avatar2 spark system stuck on BOOT

Hello i don't know how i did it but i was in spark trying to make a default reset when my receiver an avatar2 didn't want to boot up and it stuck on the front panel on "BOOT" In the other side the enigma2 works fine, and whether in spark or enigma i can have all the messages in the front panel like "SUCCES" "FORMAT" "U LD" everything is ok. But whatever i do like reflashig it with rescue images from alien2 or triplex nothing can make it change from "BOOT". The flashing goes fine from "FACT" to "SUCCES" .
I have this message (in bold) using putty which i think may be the cause of my damage (I never used putty before) but iam not sure, see please and tell me what to do:

Board: STx7105-PDK [32-bit mode]

U-Boot 1.3.1-g72483220 (Jan 17 2012 - 17:10:49) - stm23_0051 - YW_1.1.003-9-g724 8322 overclock

DRAM: 256 MiB
NAND: Bad block table found at page 262080, version 0x01
Bad block table found at page 262016, version 0x01
512 MiB
SPI: info: found S25FL016K (2MiB) device (page=256,erase=65536)
warning: SPI device may be write-protected (status=0x9c)
In: serial
Out: serial
Err: serial
Ident ic exist
Ident ic get stb id
IdentID : 0c 00 0b 00 00 07 5b
Hit ESC to stop autoboot: 0

Loading from NAND 512MiB 3,3V 8-bit, offset 0x100000
Image Name: Kernel-Ramdisk-Image
Image Type: SuperH Linux Multi-File Image (gzip compressed)
Data Size: 5821310 Bytes = 5.6 MiB
Load Address: 80800000
Entry Point: 80801000
Contents:
Image 0: 2970053 Bytes = 2.8 MiB
Image 1: 2851242 Bytes = 2.7 MiB
## Booting image at 80000000 ...
Image Name: Kernel-Ramdisk-Image
Image Type: SuperH Linux Multi-File Image (gzip compressed)
Data Size: 5821310 Bytes = 5.6 MiB
Load Address: 80800000
Entry Point: 80801000
Contents:
Image 0: 2970053 Bytes = 2.8 MiB
Image 1: 2851242 Bytes = 2.7 MiB
Verifying Checksum ... OK
Uncompressing Multi-File Image ... OK
stmac_phy_get_addr(): id1 = 0xffff, id2 = 0xffff
found phy at addres = 2
stmac_phy_get_addr(): id1 = 0x7, id2 = 0xc0f1
stb_id = c0b0075b
Loading Ramdisk to 81d47000, length 002b81aa ... OK

Starting kernel console=ttyAS1,115200 rw ramdisk_size=6144 root=/dev/ram0 init=/ linuxrc ip=192.168.0.69:192.168.3.119:192.168.3.1:255.255.0.0:Spark:eth0:off stm maceth=msglvl:0,phyaddr:2,watchdog:5000 bigphysarea=7000 nwhwconf=device:eth0,hw addr:30:00:0B:00:07:5B Manufacture=Spark-Project STB_ID=0C:00:0B:00:00:07:5B - 0 x01548000 - 2851242 ...

Yes Ben361 it is the same as avatar 2+ but this one is espacially for north africa with two DVBs tuners

Not yet trying find a solution before...Tanx anyway

Please help this log from putty it may help to know some problems :

[MAIN] init finish,errCode=0
[ YWDBASEv_GetData][ 578] error 0x1f40006
[ YWDBL_CommGetVolume][ 288] YWDBLi_CommGetByFldNoWithDefault COMM_VOLUME errTy
[ YWDBASEv_GetData][ 578] error 0x1f40006
[YWDBLi_ScGetByFieldNo][ 101] YWDBL_GetSysCfgField uFieldNo = 15[YWDBL_ScGetRes
########################## uiCompSize[0X00AE8BCC]================
[*error*][YWFILE_IsDbFileOk:562]===Open file[./AppUserDb/syscfg.bin] failed===
[*error*][YWFILE_ReadFlashToDB:816]===Read [./AppUserDb/syscfg.bin] failed, take
[*error*][YWFILE_IsDbFileOk:562]===Open file[./AppUserDb/syscfgbak.bin] failed==
[*error*][YWFILE_ReadFlashToDB:822]===Read [./AppUserDb/syscfgbak.bin] failed, t
[*error*][YWFILE_IsDbFileOk:562]===Open file[./AppUserDb/syscfgdef.bin] failed==
Starting kernel console=ttyAS1,115200 rw ramdisk_size=6144 root=/dev/ram0 init=/ 00 bigphysarea=7000 nwhwconf=device:eth0,hwaddr:30:00:0B:00:07:5B Manufacture=Sp

No it iddn't work i have already done it before....Thank you

Did you see these errors above? What do you suggest?