the m3602allcode.abs has to be an old version,TDV08180-1.0.0.0
with the version TDV09030-1.0.0.0 the tuner doesn't work.
the openbox has to be a clone or have the resistors to the prot ic removed to isolate it.
-- dashed s10 tuner
- lutz diagram
- Thread is marked as Resolved.
-
-
some versions of the firmware have caskeydb.bin embedded,which can be saved to pc but I couldn't find any program that will edit it.
a 64k bin file. -
the m3602allcode.abs has to be an old version,TDV08180-1.0.0.0
with the version TDV09030-1.0.0.0 the tuner doesn't work.
the openbox has to be a clone or have the resistors to the prot ic removed to isolate it.Kindly let me m3602allcode.abs old version,TDV08180-1.0.0.0
-
Manhattan rs 1933 firmware will boot and run on the s10 with the prot ic isolated,but the front panel doesn't work.
Should also run on a clone.You have to replace the remote code table in firmware to use with an openbox s10 remote. -
lutz diagram Good day, my friend! Be kind, help me. Need to replace the remote code table in firmware. I know you have experience. Firmware on the processor ALI3606. Need to replace the remote code table in firmware to use with an openbox s10 remote. Thanks in advance!
-
couldn't find it.
it is usually the 448 bytes between the "genneral wakeup message!" and "system_init_process"
11 00 XX XX strings but I couldn't find it.Doesn't look like the usual 3606 firmware to me. -
This receiver Hiremco Rocket HD.
http://www.merihvideo.com.tr/urundetay.php?prod=56 -
May I come in here, because my S10 no longer accepts official f/w. I was having problems with no signal to tv and was trying different files, but I think it was anonymous last f/w that has caused the dreaded --. I am reading this but not being a techie, I find it a bit confusing. No fix yet?
Thanks. -
IMHO there will never be a fix for the -- other than being stuck using anonymousx firmware.
That was the reason he developed the modded firmware in the 1st place.
The only alternative is hardware mods or replacing the protection ic that got corrupt,like from a receiver with other problems but that requires surface mount soldering/desoldering which requires expertise and the proper hot air equipment. -
After my chip got corrupt I tried buying a new s10 receiver but it used a totally different protection ic.So I couldn't try to get any info from that chip.It has a 32pin chip instead of the usual 8pin
-
The "new" s10 actually looked older than the 1st s10 I had.
It had a separate board for the ethernet instead of just being on the mainboard. -
lutz diagram Good day, my friend! Be kind, help me. Need to replace the remote code table in firmware. I know you have experience. Firmware on the processor ALI3606. Need to replace the remote code table in firmware to use with an openbox s10 remote. Thanks in advance!
I don't know what the goal is,do you have that receiver and just want to use an openbox remote?
-
lutz diagram I have another receiver. on which fell off firmware. The original firmware does not start. Even tried a programmer. I only found three firmware (this is one of them) that run on this unit. But does not work the remote control. And I can not insert code to check the receiver.
-
so you are trying to run different firmware on the s16?
It is tough finding the remote code in the firmware you posted
You may be better of buying a replacement remote to match or trying to use a universal remote -
This is not the S16. It is a dead receiver azclass mini hd
-
that takes a 4meg .abs file
the firmware in your other post was for an 8meg flash -
There's flash is set to 8 Meg. EN25Q64.
-
I couldn't find it in the firmware you posted
-
There are two more firmware that are triggered. But the remote control does not work either.
-
the bravo is easy,the remote stuff is in the usual spots but you have to manually extract the maincode from the .abs and decompress edit and recompress.
Participate now!
Don’t have an account yet? Register yourself now and be a part of our community!