binary (Version 117xx or 118xx) that correctly triggers Api: 3."

    Just out of curiosity, in case anyone knows, what exactly was the update? I have a Fransat Strong receiver, it's been updated and now the channels are working again, but not on Vu+ with Oscam. Is it a change to AESKEY or something else?

    Quote from rubeneo

    Just out of curiosity, in case anyone knows, what exactly was the update? I have a Fransat Strong receiver, it's been updated and now the channels are working again, but not on Vu+ with Oscam. Is it a change to AESKEY or something else?

    I think either the AES or DES key...It sounds like Multistream if supported by your Vu+ hardware is a way forward and no keys needed. I certainly will be doing this workaround on my Vuduo4KSE, so that I can once more watch TNT channels remotely and not be bound by the location of my LG TV.

    Bonsoir à tous.
    Donc, j'ai installé Ncam 15.7 pour le tester, mais je n'ai rien dans le serveur Ncam ou les paramètres utilisateur, et j'ai ce message sur le panneau d'administration Ncam : « ? ». Comment puis-je supprimer cela ? Merci pour vos conseils.


    Capture-d-ecran-2026-05-05-210646.png


    vu+ duo2,vu+zero4k,vu+ultimo

    dvbdream . haupage /tbs6983 vplug

    antenne bande c / 2.80cm/antenne ku/ channel master 150cm

    Edited once, last by popo40: mauvais poste ().

    Quote from aigle74

    hello I am looking for a complete config for FRANSAT 5W I am ready to pay, I have a V7 card with an ultimo 4K thank you in advance

    aigle74

    Isn't your Ultimo 4K already fitted with a     DVB-S2X FBC tuner module (specifically the 45308X chipset) ? If so then supposedly you can get TNT channels using multistream as I have just found out. Everything working again perfectly and without a need for any cards/oscam at all.

    Edited once, last by IamMattM ().

    Quote from popo40

    Bonsoir à tous.
    Donc, j'ai installé Ncam 15.7 pour le tester, mais je n'ai rien dans le serveur Ncam ou les paramètres utilisateur, et j'ai ce message sur le panneau d'administration Ncam : « ? ». Comment puis-je supprimer cela ? Merci pour vos conseils.



    Hey, don’t take it bad, but you should not post screenshot like this.


    You’re posting your line information + IP adresses of your « friends ». These are gold information for attackers.

    Edited once, last by until061 ().

    until061

    These are servers that are added when you add the ncam15.7 IPK file in the admin panel without adding anything to the ncam server settings. I'm wondering how to remove them.

    vu+ duo2,vu+zero4k,vu+ultimo

    dvbdream . haupage /tbs6983 vplug

    antenne bande c / 2.80cm/antenne ku/ channel master 150cm

    thumbs up 1

    There's nothing in the server file, only the two emulators, no server


    [reader]

    label = Device_SoftCam

    protocol = emu

    device = emulator

    disablecrccws_only_for = 0E00:000000

    caid = 0500,0604,0D00,0E00,1010,1801,2600,2602,2610

    detect = cd

    ident = 0500:020A00,021110;0604:000000;0D00:0000C0;0E00:000000;1010:000000;1801:000000,001101,002111,007301;2600:000000;2602:000000;2610:000000

    group = 1

    emmcache = 2,1,2,1

    ccchop = 1

    emu_auproviders = 0604:010200;0E00:000000;1010:000000;4AE1:000011,000014,0000FE

    emu_datecodedenabled = 1







    vu+ duo2,vu+zero4k,vu+ultimo

    dvbdream . haupage /tbs6983 vplug

    antenne bande c / 2.80cm/antenne ku/ channel master 150cm

    Edited 2 times, last by popo40 ().

Your resource for Ncam softcam.

Find configs, tools, downloads, and community support for setup, optimization, and card/server management. Master modern card sharing with Ncam. Access configurations, tools, downloads, and dedicated support for efficient Enigma2 server/client setup.

Participate now!

Don’t have an account yet? Register yourself now and be a part of our community!

Register Yourself Login